Argos ZSV5D-W-AR ASSEMBLY INSTRUCTIONS

Assembly Instructions - Please keep for future reference

Issue 1 - 02/10/13

MADE IN

BRITAIN

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: [e-mail] (quoting your original order number)

Important - Please read these instructions fully before starting assembly

Dimensions

Seville - 5 Drawer Chest

184/9198

145/0862

184/8319

189/6385

Width - 66cm

Depth - 33cm

Height - 91cm

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 21kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

1

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.

• Dispose of all packaging
carefully and responsibly.

2

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email:
[e-mail] (quoting your original order number

and the reference numbers below)

1

2

Top (D2488A)

(627 x 327mm)

Plinth (D2491A)

(627 x 80mm)

Drawer Front (D2492A)

(623 x 157mm) x 5

4

3

8

5

Back (X653-648)

(653 x 648mm)

Left Side (D2503A)

(896 x 328mm)

Right Side (D2504A)

(896 x 328mm)

Drawer Base (TSAV)

(299 x 608mm) x 5

7

6

Drawer Wrap (WSAV)

(1221 x 95mm) x 5

3

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Tools required

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Ruler - Use this ruler to help correctly identify the screws

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email:
[e-mail] (quoting your original order number

and the reference numbers below)

A

Wooden dowel (F22) x 4

B

Metal dowel (F901) x 10

C

D E F

G

Small locking
nut (F3) x 10

Nail (F51) x 15

40mm Screw (F910) x 6

Handle (F300) x 10

H

J

R (F601)

L (F600)

F599

F599

Drawer stops (F599) x 10
Runners (F600) x 5 and (F601) x 5

25mm Screw (F95) x 10

Bracket (F327) x 1

I

13mm Screw (F79) x 1

Rule Scissors Hammer

Eye protection
(when using a
hammer or drill)

Cross-head
screwdriver

Electric drill
(do not use for
fitting screws)

4

Step 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email:
[e-mail] (quoting your original order number

and the reference numbers below)

x 5

B

B

B

5

x 5

Prepare the drawer
fronts

Screw 2 metal dowels
into each of the drawer
fronts .

Note: Tighten the metal
dowels up fully against
the panel.

B

5

6

C

6

C

C

x 5

Fit the drawer base

Place the drawer base
into the narrow slot on
the drawer wrap .
Fold the wrap around the
drawer base.

7

7

6

6

Step 3

Prepare the drawer
wraps

Insert 2 small locking
nuts into each of the
drawer wraps .

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

Step 2

C

6

Note: Due to the manufacturing
process, the holes for the
locking nut can be on either
surface of the drawer wrap.

Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.

Plain chipboard

surface

Assembly Instructions

5

Step 4

Attach the handles

Attach 2 handles to
each of the 5 drawer
fronts using 2
screws .

Note: Do not
overtighten the screws.

G

E

Step 6

Step 5

x 5

5

G

E

G

E

Attach the drawer
stops

Carefully break off 2
drawer stops (F599) from
a set of drawer runners
. .

Push the drawer stops
fully through the drawer
wrap from the inside.

J

6

F599

J

F599

J

x 5

SNAP!

SNAP!

F599

J

J

F599

J

x 5

Fit the drawer front

Turn drawer wrap
assembly over and push
it onto the back of the
drawer front .

Note: Turn the locking
nuts clockwise to
secure the panels - more
than 1/2 a turn.

6

C

5

6

6

6

B

B

C

5

5

5

Assembly Instructions

6

Step 7

Prepare the right side

Push fit 5 right runners
marked ‘R’ into the right
side .

Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.

J

2

Step 8

Step 9

R

J

J

J

J

J

Finished

front edge

2

F601

J

Finished

front edge

Prepare the left side

Separate the runners .

Push fit 5 left runners
marked ‘L’ into the left
side .

Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.

J

J

1

L

F600

J

J

J

J

J

J

1

Finished

front edge

A

A

Prepare the top

Tap 2 wooden dowels
into the top .

Fix the bracket in the
middle of the top ,
flush to the back edge
using screw .

A

3

plain chipboard surface

3

F

I

I

F

I

3

Assembly Instructions

7

Finished

front edge

D

D

Step 10

Join the top to the
right side

Push the top onto
the right side and
secure with 2 screws .

Step 11

3

2

D

3

2

Prepare the plinth

Tap 2 wooden dowels
into the plinth .

A

4

A

A

plain chipboard surface

4

Finished

front edge

D

Assembly Instructions

8

Step 12

Join the plinth to the
right side

Push the plinth onto
the right side and
secure with screw .

4

2

D

Fit the left side

Push the left side
onto the assembly and
secure with 3 screws .

Step 13

1

D

4

Support the plinth

until the left side

has been fitted in

the next step.

2

D

D

D

1

Assembly Instructions

9

Step 14

y

Fit the back

a: Square up the unit by

making sure that
measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the 3
edges of the back ,
as shown.

Note: Nails should
be spaced about 150mm
apart.

Stand the unit up for
the next step.

8

H

8

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

y

y

x

x

b:

H

8

Warning: The
unit is heavy.
Lift with care.

Assembly Instructions

10

Step 15

I

Secure unit to a wall

To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by use of the metal
bracket fitted to the
top .

Fixings are not supplied
as they will need to suit
the wall type, and the
length of screw will
depend on the distance
of the back of the unit to
the wall.

Warning: Take

care when
drilling the wall that you
do not drill into any
pipes, wires etc. If in
doubt, consult an expert.

3

WALL

WALL

Top of unit

I

I

3