Argos ZNS43R2-OW-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 104cm

Depth - 49.5cm

Height - 171cm

New Sywell - 4 Drawer 3 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 4 - 07/10/14

Important - Please read these instructions fully before starting assembly

282/7023

258/1376

281/6096

278/9130

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 73kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

1 4

5

3

7

2

6

8

1

Drawer Front (D2575A)

(333 x 162mm) x 4

Drawer Base (T315-367)

(315 x 367mm) x 4

Drawer Back (W304-124)

(304 x 124mm) x 4

Left Drawer Side (W370-124LH)

(370 x 124mm) x 4

Right Drawer Side (W370-124RH)

(370 x 124mm) x 4

Rail (D2598A)

(322 x 125mm)

Horizontal (D2573A)

(337 x 467mm)

Shelf (D2574A)

(322 x 468mm) x 3

Components - Panels

Please check you have all the panels listed below

2

9

10

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D2560A)

(1711 x 496mm)

Right Side (D2569A)

(1711 x 496mm)

Hanging Rail (FHR666)

(666mm long)

12

Top (D2568A)

(1011 x 494mm)

Base (D2570A)

(1011 x 494mm)

Upright (D2571A)

(1656 x 468mm)

Large Door (D2563A)

(1650 x 333mm) x 2

Centre Door (D2576A)

(990 x 333mm)

Small Back (X1682-340)

(1682 x 340mm)

Large Back (X1682-694)

(1682 x 694mm)

11

13

14

15

Divider (D2572A)

(675 x 468mm)

17

16

18 19

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A

Wooden dowel (F22) x 20

B

Metal dowel (F901) x 28

C

D E F

G H I

L

M

J K

9mm Screw (F74) x 8 9mm Screw (F73) x 16

P

Drawer runner (F1004) x 8

13mm Screw (F79) x 1

Small locking nut (F3) x 8

Large locking nut (F900) x 20

Nail (F51) x 37

Bracket (F327) x 1

Handle (F315) x 7

13mm Screw (F63) x 20

ON

Hinge plate

(F523) x 8

Hinge (F522) x 8

Q

25mm Screw (F95) x 14

R

Rail Holder (F891) x 2

S

Nail screw (F277) x 5

Shelf stud (F110) x 12

V

Foot (F854) x 1

25mm Screw (F50) x 1

Knock-in Peg (F171) x 16

U X

Plastic Nail (F91) x 4

W

Wedgefix (F639) x 8

T

Back holder (F276) x 5

These can

also be round

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 4 x 4

x 4

B

Prepare the 4 drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten the metal dowels up fully against the panels.

B

1

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: Arrow on locking nut must point towards hole in edge of panel.

E

4

5

Step 2

Step 3

B

1

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

4 5

1

E

4 5

x 4

E

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

E

B

E

Small groove

9

E

4

5

1

4

Assembly Instructions

5

Step 4

Step 5

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

3

4 5

1

Fit the drawer back

Fit the drawer back down onto the drawer base .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

2

3

2

U

4 5

Attach the handles

Attach a handle to each drawer front using 2 screws .

L

F

Step 6

1

3

5

4

2

U

x 4

U

x 4

1

F

L

x 4

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

W

I

x 4

3

5

4

1

A

Assembly Instructions

6

Step 8

Prepare the upright

a: Place 4 runners on

the upright . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .

To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the upright . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the upright .

Fit 2 hinge plates onto the upright , making sure that the slot is facing towards the finished front edge.

c: Tap 4 wooden

dowels into the upright .

Screw 2 metal dowels into the upright .

Insert 4 large locking nuts into the upright .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

P

11

I

R

J

11

P

I

B

D

N

J

R

J

A

J

R

J

R

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

I

P

a:

b:

c:

J

P

11

I

11

N

A

11

10mm

A

D

B

D

Finished

front edge

Finished

front edge

Assembly Instructions

7

Step 9

Finished

front edge

I

P

I

P

I

P

I

P

I

P

I

B

D

B

D

B

A

Prepare the divider

a: Place 4 runners on

the divider . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the divider .

c: Tap 2 wooden

dowels into the divider .

Screw 2 metal dowels into the divider .

Insert 2 large locking nuts into the divider .

Turn the divider over

d: Screw a metal dowel

. into the divider .

P

15

I

P

15

I

Turn the divider over

A

B

D

15

Finished

front edge

Finished

front edge

15

B

a:

b:

c:

d:

15

Finished

front edge

Assembly Instructions

8

Step 10

A

Finished

front edge

Plain chipboard

surface

D

A

Prepare the horizontal

Tap 4 wooden dowels into the horizontal .

Insert 4 large locking nuts into the horizontal .

A

8

D

8

Finished

front edge

Finished

front edge

Step 11

Fit the horizontal to the upright

Push the horizontal onto the upright .

Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

Step 12

Fit the divider to the horizontal

Push the divider onto the horizontal .

Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .

8

11

D

15

8

D

B

D

8

11

8

15

Finished

front edge

Assembly Instructions

9

Step 13

Step 14

A

Prepare the base

a: Tap 4 wooden

dowels into the base . .

Insert 4 large locking nuts into the base .

Screw the foot into the middle of the base , 75mm in from the front edge using screw .

Turn the base over

b: Screw 4 metal

dowels into the base . .

A

14

D

14

D

C

V

A

Finished

front edge

75mm

D

Plain chipboard

surface

14

Finished

front edge

B

14

Turn the

base over

a:

b:

14

B

Fit the base

Push the base onto the upright and divider .

Use a screwdriver to tighten the 4 large locking nuts fitted to the upright and the divider .

14

11

D

14

15

11

15

11

15

Note: To make it easier to fit the top and base panels, place polystyrene blocks from the packaging underneath the upright and divider panels to raise the assembly.

V

14

C

Finished

front edge

Assembly Instructions

10

Step 15

Finished

front edge

A

D

A

D

B

Prepare the top

a: Tap 4 wooden

dowels into the top .

Insert 4 large locking nuts into the top .

Screw 2 metal dowels into the top .

A

13

D

13

B

13

Step 16

Fit the top

Push the top onto the upright .

Use a screwdriver to tighten the 2 large locking nuts fitted to the upright .

13

11

D

11

13

11

Step 17

B

N

Finished

front edge

Prepare the right side

Screw 4 metal dowels into the right side .

Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

B

10

N

10

N

Assembly Instructions

11

Step 18

Fit the right side

Push the right side onto the top and base .

Use a screwdriver to tighten the 4 large locking nuts fitted to the top and base .

Step 19

Finished

front edge

Prepare the left side

Screw 5 metal dowels into the left side .

Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the left side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

B

9

N

B

J

R

J

9

N

9

R

J

9

J

13

10

14

10

13

14

D

13

14