Argos ZSV3D-NW-AR ASSEMBLY INSTRUCTIONS

Page 1
Assembly Instructions - Please keep for future reference
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number)
Dimensions
Width - 66cm
Depth - 33cm
Height - 58cm
Seville - 3 Drawer Chest
Issue 2 - 25/03/14
151/3297
170/2187
166/5413
161/7739
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 14kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Page 3
2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
1 2
Top (D2488A)
(627 x 327mm)
Plinth (D2491A)
(627 x 80mm)
Drawer Front (D2492A)
(623 x 157mm) x 3
Drawer Base White : TSAV(T608-299)
(608 x 299mm) x 3
Back (X328-653)
(328 x 653mm)
Left Side (D2489A)
(576 x 328mm)
4
Right Side (D2490A)
(576 x 328mm)
3
7 8
6
5
Drawer Wrap (WSAV)
(1221 x 95mm) x 3
Page 4
3
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 6
C
D E F
G
Small locking nut (F3) x 6
Nail (F51) x 1540mm Screw (F910) x 6
Handle (F300) x 6
H
R (F601)
L (F600)
F599
F599
Drawer stops (F599) x 6 Runners (F600) x 3 and (F601) x 3
25mm Screw (F95) x 6
Page 5
4
Step 1
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
x 3
B
B
B
5
x 3
Prepare the drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panel.
B
5
6
C
6
C
C
x 3
Fit the drawer base
Place the drawer base into the narrow slot on the drawer wrap . Fold the wrap around the drawer base.
7
7
6
6
Step 3
Prepare the drawer wraps
Insert 2 small locking nuts into each of the drawer wraps .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 2
C
6
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer wrap.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
Plain chipboard
surface
Page 6
Assembly Instructions
5
Step 4
Attach the handles
Attach 2 handles to each of the 3 drawer fronts using 2 screws .
Note: Do not overtighten the screws.
G
E
Step 6
Step 5
x 3
5
G
E
G
E
Attach the drawer stops
Carefully break off 2 drawer stops (F599) from a set of drawer runners . .
Push the drawer stops fully through the drawer wrap from the inside.
H
6
F599
H
F599
H
x 3
SNAP!
SNAP!
F599
H
H
F599
H
x 3
Fit the drawer front
Turn drawer wrap assembly over and push it onto the back of the drawer front .
Note: Turn the locking nuts clockwise to secure the panels - more than 1/2 a turn.
6
C
5
6
6
6
B
B
C
5
5
5
Page 7
Finished
front edge
Assembly Instructions
6
Step 7
Prepare the left side
Separate the runners .
Push fit the 3 left runners . marked ‘L’ into the left side .
Note: Runners must be be fitted flat against the panel. If necessary gently tap into final position.
H
H
1
Prepare the right side
Push fit the 3 right runners marked ‘R’ into the right side .
Note: Runners must be be fitted flat against the panel. If necessary gently tap into final position.
I
2
Step 8
L
F600
H
H
H
H
1
R
F601
I
I
I
I
2
Finished
front edge
Finished
front edge
A
A
Prepare the top
Tap 2 wooden dowels into the top .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
A
3
plain chipboard surface
3
Step 9
10mm
A
Page 8
Finished
front edge
D
D
Assembly Instructions
7
Step 10
Join the top to the right side
Push the top onto the right side and secure with 2 screws .
Step 11
3
2
D
3
2
Prepare the plinth
Tap 2 wooden dowels into the plinth .
Step 12
A
4
A
A
plain chipboard surface
4
Finished
front edge
D
Join the plinth to the right side
Push the plinth onto the right side and secure with screw .
4
2
D
4
2
Support the plinth
until the left side
has been fitted in
the next step.
Page 9
Assembly Instructions
8
Step 13
Step 14
4
Fit the left side
Push the left side onto the assembly and secure with 3 screws .
D
D
1
D
D
1
y
y
x
b:
F
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the 3 edges of the back as shown.
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
8
F
8
x
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
8
Page 10
Assembly Instructions
9
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number and the reference numbers on the component pages)
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 15
Insert the drawers
Lift the front of the drawers whilst inserting to overcome the ‘stop’ system.
Note: To ensure that your drawers run smoothly, spray a small amount of furniture polish into the grooves.
