Argos ZVK1000BU-CE-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 100cm

Depth - 59cm

Height - 89.5cm

Athina - 1000 Base Unit

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 23/12/09

Important - Please read these instructions fully before starting assembly

608/0811

608/0938

608/0873

608/0990

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 42kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D0315A)

(870 X 570mm)

Right Side (D0316A)

(870 x 570mm)

Door (D0317A)

(716 x 497mm) x 2

2

9

Base (D0323A)

(970 X 499mm)

Shelf (D0324A)

(969 X 427mm)

Rail (D0321A)

(970 x 60mm) x 2

Plinth (D0322A)

(970 x 150mm)

Top (D0339A)

(1000 x 590mm)

Back (X740)

(980 x 533mm)

Munting (D0324A)

(689 x 60mm)

3

4 5

6 7

8

10

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 14

B

Metal dowel (F901) x 10

C

D

Shelf support (F110) x 4

E F

G H I

Rule Scissors Hammer Eye protection

(when using a hammer or drill)

Cross-head screwdriver

Nail (F51) x 14

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J

Door Buffer (F137) x 4

L

Electric drill

Large locking nut (F900) x 10

Bracket (F945) x 4

25mm Screw (F50) x 4

13mm Screw (F63) x 813mm Screw (F79) x 6

K

Hinge Plate (F853) x 4

Hinge (F852) x 4

M

Handle (F847a ) x 2

a

M

Handle Screw (F847b) x 4

b N

40mm Screw (F910) x 2

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

B

1

K

Front edge

Step 2

a:

b:

K

Prepare the left side

a: Fit 2 hinge plates

onto the left side , making sure that the slot is facing towards the front edge.

b: Screw 5 metal

dowels into the holes shown on the left side . .

Note: Tighten metal dowels up fully against the panels.

1

B

1

Fit 2 brackets to the left side

Fit a bracket to the left side , 100mm in from the back edge, see diagram.

Fit another bracket to the left side , 100mm down from the top edge, see diagram.

Secure each bracket using screw .

Note: The brackets must be flush with the edges of the panel.

1

F

H

1

100mm

F

H

F

H

Assembly Instructions

5

Step 3

Step 4

B

2

Front edge

K

2

K

Prepare the right side

a: Fit 2 hinge plates

onto the right side , making sure that the slot is facing towards the front edge.

b: Screw 5 metal

dowels into the holes shown on the right side . .

Note: Tighten metal dowels up fully against the panels.

2

B

2

100mm

F

HH

Fit 2 brackets to the right side

Fit a bracket to the right side , 100mm down from the back edge, see diagram.

Fit another bracket to the right side , 100mm down from the top edge, see diagram.

Secure each bracket using screw .

Note: The brackets must be flush with the edges of the panel.

2

F

H

2

F

Assembly Instructions

6

Prepare the base

Insert 4 large locking nuts into the base as shown.

Note: Arrow on locking nut must point towards hole in edge of panel.

Tap 6 wooden dowels into the base as shown.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Step 5

Step 6

C

4

Fit the base to the right side

Push the base onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

4

2

C

4

C

10mm

A

4

A

C

A

C

4

Finished

front edge

B

4

C

2

Assembly Instructions

7

Step 7

Step 8

Fit a rail to the right side

Push one of the rails onto the right side as shown.

Use a screwdriver to tighten the large locking nut .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

6

2

C

A

C

A

6

Prepare the 2 rails and munting

Insert 2 large locking nuts and 2 wooden dowels into each of the 2 rails .

Tap 2 wooden dowels into the munting .

C

6

8

A

8

A

2

6

Assembly Instructions

8

Step 9

A

C

7

Prepare the plinth

Insert 2 large locking nuts and 2 wooden dowels into the plinth . .

C

7

A

Fit the munting

Fit the munting to the rail and base and secure using 2 screws . .

8

N

6 4

Step 10

N

8

N

6

4

Assembly Instructions

9

Step 11

Step 12

6

Fit the rail and plinth

Push the rail and plinth onto the right side as shown.

Use a screwdriver to tighten the 2 large locking nuts fitted to the 2 panels, as shown.

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

Note: Support the rail . until the left side has been fitted in the next stage.

7

2

C

6

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the 5 large locking nuts fitted to the base , rails and plinth .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

6

7

1

4

C

2

6

7

6

7

4

1

Assembly Instructions

10

Step 13

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Slide the back

into the grooves along the left and right sides, as shown.

c: Secure the back

by tapping 7 nails down into the back edge of the base and 7 nails into the back edge of the rail .

Stand the unit up for the next stage.

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

1 2

D

10

4

6

D

10

b:

c:

x

y

x

10

D

1

2

6

4

Assembly Instructions

Step 14

11

Step 15

Secure the front of the top

To secure the front of the top , screw up through the 4 holes in the rail at the front of the unit using screws .

Fit the top

Position the top onto the unit, making sure that the back edge is flush with the back edge of the sides and .

Secure the top using screw through the 2 brackets fitted at the top edge of the side panels and .

H

3

2

1

3

F

2

1

3

6

G

H

F

H

F

G

3

6

3

2

1