Argos ZNOT33MR-MW-AR, ZNOT33MR-WO-AR, ZNOT33MR-DLO-AR ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Normandy - Tall 3+3 Mirror Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 11/06/15
355/6324
357/5563
338/3267
Width - 149.5cm
Depth - 50cm
Height - 199.5cm
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 108kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Drawer Front (DF1859)
(494 x 162mm) x 3
Drawer Back (W436-124)
(436 x 124mm) x 3
Left Drawer Side (W370-124LH)
(370 x 124mm) x 3
Right Drawer Side (W370-124RH)
(370 x 124mm) x 3
Drawer Base
(T447-367)
(447 x 367mm) x 3
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1 2 3 4
5
Base (DF1969A)
(1461 x 470mm)
Top (D2047A)
(1495 x 496mm)
6
7
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Divider (DF1870)
(1883 x 469mm)
Horizontal (DF1871)
(468 x 468mm)
Small Divider (DF1872)
(489 x 469mm)
Mirror Door (DF1858A)
(1399 x 494mm)
(Mirror - SG14 1376 x 311mm Safety Back SAR)
8
9 10
11
14
21
Large Shelf (D2052A)
(965 x 467mm)
12
Back Rail (D2053A)
(965 x 120mm)
13
Plinth (D2054A)
(1461 x 80mm) x 2
Small Shelf (D2060A)
(479 x 467mm)
18
22
Plain Door (D2056A)
(1894 x 494mm) x 2
Large Hanging Rail (FHR957)
(957mm long) x 2
19
Small Hanging Rail (FHR471)
(471mm long) x 2
20
Large Back (X956)
(1914 x 988mm)
Small Back (X955)
(1914 x 499mm)
Left Side (D2048C)
(1978 x 471mm)
Right Side (D2049C)
(1978 x 471mm)
17
1615
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 14
B
Metal dowel (F901) x 26
P
K
I
O
E
Nail screw (F277) x 6
D
Large locking nut (F900) x 20
L
H
Nail (F51) x 45
N
Shelf stud (F110) x 8
G
13mm Screw (F63) x 30
M
Rail holder
(F1014) x 8
J
40mm Screw (F910) x 4
Q
Plastic Nail (F91) x 6
F
Back holder (F276) x 6
* These can also be round
C
Small locking nut (F3) x 6
Wedgefix (F639) x 6
9mm Screw (F73) x 12
9mm Screw (F74) x 6
W
Drawer runner (F1004) x 6
Knock-in Peg (F171GY) x 12
V
T
Handle screw (F461) x 12
R
Hinge plate (F523) x 11
U
Hinge (F518) x 11
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Large Handle
(FBARH224 ) x 3
S
Small Handle
(FBARHANDLE ) x 3
mm 10 20 30 40mm 10 20 30 40 50
Ruler - Use this ruler to help
correctly identify the screws
1
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 3
x 3
x 3
x 3
B
B
B
C
C
C
C
2
3
Step 2
Prepare the 3 drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
1
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
2
3
Attach the drawer sides to the drawer fronts
Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
2 3
1
C
C
2 3
B
B
1
2
3
1
Assembly Instructions
5
Step 4
L
L
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
5
2 3
1
4
2 3
5
4
4
L
2 3
Step 7
Fit the wedgefixes
Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
P
x 3
x 3
x 3
L
L
x 3
P
P
P
5
2
4
2
3
5
3
S
S
Attach the handles
Attach a small handle to each drawer front using 2 screws .
1
S
T
T
1
Assembly Instructions
6
Step 8
D
10mm
A
R
Finished
front edge
H
W
H
W
Prepare the divider
a: Place 3 runners on
the divider . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the divider .
Fit 3 hinge plates onto the divider , making sure that the slot is facing towards the finished front edge.
c: Tap 2 wooden
dowels into the divider .
Screw 3 metal dowels into the divider .
Insert 2 large locking nuts into the divider . .