Assembly is complete
Page 11
Page 12
ALR2907
Page 13
Assembly Instructions - Please keep for future reference
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number)
Important - Please read these instructions fully before starting assembly
Dimensions
Width - 66cm
Depth - 33cm
Height - 58cm
Seville - 3 Drawer Chest
Issue 3 - 26/03/15
151/3297
170/2187
166/5413
Page 14
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 14kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Page 15
2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
1 2
Top (D2488A)
(627 x 327mm)
Plinth (D2491B)
(627 x 80mm)
Drawer Front (D2492A)
(623 x 157mm) x 3
Drawer Base White : TSAV(T608-299)
(608 x 299mm) x 3
Back (X328-653)
(328 x 653mm)
Left Side (D2489A)
(576 x 328mm)
4
Right Side (D2490A)
(576 x 328mm)
3
7 8
6
5
Drawer Wrap (WSAV)
(1221 x 95mm) x 3
Page 16
3
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 6
C
D E F
G
Small locking nut (F3) x 6
Nail (F51) x 1540mm Screw (F910) x 6
Handle (F300) x 6
H
R (F601)
L (F600)
F599
F599
Drawer stops (F599) x 6 Runners (F600) x 3 and (F601) x 3
25mm Screw (F95) x 6
Page 17
4
Step 1
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
x 3
B
B
B
5
x 3
Prepare the drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panel.
B
5
6
C
6
C
C
x 3
Fit the drawer base
Place the drawer base into the narrow slot on the drawer wrap . Fold the wrap around the drawer base.
7
7
6
6
Step 3
Prepare the drawer wraps
Insert 2 small locking nuts into each of the drawer wraps .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 2
C
6
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer wrap.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
Plain chipboard
surface
Page 18
Assembly Instructions
5
Step 4
Attach the handles
Attach 2 handles to each of the 3 drawer fronts using 2 screws .
Note: Do not overtighten the screws.
G
E
Step 6
Step 5
x 3
5
G
E
G
E
Attach the drawer stops
Carefully break off 2 drawer stops (F599) from a set of drawer runners . .
Push the drawer stops fully through the drawer wrap from the inside.
H
6
F599
H
F599
H
x 3
SNAP!
SNAP!
F599
H
H
F599
H
x 3
Fit the drawer front
Turn drawer wrap assembly over and push it onto the back of the drawer front .
Note: Turn the locking nuts clockwise to secure the panels - more than 1/2 a turn.
6
C
5
6
6
6
B
B
C
5
5
5
Page 19
Finished
front edge
Assembly Instructions
6
Step 7
Prepare the left side
Separate the runners .
Push fit the 3 left runners . marked ‘L’ into the left side .
Note: Runners must be be fitted flat against the panel. If necessary gently tap into final position.
H
H
1
Prepare the right side
Push fit the 3 right runners marked ‘R’ into the right side .
Note: Runners must be be fitted flat against the panel. If necessary gently tap into final position.
I
2
Step 8
L
F600
H
H
H
H
1
R
F601
I
I
I
I
2
Finished
front edge
Finished
front edge
A
A
Prepare the top
Tap 2 wooden dowels into the top .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
A
3
plain chipboard surface
3
Step 9
10mm
A
Page 20
Finished
front edge
D
D
Assembly Instructions
7
Step 10
Join the top to the right side
Push the top onto the right side and secure with 2 screws .
Step 11
3
2
D
3
2
Prepare the plinth
Tap 2 wooden dowels into the plinth .
Step 12
A
4
A
A
plain chipboard surface
4
Finished
front edge
D
Join the plinth to the right side
Push the plinth onto the right side and secure with screw .
4
2
D
2
Support the plinth
until the left side
has been fitted in
the next step.
plain chipboard surface
4
Page 21
Assembly Instructions
8
Step 13
Step 14
4
Fit the left side
Push the left side onto the assembly and secure with 3 screws .
D
D
1
D
D
1
y
y
x
b:
F
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the 3 edges of the back as shown.
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
8
F
8
x
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
8
Page 22
Assembly Instructions
9
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number and the reference numbers on the component pages)
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 15
Insert the drawers
Lift the front of the drawers whilst inserting to overcome the ‘stop’ system.
Note: To ensure that your drawers run smoothly, spray a small amount of furniture polish into the grooves.
Assembly is complete
Page 23
Page 24
ALR2907
Loading...