Page 1
Square + 4 x 2
Assembly Instructions - Please keep for future reference
hygena
620/2493
616/6182
617/4260
622/9919
WARNING!
In order to prevent overturning, this product must be
used with the 2 wall attachment devices provided
Dimensions
Width - 75.9cm
Depth - 39.1cm
Height - 145.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
MADE IN
BRITAIN
Issue 1 - 28/11/16
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 35kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
Care and maintenance
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: To prevent
possible overbalancing this unit
must be secured to a wall
using the 2 overbalance
protector kits supplied or, an
alternative fixing method of
your choice.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
When applicable, remove any protective film
from the panels before they are used
1 Top/Base
(75.9 x 39.1cm)
2 End Panel
(138.5 x 39.1cm)
(DF8709)
x 2
(DF8714)
x 2
3 Shelf Panel
(68.5 x 38.7cm)
(DF8711)
x 3
4 Divider
(33.5 x 38.3cm)
(DF8712)
x 4
2
Page 4
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Large wooden dowel
D
Felt pad (F433) x 4
Tools required
(F40) x 44
B
Metal dowel
E
Overbalance protector
kit (
(F649) x 8
F474) x 2
C
Minifix nut (F650) x 8
Rule Scissors Hammer
Cross-head
screwdriver
Eye protection
(when using a
hammer or drill)
Electric drill
(do not use for
fitting screws)
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
3
Page 5
Assembly Instructions
Step 1
Prepare the 2 end
panels
Insert 4 minifix nuts
into both of the end
panels .
Note: The arrow on the
minifix nuts must point
towards the hole in the
edge of the panel.
2
C
Step 2
Prepare the 3 shelves
Gently tap 8 long
wooden dowels into
each shelf until they
‘’bottom out’’.
A
3
C
C
C
x 2
2
C
A
A
A
A
3
x 3
C
Step 3
Fit 2 shelves to an
end panel
Push 2 of the shelves
down onto an end panel
. .
2
Now carefully lay the
unit onto its side.
3
A
A
A
A
3
3
2
4
Page 6
Assembly Instructions
Step 4
Fit a divider
A
A
Position a divider
between the 2 shelves .
4
3
Gently tap 4 long
wooden dowels
A
through the holes in each
shelf and into the
divider until they
3
4
‘’bottom out’’.
Step 5
Fit another divider
Carefully turn the unit
back onto its end
panel.
Push a divider onto
the shelf .
Note: Support this
divider until the final shelf
has been fitted in the
next step.
4
3
Warning: The
unit is heavy.
Lift with care.
A
A
4
A
A
A
A
3
3
3
4
Step 6
Fit the final shelf
Push the shelf down
onto the end panel .
Gently tap 4 long
wooden dowels
through the holes in the
shelf and into the
divider until they
3
4
‘’bottom out’’.
5
3
A
2
4
3
A
A
A
A
2
Page 7
Assembly Instructions
Step 7
Fit the remaining end
panel
Push the remaining end
panel down onto the
3 shelves .
2
3
Step 8
Fit a divider
Carefully stand the
unit upright.
3
Warning: The
unit is heavy.
Lift with care.
A
A
2
3
3
A
A
Push a divider down
onto the shelf .
4
3
Gently tap 4 long
wooden dowels into
the divider until they
A
4
‘’bottom out’’.
4
3
6
Page 8
Assembly Instructions
Step 9
Prepare the base
panel
Stick a felt pad into
each corner of the base
panel .
1
Turn the base over
Screw 4 metal dowels
into the base panel .
Note: Tighten the metal
dowels up fully against
the panels.
D
B
1
D
D
D
1
D
B
Turn the
B
B
1
base over
B
B
Step 10
Fit the base panel
Push the base down
onto the assembly.
Use a screwdriver to
tighten the 2 minifix nuts
. fitted to each of the
C
end panels .
Note: Turn the minifix
nuts as far as they will
C
go - more than 1/2 a
turn.
1
2
B
1
C
2
2
7
Page 9
Assembly Instructions
Step 11
Fit the final divider
Carefully turn the unit
over.
Push a divider down
onto the shelf .
Gently tap 4 long
wooden dowels into
the divider until they
‘’bottom out’’.
4
3
A
4
Warning: The
unit is heavy.
Lift with care.
A
A
A
A
4
3
Step 12
Prepare the top panel
Screw 4 metal dowels
into the top panel .
B
1
B
B
B
B
1
8
Page 10
Assembly Instructions
Step 13
Fit the top panel
Push the top down
onto the assembly.
Use a screwdriver to
tighten the 2 minifix nuts
. fitted to each of the
C
end panels .
1
2
1
2
2
9
Page 11
Assembly Instructions
Step 14
Fit the 2 overbalance
protector kits
Important: A bracket
must be fitted on both
sides of the unit and they
must be at least 25mm in
from the end panels.
To prevent possible
overbalancing this unit
must be secured to a
suitable wall by fitting of
the 2 overbalance
protector kits to the
unit, or an alternative
fixing method of your
choice.
E
In order to prevent overturning
this product must be used with the
2 wall attachment devices provided
WARNING!
x 2
Underside
of top
E
25mm
Wall fixings are not
supplied as they will
need to suit the wall
type.
Take care when
Note:
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Assembly is complete
10
Page 12
Assembly Instructions
Step 15
If required, fit your
door or drawer inserts
If you have purchased
door or drawer inserts,
please refer to the
assembly instructions
packed with them.
Door
Insert
Drawer
Insert
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
11 ALR3368
Loading...