Argos ZSPA13R-BLKBLK-AR, ZSPA13R-WAU-AR, ZSPA13R-WHWH-AR ASSEMBLY INSTRUCTIONS
MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Assembly Instructions - Please keep for future reference
408/5935
397/9468
425/5954
Issue 1 - 10/06/15
Sparkle - 1 Drawer 3 Door Robe
Width - 105.1cm
Depth - 51.6cm
Height - 182.3cm
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 72kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Drawer Front (DF3872)
(69.3 x 16.2cm)
Drawer Base (T647-367)
(64.7 x 36.7cm)
Drawer Back (W636-124)
(63.6 x 12.4cm)
Left Drawer
Side (W370-124LH)
(37 x 12.4cm)
Right Drawer
Side (W370-124RH)
(37 x 12.4cm)
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
1
2 3 4
5
Top (DF3844)
(105.1 x 51.6cm)
6 7
Base (DF3846)
(101.7 x 49.3cm)
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
2
8
9 10
15
Shelf (DF3848)
(33.3 x 45cm) x 3
Large Rail (DF3840)
(66.9 x 8cm)
Right Side (DF3838)
(180.8 x 49.4cm)
13
Small Rail (DF4400)
(33.3 x 8cm)
Large Back
(X1739-688)
(173.9 x 68.8cm)
Small Back
(X1739-352)
(173.9 x 35.2cm)
12
14
Plinth (DF3845)
(101.7 x 8cm)
1917
20 21
Hanging Rail (FHR663)
(66.3cm long)
16
Left Side (DF4402)
(180.8 x 49.4cm)
Divider (DF4401)
(171.25 x 49.2cm)
Horizontal (DF3871)
(66.9 x 49.1cm)
Right Door
(DF3842)
(172.4 x 34.5cm)
Left Door
(DF3870)
(155.9 x 34.5cm)
18
Middle Door
(DF4456)
(155.9 x 34.5cm)
11
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
A B
D E F
IG H
T U
Large locking
nut (F900) x 20
Metal dowel (F901) x 20
Wooden dowel (F22) x 20
X
O
Rail Holder
(F891) x 2
13mm Screw (F63) x 24
Hinge plate
(F523) x 10
Strap
Screw
Washer x 2
Overbalance protector kit (F269) x 1
Hinge (F522) x 10
25mm Screw (F50) x 12
Handle (F569) x 4
40mm Screw (F910) x 2
M
Large wooden dowel (F40) x 1
N
Double metal dowel (F566) x 1
Q
Back holder (F276) x 5
* These can also be round
P
Nail screw (F277) x 5
J
Small locking
nut (F3) x 2
C
9mm Screw (F74) x 2 9mm Screw (F73) x 4
Knock-in Peg (F171GY) x 4
R
W
V
LK
Nail (F51) x 40
Plastic Nail (F91) x 4
Shelf stud (F110) x 12
S
Drawer runner (F1004) x 2
Wedgefix (F639) x 4
Scissors / Rule / Square / Spirit level / Hammer / Cross-head screwdriver
Eye protection / Electric drill / Step ladder
Tools required
1
Assembly Instructions
4
Step 1
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A
C
C
C
2
3
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
A
1
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
C
2
3
A
A
1
A
C
Step 3
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking nuts
clockwise to secure panels more than 1/2 a turn.
2
3
1
C
2
3
2
3
1
Assembly Instructions
5
Step 4
J
J
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
5
2 3
1
4
2 3
5
4
4
J
Attach the handles
Attach a handle to the
drawer front using 3
screws .
Note: Do not
overtighten the screw.
W
E
1
2 3
Step 7
Fit the wedgefixes
Turn the drawer
assembly over and slide
4 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
S
J
J
S
S
S
S
S
5
2
3
5
2
3
4
E
E
E
W
1
Finished
front edge
Assembly Instructions
6
Step 8
Prepare the left side
a: Place a runner on
the left side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
8
H
H
8
V
V
a:
b:
H
V
Finished
front edge
H
V
H
8
8
Finished
front edge
Finished
front edge
I
I
Assembly Instructions
7
Step 9
Finish preparing the
left side
a: Screw 6 metal
dowels into the left
side .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the
left side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
b: To fit the rail holder
screw through the top
hole with screw and
into the mark hole drilled
in the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
Fit 3 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
A
8
8
I
8
A
F
O
F
O
F
F
O
10mm
I
A
A
A
A
A
B
B
B
T
T
T
T
B
O
F
8
F
T
8
8
8
b:
a:
A
Loading...