Argos ZTSDT-WHBG-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

New Sywell - Dresser and Stool

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 25/09/14

Important - Please read these instructions fully before starting assembly

239/6994

247/9684

258/7040

259/7975

Dresser

Dimensions

Width - 77.5cm

Depth - 40cm

Height - 74.5cm

Stool

Dimensions

Width - 43cm

Depth - 35.5cm

Height - 48cm

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 24kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

2 3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

4

Left Side (DF745)

(745 x 396mm)

Modesty (DF748)

(715 x 243mm)

Rail (DF753)

(715 x 97mm)

Divider (DF887)

(128 x 376mm)

Drawer Front (DF888)

(344 x 122mm) x 2

Top (DF1348)

(745 x 396mm)

Right Side (DF746)

(745 x 396mm)

7

5 6

8

Left Drawer Side (W320-95LH)

(320 x 95mm) x 2

Drawer Base (T328-317)

(328 x 317mm) x 2

Right Drawer Side (W320-95RH)

(320 x 95mm) x 2

9

Drawer Back (W317-95)

(317 x 95mm) x 2

10

11

Stool Base (D0997A)

(400 x 348mm)

Stool Rail (D0998A)

(400 x 144mm) x 2

Stool Side (D0996A)

(451 x 352mm) x 2

Seat Pad (FMANPAD)

(398 x 348mm)

12 13 14 15

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 11

B

Metal dowel (F901) x 28

C

D E F

G H I

L

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

M

J K

9mm Screw (F74) x 4

9mm Screw (F73) x 8

Drawer runner (F1004) x 4

Electric drill (do not use for fitting screws)

Knock-in Peg (F171) x 8

13mm Screw (F79) x 1

Small locking nut (F3) x 4

Large locking nut (F900) x 24

Bracket (F327) x 1

Handle (F315) x 2

25mm Screw (F95) x 4

O

Plastic Nail (F91) x 8

N

Wedgefix (F639) x 4

25mm Screw (F50) x 4

7

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

B

E

8

9

Step 2

Prepare the 2 drawer fronts

Screw 2 metal dowels into each of the 2 drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

B

7

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

E

8

9

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

8 9

7

E

8 9

8

9

B

7

x 2

Assembly Instructions

5

Step 4

C

Fit the drawer bases

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer backs

Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

11

8 9

7

10

8 9

11

10

C

Attach the handles

Attach a handle to each drawer front using 2 screws .

Note: Do not overtighten the screw.

L

F

7

8 9

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

N

C

N

11

8

10

8

9

11

9

7

F

L

x 2

Prepare the left side

a: Place a runner on

the left side . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the left side .

c: Screw 5 metal

dowels into the left side .

Finished

front edge

Assembly Instructions

6

Step 8

Profiled

front edge

J

M

J

M

a:

b:

c:

1

J

B

1

Finished

front edge

Finished

front edge

J

B

1

B

J

M

Assembly Instructions

7

Step 9

Prepare the right side

a: Place a runner on

the right side . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole on the right side .

c: Screw 5 metal

dowels into the right side .

2

J

M

2

B

2

a:

b:

c:

J

Finished

front edge

Finished

front edge

Finished

front edge

J

M

J

M

B

Finished

front edge

2

Finished

front edge

Finished

front edge

A

Prepare the top

Tap 2 wooden dowels into the top .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Screw 2 metal dowels into the top .

Insert 4 large locking nuts into the top .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Assembly Instructions

8

Step 10

D

10mm

A

D

B

A

3

B

D

3

Finished

front edge

Fit the top

Push the top onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the right side .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

2

3

D

2

B

D

Step 11

2

3

A

Finished

front edge

Assembly Instructions

9

Step 12

Finished

front edge

Prepare the divider

a: Place a runner on

the divider as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the divider .

Tap a wooden dowel into the divider .

Insert 2 large locking nuts into the divider . .

Turn the divider over

c: Place a runner on

the divider as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

d: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the divider .

6

J

D

6

M

6

J

6

M

c: d:

Note: Due to the manufacturing process, the 2 holes for

the large locking nut can be on either surface of the divider.

Turn the divider over

Finished

front edge

J

M

Finished

front edge

J

M

J

M

J

D

Finished

front edge

Finished

front edge

J

M

J

6 6

A

Finished

front edge

A

Finished

front edge

Assembly Instructions

10

Step 13

Step 14

3

Fit the divider

Push the divider onto the top .

Use a screwdriver to tighten the 2 large locking nuts fitted to the divider .

3

6

D

6

Prepare the rail

Tap 2 wooden dowels into the rail .

Insert 2 large locking nuts into the rail .

Step 15

A

5

D

5

Finished

front edge

D

A

Fit the rail

Push the rail onto the right side .

Use a screwdriver to tighten the large locking nut fitted to the rail .

2

5

D

5

2

Note: The large locking nuts can

be on either surface of the divider.

Assembly Instructions

9

Step 16

Prepare the modesty

Insert 4 arge locking nuts into the modesty . .

D

4

D

4

2

Step 17

Fit the rail

Push the modesty onto the right side .

Use a screwdriver to tighten the large locking nut fitted to the modesty .

2

4

D

4

Step 18

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the 5 large locking nuts fitted to the top , modesty and rail .

1

D

3 4

5

4

1

3

5