Argos ZNS02SR-OWH-AR, ZNS02SR-WABLK-AR, ZNS02SR-WHBLK-AR, ZNS02SR-WHPK-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 101.9cm

Depth - 59.5cm

Height - 171.1cm

New Sywell - 2 Door Sliding Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 1 - 28/05/15

Important - Please read these instructions fully before starting assembly

427/1237

425/8700

427/1770

427/1244

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 62kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 1, 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

1

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.

• Dispose of all packaging
carefully and responsibly.

Rule

Tools required

Rule

ScissorsSquare

Spirit
level

Hammer Bradawl

Eye protection
(when using a
hammer or drill)

Cross-head
screwdriver

Step
ladder

Electric drill
(only use
when drilling
into walls)

Components - Panels

Please check you have all the panels listed below

2

1

2 3

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

4

5

Left Side (DF3581)

(171.1 x 59.2cm)

Right Side (DF3582)

(171.1 x 59.2cm)

Top/Base (DF3584)

(98.9 x 59cm) x 2

Shelf (DF3587)

(48.7 x 49cm) x 2

Rail (DF3588)

(48.7 x 12cm) x 2

Divider (DF3585)

(165.6 x 49.6cm)

Door (DF3583)

(164.7 x 50.4cm) x 2

Back (X1682-506)

(168.2 x 50.6cm) x 2

6

8

9

Hanging Rail (FHR481)

(48.1cm long) x 2

7

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

A

Wooden dowel (F22) x 16

C

D E F

G

P

98.7cm Track (F221) x 4

O

Bottom glide

(F952) x 4

N

B

Metal dowel (F901) x 12

Large locking

nut (F900) x 24

Buffer bracket

(F261) x 1

Q

Top glide

(F956) x 4

M

Mushroom Head Pin (F260) x 4

Double metal dowel (F566) x 4

S

Rail Holder
(F891) x 4

H

Nail screw (F277) x 10

Back holder (F276) x 10

These can
also be round

K

J

40mm Screw (F910) x 4

13mm Screw (F63) x 18

25mm Screw (F95) x 4

R

UT

W

Handle (F315) x 2

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Large wooden dowel (F40) x 2

Feet (F854) x 2

I

Nail (F51) x 36

L

V

Plastic Nail (F91) x 4

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

25mm Screw (F50) x 2

13mm Screw (F79) x 8

A

A

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

A

O

Prepare the top and
base

Place 2 plastic tracks
down onto each of the
top and base
panels, making sure that
they are flush with the
edges of the panel.

Gently tap along the
length of the plastic
tracks until they are
fitted flat to the surface
of the panel.

Turn the top and the
base panels over

Tap 4 wooden dowels
into each of the top
and base panels.

Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.

Insert 4 large locking
nuts into each of the
top and base
panels.

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

10mm

A

4 4

O

4

4

O

O

Turn the top and

the base over

C

4 4

x 2

x 2

C

O

O

Finished

front edge

4

C

C

C

C

A

A

Finished

front edge

4

Finished

front edge

A

A

Assembly Instructions

5

Step 2

H

S

H

S

H

H

S

Turn the divider over

A

A

H

H

S

Finished

front edge

Prepare the divider

Tap 4 wooden dowels
into the divider .

Fit a rail holder by
screwing through the top
hole with screw and
into the mark hole drilled
in the divider . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.

Turn the divider over

Fit another rail holder
by screwing through the
top hole with screw
and into the mark hole
drilled in the divider .
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.

A

3

S

H

H

3

S

H

H

3

3

3

E

E

Assembly Instructions

6

Step 3

E

E

Note: The plastic

tracks must be on

the inside surfaces

of the top and base

Fit the top and base
to the divider

Attach the top and
the base to the
divider using 4
screws .

4

4

3

E

4

4

3

Top

Base

C

C

A

A

C

C

A

Prepare 1 of the
shelves

Tap 2 wooden dowels
into the shelf .

