Argos ZNS51D2-OW-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 74.5cm

Depth - 40cm

Height - 88.5cm

New Sywell - 5 Drawer 1 Door Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 5 - 07/01/15

Important - Please read these instructions fully before starting assembly

259/1892

278/7589

278/1750

282/6990

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 32.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

2 3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

9

8

7

Drawer Front

(D2545A)

(359 x 162mm) x 5

Drawer Base (T341-367)

(342 x 367mm) x 5

11 12

Drawer Back

(W330-124)

(330 x 124mm) x 5

10

Divider (D2554A)

(828 x 393mm)

Shelf (D2558A)

(337 x 368mm)

Door (D2556A)

(822 x 333mm)

Right Side (D2553A)

(883 x 396mm)

5

Top (D2551A)

(715 x 394mm)

6

Base (D2557A)

(715 x 394mm)

Left Side (D2596A)

(883 x 396mm)

4

Back (X854-741)

(854 x 741mm)

13

Left Drawer Side

(W370-124LH)

(370 x 124mm) x 5

Right Drawer Side

(W370-124RH)

(370 x 124mm) x 5

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 8

B

Metal dowel (F901) x 22

C

D E F

G H I

L

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

M

J K

9mm Screw (F74) x 10 9mm Screw (F73) x 20

P

Drawer runner (F1004) x 10

Electric drill (do not use for fitting screws)

Knock-in Peg (F171) x 20

13mm Screw (F79) x 1

Small locking nut (F3) x 10

Large locking nut (F900) x 12

Nail (F51) x 22

Bracket (F327) x 1

Handle (F315) x 6

13mm Screw (F63) x 4

ON

Hinge plate

(F523) x 2

Hinge (F522) x 2

Q

Shelf support (F121) x 4

25mm Screw (F95) x 12

S

Plastic Nail (F91) x 4

R

Wedgefix (F639) x 10

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 5 x 5

x 5

B

Prepare the drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten the metal dowels up fully against the panels.

B

7

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

E

9

10

Step 2

Step 3

B

7

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

9

10

7

E

9

10

x 5

E

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

7

E

B

E

Small groove

9

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

E

9

10

9

Assembly Instructions

5

Step 4

Step 5

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

11

9 10

7

Fit the drawer back

Fit the drawer back down onto the drawer base .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

8

11

8

C

9 10

Attach the handles

Attach a handle to each drawer front using 2 screws .

L

F

Step 6

7

11

10

7

9

8

C

x 5

C

x 5

7

F

L

x 5

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

R

I

x 5

11

10

9

7

Finished

front edge

A

Assembly Instructions

6

Step 8

Prepare the top

Tap 2 wooden dowels into the top .

Insert 4 large locking nuts into the top .

Screw 2 metal dowels into the top .

Fix the bracket 170mm in from the side and flush to the back edge using screw .

Step 9

D

5

B

5

G

K

A

Prepare the base

a: Tap 4 wooden

dowels into the base . .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Insert 4 large locking nuts into the base .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Turn the base over

b: Screw 2 metal

dowels into the base . .

D

6

B

6

A

Turn the base over

10mm

A

D

b:

D

A

Finished

front edge

6

Finished

front edge

6

B

5

170mm

D

B

G

K

A

plain chipboard surface

Finished

front edge

Finished

front edge

Assembly Instructions

7

Step 10

Fit the top to the divider

Push the top onto the divider .

Use a screwdriver to tighten the 2 large locking nuts fitted to the divider .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

Step 11

Finished

front edge

I

P

Prepare the divider

a: Place 5 runners on

the divider . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .

Tap 2 wooden dowels into the divider .

b: Slide the runners

back the other way and fit the 2nd screw into the corresponding hole in the divider .

Insert 4 large locking nuts into the divider .

P

3

I

A

3

P

I

3

D

3

a:

b:

B

D

5

3

D

3

Finished

front edge

I

P

I

P

I

P

I

P

I

P

A

3

I

D

Finished

front edge

3

5

Finished

front edge

Assembly Instructions

8

Step 12

Prepare the right side

Screw 4 metal dowels into the right side .

Fit 2 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

N

2

N

2

Step 13

Fit the base

Push the base onto the divider .

Use a screwdriver to tighten the 2 large locking nuts fitted to the divider .

D

6

3

B

plain

chipboard

surface

6

3

Finished

front edge

N

B

2

Finished

front edge

Finished

front edge

Assembly Instructions

9

Step 14

Step 15

Fit the right side

Push the right side onto the top and base .

Use a screwdriver to tighten the 4 large locking nuts fitted to the top and base .

2

5

6

D

5

Prepare the left side

a: Place 5 runners on

the left side . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .

Screw 4 metal dowels into the left side .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the left side .

P

1

Finished

front edge

I

P

I

B

1

P

I

1

a:

b:

2

5

6

I

P

I

P

I

P

I

P

I

P

B

I

1