Argos ZNS51D2-WB-AR ASSEMBLY INSTRUCTIONS

Page 1
MADE IN
BRITAIN
Dimensions
Width - 74.5cm
Depth - 40cm
Height - 88.5cm
New Sywell - 5 Drawer 1 Door Chest
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 5 - 07/01/15
Important - Please read these instructions fully before starting assembly
259/1892
278/7589
278/1750
282/6990
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 32.5kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Page 3
Components - Panels
Please check you have all the panels listed below
2
1
2 3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
9
8
7
Drawer Front
(D2545A)
(359 x 162mm) x 5
Drawer Base (T341-367)
(342 x 367mm) x 5
11 12
Drawer Back
(W330-124)
(330 x 124mm) x 5
10
Divider (D2554A)
(828 x 393mm)
Shelf (D2558A)
(337 x 368mm)
Door (D2556A)
(822 x 333mm)
Right Side (D2553A)
(883 x 396mm)
5
Top (D2551A)
(715 x 394mm)
6
Base (D2557A)
(715 x 394mm)
Left Side (D2596A)
(883 x 396mm)
4
Back (X854-741)
(854 x 741mm)
13
Left Drawer Side
(W370-124LH)
(370 x 124mm) x 5
Right Drawer Side
(W370-124RH)
(370 x 124mm) x 5
Page 4
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 22
C
D E F
G H I
L
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
M
J K
9mm Screw (F74) x 10 9mm Screw (F73) x 20
P
Drawer runner (F1004) x 10
Electric drill (do not use for fitting screws)
Knock-in Peg (F171) x 20
13mm Screw (F79) x 1
Small locking nut (F3) x 10
Large locking nut (F900) x 12
Nail (F51) x 22
Bracket (F327) x 1
Handle (F315) x 6
13mm Screw (F63) x 4
ON
Hinge plate
(F523) x 2
Hinge (F522) x 2
Q
Shelf support (F121) x 4
25mm Screw (F95) x 12
S
Plastic Nail (F91) x 4
R
Wedgefix (F639) x 10
Page 5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 5 x 5
x 5
B
Prepare the drawer fronts
Screw 2 metal dowels into the holes shown on the back of each drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
7
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
E
9
10
Step 2
Step 3
B
B
7
Attach the drawer sides to the drawer front
Push the left drawer side . and right drawer side . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
9
10
7
E
9
10
x 5
E
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
7
E
B
B
E
Small groove
9
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
E
E
9
10
10
9
Page 6
Assembly Instructions
5
Step 4
Step 5
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
11
9 10
7
Fit the drawer back
Fit the drawer back down onto the drawer base .
Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
8
11
11
8
8
C
9 10
Attach the handles
Attach a handle to each drawer front using 2 screws .
L
F
Step 6
7
11
10
7
9
8
C
C
x 5
C
C
x 5
7
F
F
L
x 5
Step 7
Fit the wedgefixes
Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
R
R
R
R
I
x 5
11
10
9
7
Page 7
Finished
front edge
A
A
Assembly Instructions
6
Step 8
Prepare the top
Tap 2 wooden dowels into the top .
Insert 4 large locking nuts into the top .
Screw 2 metal dowels into the top .
Fix the bracket 170mm in from the side and flush to the back edge using screw .
Step 9
D
5
5
B
5
G
K
A
Prepare the base
a: Tap 4 wooden
dowels into the base . .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 4 large locking nuts into the base .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Turn the base over
b: Screw 2 metal
dowels into the base . .
D
6
6
B
6
A
Turn the base over
10mm
A
D
b:
D
D
D
D
A
A
Finished
front edge
6
Finished
front edge
6
B
B
5
170mm
D
D
D
D
B
B
G
K
A
A
plain chipboard surface
Page 8
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 10
Fit the top to the divider
Push the top onto the divider .
Use a screwdriver to tighten the 2 large locking nuts fitted to the divider .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Step 11
Finished
front edge
I
P
Prepare the divider
a: Place 5 runners on
the divider . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .
Tap 2 wooden dowels into the divider .
b: Slide the runners
back the other way and fit the 2nd screw into the corresponding hole in the divider .
Insert 4 large locking nuts into the divider .
P
3
I
A
3
P
I
3
D
3
a:
b:
B
D
5
3
D
D
3
Finished
front edge
I
P
I
P
I
P
I
P
I
P
A
A
3
I
I
I
I
I
D
D
D
D
Finished
front edge
3
3
5
Page 9
Finished
front edge
Assembly Instructions
8
Step 12
Prepare the right side
Screw 4 metal dowels into the right side .
Fit 2 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
N
2
N
2
Step 13
Fit the base
Push the base onto the divider .
Use a screwdriver to tighten the 2 large locking nuts fitted to the divider .
D
6
3
3
B
plain
chipboard
surface
6
3
Finished
front edge
N
N
B
B
B
B
2
Page 10
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 14
Step 15
Fit the right side
Push the right side onto the top and base .
