MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Venice - Large Corner TV Unit
Assembly Instructions - Please keep for future reference
450/9071
459/9641
Width - 119.8cm
Depth - 39.19cm
Height - 51.2cm
Issue 1 - 13/10/15
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 25kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
When applicable, remove any
protective film before use
2
1
2
Side (DF5748)
(47.7 x 23mm) x 2
Horizontal (DF5751)
(112.4 x 35.2cm) x 2
Plinth (DF5750)
(112.4 x 9.6cm)
Left Drawer Front (DF5752)
(55.9 x 20cm)
Top (DF5746)
(119.8 x 39.1cm)
Top Divider (DF5755)
(18 x 35.1cm)
Lower Divider (DF5753)
(17.1 x 35.1cm)
Back (DF5749)
(47.7 x 58.6cm)
Right Drawer Front (DF5754)
(55.9 x 20cm)
Left Drawer Side (W210-124LH)
(21 x 12.4cm) x 2
Right Drawer Side (W210-124RH)
(21 x 12.4cm) x 2
Drawer Back (W522-124)
(52.2 x 12.4mm) x 2
Drawer Base (T533-207)
(53.3 x 20.7mm) x 2
3
4
5
6
7
8 9
10 11
12
13
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
Metal dowel (F901) x 18
C
D E
Large locking
nut (F900) x 14
F
G
Hollow core
locking nut
(F892) x 4
I
Small locking
nut (F3) x 4
H
Knock-in Peg (F171GY) x 8
Drawer runner (F307) x 4
J K
P
L
M
Wedgefix (F639) x 4
Large wooden dowel (F40) x 2 Wooden dowel (F22) x 6
Small metal dowel (F893) x 4
45mm Screw (F65) x 4
40mm Screw (F910) x 4
19mm Screw (F461) x 4
9mm Screw (F73) x 8
9mm Screw (F74) x 4
N
O
Handle (FBARH128) x 2
8 9
Assembly Instructions
4
Step 1
A
B
A
B
Step 2
Prepare the 2 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts and .
Note: Tighten the metal
dowels up fully against
the panels.
A
8 9
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
B
10
11
Attach the drawer
sides to the drawer
frontS
Push a left drawer side .
and a right drawer side .
onto the back of each
drawer front and .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
10
11
8 9
B
B
10
11
B
B
B
10
11
A
A
10
11
A
A
Note: The right drawer front
has a small identification hole.
8 9
x 2
x 2
x 2
O
F
F
Assembly Instructions
5
Step 4
8 9
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front and .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 7
13
10 11
8 9
12
10 11
13
12
12
F
10 11
F
13
10
11
10
11
13
12
F
I
I
I
Fit the wedgefixes
Turn the 2 drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
I
x 2
x 2
x 2
x 2
L
L
Step 6
Attach the handles
Attach a handle to
each of the drawer fronts
. and using screws
. .
L
8 9
O
8 9
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 8
A
A
A
A
Prepare the top
Screw 4 metal dowels
into the top .
Screw 4 small metal
dowels into the holes
on the top .
Note: Tighten metal
dowels up fully against
the panels.
E
A
2
E
2
E
E
E
E
2
C
C
C
H
10mm
H
Prepare the top divider
Insert 2 large locking
nuts into the
top divider .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into the top divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
H
H
Step 9
C
A
Fit the top divider to
the top
Push the top divider
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top divider .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4
2
C
C
4
C
4
4
4
Step 10
4
2
Fit a horizontal
Attach a horizontal to
the top divider using
2 screws .
Assembly Instructions
7
Step 11
Step 12
Step 13
C
C
C
C
Prepare the 2
horizontals
Insert 4 large locking
nuts into each of the
2 horizontals .
C
3
3
4
K
K
3
4
x 2
K
G
G
Fit the 2 large wooden
dowels
Gently tap the 2 large
wooden dowels
through the horizontal
and into the top divider
. until they ‘’bottom
out’’.
G
3
4
3
4
3
Note: Support the
horizontal until the right
side has been fitted.
Assembly Instructions
8
Step 14
Prepare the right side
a: Place a runner
onto one of the sides .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the side .
c: Screw 5 metal
dowels into the side
. .
Push 2 hollow core
locking nuts into the
side , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
D
D
D
P
1
M
P
M
a:
b:
c:
B
1
D
1
D
D
1
M
P
M
M
P
D
A
A
A
A
A
D
1
1
1
Assembly Instructions
9
Step 15
3
Fit the right side
Push the right side
onto the top and the
horizontal .
The 2 small metal dowels
. fitted to the top
must slide into the top of
the 2 hollow core locking
nuts fitted to the right
side . .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
1
2
3
E
2
D
1
D
1
2
1
C
3
D D
Assembly Instructions
10
Step 16
Finished
front edge
Finished
front edge
Finished
front edge
Prepare the lower
divider
a: Place a runner
onto the lower divider .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
use the 2nd hole from
the back to fit the 2nd
screw .
c: Tap 2 wooden
dowels into the lower
divider .
Turn the divider over
d: Place a runner
onto the lower divider .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
e: Slide the runner
back the other way and
use the 2nd hole from
the back to fit the 2nd
screw .
P
5
M
P
M
M
5
M
P
M
Finished
front edge
M
P
a:
b:
c:
d:
e:
M
P
M
H
H
Finished
front edge
M
P
M
M
Finished
front edge
Finished
front edge
H
5
Turn the divider over
5
5
5
5
5
Assembly Instructions
11
Step 17
Finished
front edge
Fit the lower divider
Push the lower divider
down onto the horizontal
. .
5
5
3
3
K
K
3
1
Fit the other horizontal
Fit the horizontal to
the right side and the
lower divider .
Attach the horizontal
to the lower divider
using 2 screws .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
Step 18
3
3
1
5
5
K
5
C
3
Assembly Instructions
12
Step 19
H
Fit the plinth
Push the plinth onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the plinth
. .
C
Step 20
C
C
H
Prepare the plinth
Insert 2 large locking
nuts into the plinth .
Tap 2 wooden dowels
into the plinth .
H
C
7
7
7
7
1
7
1
7
Assembly Instructions
13
Step 21
D
Prepare the left side
a: Place a runner
onto one of the sides .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the side .
c: Screw 5 metal
dowels into the side
. .
Push 2 hollow core
locking nuts into the
side , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
D
D
D
P
1
M
P
M
1
1
M
P
a:
b:
c:
A
1
D
1
D
D
1
M
M
P
A
A
A
A
A
D
1
Assembly Instructions
14
Step 22
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to turn
the nuts inside the 2
hollow core locking nuts
. fitted to the left side
. .
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the horizontals and
the plinth .
C
7
1
1
3
7
1
3
3
2
D
2
Fit the back
Push the back down
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the back .
Step 24
Step 23
C
C
Prepare the back
Insert 2 large locking
nuts into each of the
back .
C
6
6
6
2
6
C
6
Assembly Instructions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
15
ALR3254
Step 25
Fit the drawers
Slide both the runners
forward and locate the
drawer sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .
Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.
Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.
Assembly is complete
N
P
P
N
2nd threaded
hole
P
N
10 11
N
N
Remember: The right
drawer front has a
small identification hole
(refer back to Step 1).
10
11
Secure the back
Secure the back to
the 2 horizontals
using 4 screws .
Carefully stand the
unit up for the next
step.
J
6
3
3
3
J
J
6
J
J
Step 26
Warning: The
unit is heavy.
Lift with care.
Loading...