Argos ZNS32R-OWH-AR, ZNS32R-WABLK-AR, ZNS32R-WHBLK-AR, ZNS32R-WHPK-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

New Sywell - 3 Drawer 2 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 1 - 28/05/15

Important - Please read these instructions fully before starting assembly

411/1524

404/1340

412/3127

411/6316

Width - 70.5cm

Depth - 50cm

Height - 172cm

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 51kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Left Side (DF3319)

(171.1 x 49.6cm)

Right Side (DF3320)

(171.1 x 49.6cm)

Top (D2559A)

(67.4 x 49.4cm)

Base (D2562A)

(67.4 x 49.4cm)

Shelf (DF3326)

(67.4 x 46.8cm)

Rail (D2597A)

(67.4 x 12.5cm)

Hanging Rail (FHR666)

(66.6cm long)

Left Door (DF3325)

(115.5 x 33.3cm)

Drawer Front (DF3324)

(67 x 16.2cm) x 3

Right Door (DF3987)

(115.5 x 33.3cm)

Drawer Back (W370-124)

(64.1 x 12.4cm) x 3

Drawer Base (T652-367)

(65.2 x 36.7cm) x 3

Back (X1682-700)

(168.2 x 70cm)

Left Drawer Side (W370-124LH)

(37 x 12.4cm) x 3

Right Drawer Side (W370-124RH)

(37 x 12.4cm) x 3

9 10 11

13 14

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Wooden dowel (F22) x 14

Metal dowel (F901) x 20

D F

G H I

J K

9mm Screw (F74) x 6 9mm Screw (F73) x 12

Drawer runner (F1004) x 6

Small locking nut (F3) x 6

Large locking nut (F900) x 14

Nail (F51) x 32

Handle (F315) x 5

13mm Screw (F63) x 16

Hinge plate

(F523) x 6

Hinge (F522) x 6

25mm Screw (F95) x 10

Rail Holder (F891) x 2

Shelf stud (F110) x 2

Knock-in Peg (F171) x 12

Plastic Nail (F91) x 4

Wedgefix (F639) x 12

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

x 3

Step 2

Prepare the 3 drawer fronts

Screw 2 metal dowels into each of the drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

Attach the drawer sides to the large drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the 3 drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

Assembly Instructions

Step 4

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the large drawer back

Fit the drawer back between the drawer sides and .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

9 10

x 3

9 10

Fit the wedgefixes

Turn the large drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

Step 7

Attach the handles

Attach a handle to each drawer front using 2 screws .

+ 14 hidden pages