Insert 4 large locking
nuts into the shelf .

5

C

5

5

Finished

front edge

Step 4

D

R

Assembly Instructions

7

Step 5

D

5

Finished

front edge

Fit the shelf

a: Push the shelf

onto the divider .

Tap 2 double metal
dowels through the
divider and into the
shelf until they
‘’bottom out’’.

Tap 2 large wooden
dowels through the
divider and into the
shelf until they
‘’bottom out’’.

b: Use a screwdriver to

tighten the 2 large
locking nuts fitted to
the shelf .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

5

3

R

3

5

3

5

C

C

5

a:

b:

3

R

D

C

R

D

Finished

front edge

Prepare the left side

Screw 6 metal dowels
into the left side .

Note: Tighten the metal
dowels up fully against
the panels.

Fit a rail holder by
screwing through the top
hole with screw and
into the mark hole drilled
in the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.

B

1

B

B

B

B

B

B

B

H

H

S

Step 6

1

S

H

H

1

Assembly Instructions

8

Step 7

R

a:

R

3

Fit a rail

a: Tap 2 double metal

dowels through the
divider and into a rail
. until they ‘’bottom
out’’.

b: Use a screwdriver to

tighten the 2 large
locking nuts fitted to
the rail .

Note: Support the rail
until the left side has
been fitted in the next
step.

R

3

6

C

6

b:

6

Finished

front edge

Plain chipboard

surface

x 2

Prepare the 2 rails

Insert 4 large locking
nuts into each of the
2 rails .

C

6

C

C

C

C

Finished

front edge

6

Plain chipboard

surface

Step 8

Assembly Instructions

9

Step 9

6

1

5

4

4

a:

P

a:

P

Fit the left side

a: Push the left side

onto the assembly.

Tap 2 mushroom head
pins into the holes on
the outside of the left
side .

b: Use a screwdriver to

tighten the 8 large
locking nuts fitted to
the top , base ,
shelf and rail .

P

1

C

4 4

5 6

A

Prepare the other
shelf

Tap 2 wooden dowels
into the shelf .

Insert 4 large locking
nuts into the shelf .

5

C

5

A

A

C

C

C

C

5

Finished

front edge

Step 10

Assembly Instructions

10

Step 11

5

3

Fit the other shelf

Push the shelf onto
the divider .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the shelf .

C

5

5

3

Prepare the right side

Screw 6 metal dowels
into the right side .

Note: Tighten the metal
dowels up fully against
the panels.

Fit a rail holder by
screwing through the top
hole with screw and
into the mark hole drilled
in the right side .
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.

B

2

Step 12

S

H

H

2

B

H

H

S

B

B

B

B

B

2

Finished

front edge

P

a:

a:Pa:

Assembly Instructions

11

Step 13

Fit the other rail

Push the rail onto the
divider .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the rail .

Note: Support the rail
until the right side has
been fitted in the next
step.

Step 14

Finished

front edge

6

3

Plain chipboard

surface

6

6

3

C

6

Fit the right side

a: Push the right side

onto the assembly.

Tap 2 mushroom head
pins into the holes on
the outside of the right
side .

b: Use a screwdriver to

tighten the 8 large
locking nuts fitted to
the top , base ,
shelf and rail .

P

2

C

4 4

5 6

2

4

4

5

yy

yy

xx

Assembly Instructions

12

Step 15

Fit back panels

a: Square up the unit by

making sure that
measurement x:x equals

y:y.

Place the 2 backs
onto the unit, as shown.

Make sure that the 2
backs are pushed up
tight against each other
and that they meet in the
centre of the divider’s
back edge.

b: Nail around the

outside edges of the 2
backs.

Note: Do not nail where
the 2 backs meet.

c: Push the nail screws

. through the back
holders and tap them
down between the 2
backs and into the
back edge of the divider
. .

Keep tapping the nail
screws in until the
back holders dig into
the 2 backs.