Use a screwdriver to tighten the 4 large locking nuts fitted to the top and base .
2
5
6
D
5
Prepare the left side
a: Place 5 runners on
the left side . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .
Screw 4 metal dowels into the left side .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
P
1
Finished
front edge
I
P
I
B
1
P
I
1
a:
b:
2
5
6
I
P
I
P
I
P
I
P
I
P
B
B
B
B
I
I
I
I
I
1
1
Page 11
Assembly Instructions
10
Step 16
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 4 large locking nuts fitted to the top and base .
D
1
5 6
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit, as shown.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
13
M
The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y
a:
13
Step 17
5
1
6
b:
M
13
y
y
x
1 surface of the back is coloured on one half to match the unit. This needs to be facing down and be on this side of the unit.
x
Tap 2 plastic nails into the bottom edge of each of the sides and . .
S
1
2
Stand the unit up for the next step.
S
S
S
S
1
2
Page 12
Assembly Instructions
11
Step 18
Step 19
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides . and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the sides and out into the 2nd threaded hole in the runner.
Note: Do not over­tighten the screws . If they catch on the runner you may need to loosen them slightly.
H
8 9
P
P
H
2nd threaded
hole
P
H
K
Secure unit to a wall
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the metal bracket fitted to the top .
Fixings are not supplied as they will need to suit the wall type, and the length of screw will depend on the distance of the back of the unit to the wall.
Warning: Take
care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
5
H
H
8
9
K
5
WALL
WALL
K
Top of unit
Page 13
Assembly Instructions
12
Step 20
Step 21
Fit the shelf
Insert the 4 shelf studs at the required height.
Lower the shelf down onto the shelf studs .
12
Q
Q
Prepare the door
Push fit 2 hinges into the door .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
J
4
O
J
J
90
Q
x 4
O
O
J
J
4
12
Make sure that the plastic
sleeve is fully pushed
onto the shelf stud.
Q
O
Page 14
Assembly Instructions
13
Step 22
Fit door and handle
Note: The easiest way to attach the door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach the handle
to the door using 2 screws .
O
O
O
N
N
N
O
N
L
F
4
a: b:
c: d:
N
O
N
N
B
N
O
O
O
A
O
N
B
e:
4
L
4
F
F
Page 15
Assembly Instructions
14
Step 23
b:
c:
d:
a:
Adjust the door if needed
a: Before adjusting the
door, use a spirit level to check the top (or base) of the unit is level, front­to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
A
A
B
C
Page 16
Assembly Instructions
15
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR3016
Step 24
Assembly is complete
Warning: The unit is heavy. Lift with care.
Page 17
MADE IN
BRITAIN
Dimensions
Width - 74.5cm
Depth - 40cm
Height - 88.5cm
New Sywell - 5 Drawer 1 Door Chest
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 6 - 13/01/15
Important - Please read these instructions fully before starting assembly
259/1892
278/7589
278/1750
282/6990
Page 18
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 32.5kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Page 19
Components - Panels
Please check you have all the panels listed below
2
1
2 3
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
9
8
7
Drawer Front
(D2545A)
(359 x 162mm) x 5
Drawer Base (T341-367)
(342 x 367mm) x 5
11 12
Drawer Back
(W330-124)
(330 x 124mm) x 5
10
Divider (D2554A)
(828 x 393mm)
Shelf (D2558A)
(337 x 368mm)
Door (D2556A)
(822 x 333mm)
Right Side (D2553A)
(883 x 396mm)
5
Top (D2551A)
(715 x 394mm)
6
Base (D2557A)
(715 x 394mm)
Left Side (D2596A)
(883 x 396mm)
4
Back (X854-741)
(854 x 741mm)
13
Left Drawer Side
(W370-124LH)
(370 x 124mm) x 5
Right Drawer Side
(W370-124RH)
(370 x 124mm) x 5
Page 20
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 22
C
D E F
G H I
L
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
M
J K
9mm Screw (F74) x 10 9mm Screw (F73) x 20
P
Drawer runner (F1004) x 10
Electric drill (do not use for fitting screws)
Knock-in Peg (F171) x 20
Small locking nut (F3) x 10
Large locking nut (F900) x 12
Nail (F51) x 22
Handle (F315) x 6
13mm Screw (F63) x 4
ON
Hinge plate
(F523) x 2
Hinge (F522) x 2
Q
Shelf support (F121) x 4
25mm Screw (F95) x 12
Plastic Nail (F91) x 4
R
Wedgefix (F639) x 10
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Page 21
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 5 x 5
x 5
B
Prepare the drawer fronts
Screw 2 metal dowels into the holes shown on the back of each drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
7
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
E
9
10
Step 2
Step 3
B
B
7
Attach the drawer sides to the drawer front
Push the left drawer side . and right drawer side . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
9
10
7
E
9
10
x 5
E
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
7
E
B
B
E
Small groove
9
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
E
E
9
10
10
9
Page 22
Assembly Instructions
5
Step 4
Step 5
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
11
9 10
7
Fit the drawer back
Fit the drawer back down onto the drawer base .
Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
8
11
11
8
8
C
9 10
Attach the handles
Attach a handle to each drawer front using 2 screws .
L
F
Step 6
7
11
10
7
9
8
C
C
x 5
C
C
x 5
7
F
F
L
x 5
Step 7
Fit the wedgefixes
Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
J
J
J
J
I
x 5
11
10
9
7
Page 23
Finished
front edge
A
A
Assembly Instructions
6
Step 8
Prepare the top
Tap 2 wooden dowels into the top .
Insert 4 large locking nuts into the top .
Screw 2 metal dowels into the top .
Step 9
D
5
5
B
5
A
Prepare the base
a: Tap 4 wooden
dowels into the base . .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 4 large locking nuts into the base .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Turn the base over
b: Screw 2 metal
dowels into the base . .
D
6
6
B
6
A
Turn the base over
10mm
A
D
b:
D
D
D
D
A
A
Finished
front edge
6
Finished
front edge
6
B
B
5
D
D
D
D
B
B
A
A
plain chipboard surface
Page 24
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 10
Fit the top to the divider
Push the top onto the divider .
Use a screwdriver to tighten the 2 large locking nuts fitted to the divider .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Step 11
Finished
front edge
I
P
Prepare the divider
a: Place 5 runners on
the divider . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .
Tap 2 wooden dowels into the divider .
b: Slide the runners
back the other way and fit the 2nd screw into the corresponding hole in the divider .
Insert 4 large locking nuts into the divider .
P
3
I
A
3
P
I
3
D
3
a:
b:
B
D
5
3
D
D
3
Finished
front edge
I
P
I
P
I
P
I
P
I
P
A
A
3
I
I
I
I
I
D
D
D
D
Finished
front edge
3
3
5
Page 25
Finished
front edge
Assembly Instructions
8
Step 12
Prepare the right side
Screw 4 metal dowels into the right side .
Fit 2 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
N
2
N
2
Step 13
Fit the base
Push the base onto the divider .
Use a screwdriver to tighten the 2 large locking nuts fitted to the divider .
D
6
3
3
B
plain
chipboard
surface
6
3
Finished
front edge
N
N
B
B
B
B
2
Page 26
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 14
Step 15
Fit the right side
Push the right side onto the top and base .
Use a screwdriver to tighten the 4 large locking nuts fitted to the top and base .
2
5
6
D
5
Prepare the left side
a: Place 5 runners on
the left side . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .
Screw 4 metal dowels into the left side .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
P
1
Finished
front edge
I
P
I
B
1
P
I
1
a:
b:
2
5
6
I
P
I
P
I
P
I
P
I
P
B
B
B
B
I
I
I
I
I
1
1
Page 27
Assembly Instructions
10
Step 16
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 4 large locking nuts fitted to the top and base .
D
1
5 6
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit, as shown.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
13
M
The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y
a:
13
Step 17
5
1
6
b:
M
13
y
y
x
1 surface of the back is coloured on one half to match the unit. This needs to be facing down and be on this side of the unit.
x
Tap 2 plastic nails into the bottom edge of each of the sides and . .
K
1
2
Stand the unit up for the next step.
K
K
K
K
1
2
Page 28
Assembly Instructions
11
Step 18
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides . and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the sides and out into the 2nd threaded hole in the runner.
Note: Do not over­tighten the screws . If they catch on the runner you may need to loosen them slightly.
H
8 9
P
P
H
2nd threaded
hole
P
H
H
H
8
9
Fit the shelf
Insert the 4 shelf studs at the required height.
Lower the shelf down onto the shelf studs .
12
Q
Q
Q
x 4
12
Make sure that the plastic
sleeve is fully pushed
onto the shelf stud.
Q
Step 19
Page 29
Assembly Instructions
12
Step 20
Prepare the door
Push fit 2 hinges into the door .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
G
4
O
G
G
90
O
O
G
G
4
O
Page 30
Assembly Instructions
13
Step 21
Fit door and handle
Note: The easiest way to attach the door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach the handle
to the door using 2 screws .
O
O
O
N
N
N
O
N
L
F
4
a: b:
c: d:
N
O
N
N
B
N
O
O
O
A
O
N
B
e:
4
L
4
F
F
Page 31
Assembly Instructions
14
Step 22
b:
c:
d:
a:
Adjust the door if needed
a: Before adjusting the
door, use a spirit level to check the top (or base) of the unit is level, front­to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
A
A
B
C
Page 32
Assembly Instructions
15
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR3016
Step 23
Fit the overbalance protector kit
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit . to the unit, or an alternative fixing method of your choice.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
R
Attach the
strap to the unit
Attach the
strap to the wall
Wall fixing
(not supplied)
Washer
Strap
Strap
R
R
Example
Screw
(not supplied)
Washer
Screw
UNIT
Loading...