Argos ZSVO2R-W-AR ASSEMBLY INSTRUCTIONS

Assembly Instructions - Please keep for future reference

MADE IN

BRITAIN

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number)

Important - Please read these instructions fully before starting assembly

Dimensions

Width - 69.5cm

Depth - 49.5cm

Height - 175.5cm

Seville - 2 Door Robe

Issue 1 - 08/10/13

166/8843

187/8633

144/6508

157/4803

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 40kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

Top (D2482A)

(663 x 495mm)

Base (D2485A)

(663 x 480mm)

Plinth (D2486A)

(663 x 80mm)

Door (D2487A)

(1652 x 327mm) x 2

Back (X1666-689)

(1666 x 689mm)

Left Side (D2483A)

(1753 x 496mm)

Right Side (D2484A)

(1753 x 496mm)

Hanging Rail (FHR653)

(653mm long)

Rule

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Tools required

Rule

ScissorsSquare

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Step ladder

Ruler - Use this ruler to help correctly identify the screws

Electric drill (only use when drilling into walls)

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

Wooden dowel (F22) x 6

B C

D E F

G H I

Nail (F51) x 32 40mm Screw (F910) x 10

J K

Bracket (F327) x 1

13mm Screw (F79) x 1

Hinge plate (F523) x 6

Hinge (F522) x 6

13mm Screw (F63) x 14

Rail holder

(F1014) x 2

Handle (F300) x 2

25mm Screw (F95) x 2

Step 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

Finished

front edge

Step 2

Prepare the left side

Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .

Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

Prepare the right side

Push a rail holder into the right side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .

Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

Step 3

10mm

Prepare the top and base

Tap 2 wooden dowels into the top .

Tap 2 wooden dowels into the base .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Finished

front edge

plain chipboard surface

Finished

front edge

Finished

front edge

Finished

front edge

Assembly Instructions

Step 4

Step 5

Fit the top and the base to the right side

Push the top and the base onto the right side and secure them using 4 screws .

Prepare the plinth

Tap 2 wooden dowels into the plinth .

Step 6

Fit the plinth

Push the plinth onto the right side and secure it using screw .

Plain chipboard

Note: Support the plinth until the left side has been fitted in the next step.

plain chipboard surface

Finished

front edge

Assembly Instructions

Step 7

Fit the left side

Push the left side onto the assembly and secure it using 5 screws . .

Step 8

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the outside edges of the back .

Note: Nails should be spaced about 150mm apart.

Stand the unit up for the next step.

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

Assembly Instructions

Step 9

Step 10

Fit the hanging rail

Push hanging rail into the rail holders fitted to the side panels.

Prepare the 2 doors

Push fit 3 hinges into each of the the doors

Secure each hinge with 2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.

x 2

Assembly Instructions

Step 11

Fit doors and handles

Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinges.

a: Push the hinge

onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.

b: Keep the hinge

FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.

c: The hinge must be

flat against the hinge plate prior to any adjustment.

d: The hinge must

NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.

e: Attach a handle to

each door using screw .

a: b:

c: d:

Assembly Instructions

Step 12

Adjust the doors if needed

a: Before adjusting the

doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.

b: Height adjustment.

Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.

c: Forward and Back

adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.

d: Sideways

adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.

Assembly Instructions

11 ALR2906

Step 13

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number and the reference numbers on the component pages)

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Top of Unit

WALL

Back of Unit

Fit the bracket

To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket fitted to the top of the unit.

Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back of the unit to the wall.

Fix the bracket loosely onto the top of the unit using screw and mark the wall for the wall fixing.

Swivel the bracket away from the wall and drill a hole in the wall using a suitable drill bit and fit your wall fixing.

Swivel the bracket back and fix the bracket to the wall, then tighten Screw .

Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

Warning: The unit is heavy. Lift with care.

Assembly is complete

+ 25 hidden pages