Argos ZNS5D2-WB-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 69cm

Depth - 40cm

Height - 88.5cm

New Sywell - 5 Drawer Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 3 - 08/04/14

Important - Please read these instructions fully before starting assembly

257/7579

280/5935

282/2248

280/2110

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 28.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Top (D2546A)

(658 x 394mm)

Drawer Front (D2550A)

(654 x 162mm) x 5

2

Rail (D2549A)

(658 x 78mm) x 3

3

4

5

10

Back (X684-524)

(854 x 684mm)

Left Side (D2552A)

(883 x 396mm)

Right Side (D2555A)

(883 x 396mm)

Drawer Base (T636-327)

(636 x 367mm) x 5

Drawer Back (W625-124)

(625 x 124mm) x 5

9

6

7 8

Left Drawer Side (W370-124LH)

(370 x 124mm) x 5

Right Drawer Side (W370-124RH)

(370 x 124mm) x 5

6

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 8

B

Metal dowel (F901) x 20

C

D E F

G H I

L

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

M

J K

9mm Screw (F74) x 10 9mm Screw (F73) x 20

Drawer runner (F1004) x 10

Electric drill (do not use for fitting screws)

Knock-in Peg (F171) x 20

13mm Screw (F79) x 1

Small locking nut (F3) x 10

Large locking nut (F900) x 10

Nail (F51) x 21 Bracket (F327) x 1

Handle (F315) x 5

25mm Screw (F95) x 10

O

Plastic Nail (F91) x 4

N

Wedgefix (F639) x 20

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 5

B

Prepare the drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten the metal dowels up fully against the panels.

B

5

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: Arrow on locking nut must point towards hole in edge of panel.

E

7

8

Step 2

Step 3

B

5

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

7 8

5

E

7 8

E

x 5 x 5

x 5

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

E

B

E

Small groove

9

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

E

7

8

7

5

Assembly Instructions

5

Step 4

Step 5

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

9

7 8

5

Fit the drawer back

Fit the drawer back down onto the drawer base .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

6

9

6

C

7 8

Attach the handles

Attach a handle to each drawer front using 2 screws .

L

F

Step 6

5

x 5

9

8

5

7

6

C

5

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

N

I

9

8

7

5

L

F

5

F

N

x 5

Finished

front edge

Assembly Instructions

6

Step 8

Prepare the left side

a: Place 5 runners on

the left side . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .

Screw 5 metal dowels into the left side .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the left side .

M

1

Finished

front edge

I

M

I

B

1

M

I

1

Finished

front edge

I

M

Step 9

Prepare the right side

a: Place 5 runners on

the right side . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .

Screw 5 metal dowels into the right side .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the right side .

M

2

I

B

2

M

I

2

a:

b:

B

I

M

I

M

I

M

I

M

I

M

B

M

1

I

Finished

front edge

I

M

I

M

I

M

I

M

I

M

B

1

2

I

Finished

front edge

Finished

front edge

a:

b:

Finished

front edge

Finished

front edge

Assembly Instructions

7

Step 10

Prepare the top

Tap 2 wooden dowels into the top .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Insert 4 large locking nuts into the top .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Fix the bracket in the middle of the top , flush to the back edge using screw .

Fit the top to the right side

Push the top onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the top .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

Step 11

D

10mm

A

3

D

3

2

D

3

D

B

D

plain chipboard surface

3

A

D

A

Finished

front edge

D

G

K

G

K

3

plain chipboard surface

3

2