Argos ZNS03MR-OW-AR, ZNS03MR-TB-AR, ZNS03MR-WB-AR, ZNS03MR-WPK-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 104cm

Depth - 50cm

Height - 172cm

New Sywell - 3 Door Mirror Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 2 - 16/01/15

Important - Please read these instructions fully before starting assembly

355/9510

343/9692

323/2909

333/9259

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 67kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Rule

Tools required

Rule

ScissorsSquare

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Step ladder

Electric drill (only use when drilling into walls)

Components - Panels

Please check you have all the panels listed below

1 2 3

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Left Side (D2560A)

(1711 x 496mm)

Right Side (D2569A)

(1711 x 496mm)

Upright (D2923A)

(1656 x 468mm)

Shelf (D2574A)

(322 x 468mm) x 3

Plain Door (D2563A)

(1650 x 333mm) x 2

Top (D2568A)

(1011 x 494mm)

Base (D2922A)

(1011 x 494mm)

Small Back (X1682-340)

(1682 x 340mm)

Large Back (X1682-694)

(1682 x 694mm)

7 8

Mirror Door (D2563MA)

(1650 x 333mm) x 1

(Mirror - SG17 1647 x 300mm Safety Back SAR)

Hanging Rail (FHR666)

(666mm long)

Rail (D2597A)

(674 x 125mm)

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A B C

D E F

G H

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J K L

Hinge plate (F523) x 9

Hinge (F522) x 9

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Ruler - Use this ruler to help correctly identify the screws

13mm Screw (F63) x 22

Large locking

nut (F900) x 14

Wooden dowel (F22) x 14

Metal dowel (F901) x 14

25mm Screw (F95) x 4

Rail Holder (F891) x 2

Nail (F51) x 36

Shelf stud (F110) x 14

Nail screw (F277) x 5

Back holder (F276) x 5

* These can also be round

Plastic Nail (F91) x 4

Handle (F315) x 2

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Prepare the upright

a: Insert 4 large locking

nuts into the upright . .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Tap 4 wooden dowels into the upright .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Screw a metal dowel into the upright .

Note: Tighten the metal dowel up fully against the panel.

b: Fit 3 hinge plates

onto the upright , making sure that the slot is facing towards the finished front edge.

Fit the rail holder to the upright using 2 screws .

Step 1

Finished

front edge

10mm

Finished

front edge

+ 11 hidden pages