Argos ZNSD2R2-TB-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 70.5cm

Depth - 50cm

Height - 172cm

New Sywell - 2 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 5 - 21/07/14

Important - Please read these instructions fully before starting assembly

282/4150

267/7606

266/2965

281/8960

266/3768

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 40.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Top (D2559A)

(674 x 494mm)

Left Side (D2560A)

(1711 x 496mm)

Base (D2562A)

(674 x 494mm)

Right Side (D2561A)

(1711 x 496mm)

Door (D2563A)

(1650 x 333mm) x 2

Rail (D2597A)

(674 x 125mm)

Back (X1682-700)

(1682 x 700mm)

2

3

4

7

5

Hanging Rail (FHR666)

(666mm long)

6

8

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A B C

D E F

G H

Rule

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J K L

Bracket (F327) x 1

Hinge plate (F523) x 6

Hinge (F522) x 6

Tools required

Rule

ScissorsSquare

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Step ladder

Ruler - Use this ruler to help correctly identify the screws

13mm Screw (F79) x 1 13mm Screw (F63) x 16

I

Electric drill (only use when drilling into walls)

Large locking

nut (F900) x 10

Wooden dowel (F22) x 10

Metal dowel (F901) x 10

25mm Screw (F95) x 4

Rail Holder (F891) x 2

Nail (F51) x 32

M

Handle (F315) x 2

Shelf stud (F110) x 2

N

Plastic Nail (F91) x 4

Finished

front edge

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Prepare the left side

Screw 5 metal dowels into the left side .

Note: Tighten the metal dowels up fully against the panels.

Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the left side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

B

1

Step 1

Step 2

K

B

F

I

F

I

F

I

F

1

K

1

I

F

1

F

I

F

B

K

Finished

front edge

Prepare the right side

Screw 5 metal dowels into the right side .

Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the right side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

B

2

K

2

I

F

2

F

2

A

Assembly Instructions

5

Step 3

Step 4

C

A

10mm

A

Prepare the top

Tap 4 wooden dowels into the top .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Insert 4 large locking nuts into the top .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

A

3

C

3

Finished

front edge

A

C

A

4

plain

chipboard

surface

Finished

front edge

Prepare the base

Tap 4 wooden dowels into the base .

Insert 4 large locking nuts into the base .

A

4

C

4

Finished

top edge

Finished

front edge

Finished

front edge

Finished

front edge

Assembly Instructions

6

Step 5

3

4

Fit the top and base to the right side

Push the top and base onto the right side .

Use a screwdriver to tighten the 4 large locking nuts fitted to the top and base.

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

3

4

2

3 4

C

B

C

Step 6

plain

chipboard

surface

C

A

Prepare the rail

Tap 2 wooden dowels into the rail .

Insert 2 large locking nuts into the rail .

Step 7

A

5

C

5

2

5

Plain chipboard

surface

Fit the rail

Push the rail onto the right side .

Use a screwdriver to tighten the large locking nut fitted to the rail .

5

2

C

5

2

Finished

top edge

5

Note: Support the rail until the left side has been fitted in the next step.

Finished

front edge

Assembly Instructions

7

Step 8

Step 9

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the 5 large locking nuts fitted to the top , base and rail .

1

C

3 4

5

1

3

4

b:

Fit the back and plastic nails

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back ,

coloured surface facing down, onto the unit as shown.

Nail around the outside edges of the back .

Note: Nails should be spaced about 150mm apart.

8

H

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

8

y

x

H

Warning: The unit is heavy. Lift with care.

8

Tap 2 plastic nails into the bottom edge of each of the sides and . .

N

1

2

N

Stand the unit up for the next stage.

1

2

N

x

N