9

L

J

K

9

3

J

K

Note: If ever you need to take
the backs off to dismantle the
unit, the nail screws can be
taken out using a screwdriver.

J

K

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

xx

c:

Note: These can
also be round

KJ

+

J

K

9

9

K

b:

L

9

9

Assembly Instructions

13

Step 16

Fit the 4 plastic nails

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .

Screw the 2 feet
down the middle of the
base , 1 near the front
and 1 near the back,
using screws .

Carefully stand the
unit up for the next
step.

V

1

2

V

V

V

V

1

2

Warning: The
unit is heavy.
Lift with care.

7

7

7

S

Fit the 2 hanging rails

Push the hanging rails
into the rail holders .

7

S

Step 17

U

G

U

G

U

4

4

G

Assembly Instructions

14

Step 18

Prepare the right
hand door

Important: Check that
the holes are in the same
place as the diagram.

Push 2 top glides into
1 of the doors .

Push 2 bottom glides
into the same door
and secure each one
with 2 screws .

M

N

8

8

I

N

Prepare the left hand
door

Important: Check that
the holes are in the same
place as the diagram.

Fit the buffer bracket
onto the other door using
2 screws .

Push 2 top glides into
the door .

Push 2 bottom glides
into the door and
secure each one with 2
screws .

M

N

8

8

I

Step 19

Q

H

I

I

M

M

I

I

N

I

I

N

M

M

I

I

N

I

I

N

H

Q

H

Q

This will be the
right hand door

This will be the
left hand door

Assembly Instructions

15

Step 20

Fit the doors

a: With the top of the

right hand door
leaning back at an angle,
insert the bottom glides
. into the rear track .

Push the top of the right
hand door in and
locate the top glides
into the rear track .

b: With the top of the

left hand door
leaning back at an angle,
insert the bottom glides
. into the front track .

Push the top of the left
hand door in and
locate the top glides
into the front track .

Note: For more
information about fitting
the doors please refer to
the relevent diagrams.

To fit the top of the Doors

This lug fits

into the groove

in the track.

The switch in

the top glides

must be in this

position prior to

fitting the top of

the Doors.

You may have been supplied with a

top glide that differs slightly to the

one shown. It may have a switch that

just moves up and down and does

not lock into postion.

To fit the bottom of the Doors

When the top of

the Door is in
position, press the
switch to push lug

into the groove of

the track.

Left hand door

Right hand door

8

8

N

N M M

O

N

O

O

M

8

8

O

M

Buffer bracket

a:

8

Right

hand door

b:

8

Left hand

door

Assembly Instructions

16

Step 21

Adjust the doors if
needed

If your doors are not
running smoothly, please
follow these instructions
to adjust the bottom
glides.

IF YOUR DOORS DO NOT RUN SMOOTHLY

Before adjusting the doors, use a spirit level to check the base
(or top) of the unit is level, front-to-back and side-to-side in the
3 positions shown.
Use suitable packing pieces (not supplied) to make the unit
level BEFORE making any adjustment, as shown.

To raise the door, loosen the screws and
swivel the glide towards the ‘+’ arrow.
Re-tighten the screws.

To lower the door, loosen the screws and
swivel the glide towards the ‘-’ arrow.
Re-tighten the screws.

Once the doors have been adjusted and
are running smoothly, use 2 screws to
hold each of the bottom glides in position.

H H

H

Assembly Instructions

17

Step 22

Attach the handles

Attach a handle to
each of the doors
using screws .

T

F

8

F

F

T

T

8

8

Assembly Instructions

18

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Step 23

Fit the overbalance
protector

To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of the
overbalance protector kit
. to the unit, or an
alternative fixing method
of your choice.

Wall fixings are not
supplied as they will
need to suit the wall
type.

Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.

Assembly is complete

W

W

WALL

Wall fixing

(not supplied)

Screw

(not supplied)

Washer

Strap

W

Strap

Washer

Screw

TOP OF UNIT

W

ALR3192