W
10
H
H
10
10
10
B
A
D
10
R
10
H
H
H
a:
b:
c:
H
W
H
W
B
B
B
10
10
R
R
R
A
A
D
D
Finished
front edge
Finished
front edge
Finished
front edge
Finished
top edge
Finished
top edge
Finished
front edge
Finished
front edge
A
Assembly Instructions
7
Step 9
Step 11
Step 10
D
D
D
D
A
Finished
front edge
Prepare the horizontal
Insert 4 large locking nuts into the horizontal .
Tap 2 wooden dowels into the horizontal .
D
15
A
15
15
B
D
Fit the horizontal to the divider
Push the horizontal onto the divider .
Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
10
15
D
D
15
15
10
Finished
front edge
H
W
H
W
H
W
H
W
H
H
H
B
B
Prepare the small divider
a: Place 3 runners on
the small divider . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the small divider .
Screw 2 metal dowels into the small divider .
W
16
H
H
16
16
a:
b:
B
16
16
Finished
front edge
Assembly Instructions
8
Step 12
Fit the small divider to the horizontal
Push the small divider onto the horizontal .
Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .
15
16
D
15
15
16
Prepare the base
Insert 4 large locking nuts into the base .
Tap 2 wooden dowels into the base .
D
7
A
7
Step 13
Step 14
A
D
D
D
D
A
plain chipboard surface
7
Finished
front edge
Fit the base
Push the base onto the divider and small divider and secure with 4 screws .
16
7
10
J
7
plain chipboard surface
J
J
J
J
16
10
Finished
front edge
Assembly Instructions
9
Step 15
Step 16
Prepare the left side
Screw 5 metal dowels into the left side .
Fit 4 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.
Insert 2 large locking nuts into the left side . .
Tap a wooden dowel into the left side .
B
8
R
8
D
A
8
8
A
D
D
R
R
R
R
R
B
B
B
B
B
8
A
Prepare the right side
Screw 4 metal dowels into the right side .
Fit 4 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
Insert 2 large locking nuts into the right side .
Tap a wooden dowel into the right side .
B
9
R
9
D
A
9
9
D
D
B
B
Finished
front edge
R
9
R
R
R
R
B
B
9
Assembly Instructions
10
Step 17
Step 18
Fit the right side to the base
Push the right side onto the base .
Use a screwdriver to tighten the 2 large locking nuts fitted to the base .
9
7
7
D
A
D
A
D
plain chipboard surface
14
Prepare the 2 plinths
Insert 2 large locking nuts into each of the plinths .
Tap 2 wooden dowels into each of the plinths . .
D
14
A
14
x 2
Step 19
Finished
top edge
A
Prepare the back rail
Insert 2 large locking nuts into the back rail . .
Tap 2 wooden dowels into the back rail .
D
12
A
12
D
D
A
plain chipboard surface
12
Finished
top edge
Assembly Instructions
11
Step 20
Step 21
Fit the back rail and the plinths
Push the back rail onto the divider .
Use a screwdriver to tighten the large locking nut fitted to the back rail .
Push each plinth onto the right side .
Use a screwdriver to tighten the large locking nut fitted to each plinth .
14
9
14
D
12
10
12
D
9
plain chipboard surface
14
plain chipboard surface
14
Note: Support the back rail and plinth until the left side has been fitted in the next step.
10
plain chipboard surface
12
14
14
12
8
Fit the left side
Push the left side onto the base , back rail and the 2 plinths .
Use a screwdriver to tighten the 5 large locking nuts fitted to the base , back rail and plinths .
8
7
12
14
D
7 12
14
7
Assembly Instructions
12
Step 22
B
B
B
B
B
B
Rounded
front edge
Prepare the top
Screw 6 metal dowels into the top .
B
6
6
Step 23
Fit the top and plastic nails
Push the top onto the assembly.
Use a screwdriver to tighten the 6 large locking nuts fitted to the left side , right side and divider .
Tap 2 plastic nails into the bottom edge of each of the sides and . .
Tap 1 plastic nail into the bottom edge of each plinth . .
8
9 10
D
6
O
14
O
8
9
9
8
6
10
O
O
O
O
O
O
14
14
Assembly Instructions
13
Step 24
Fit back panels
a: Square up the unit by
making sure that measurement x:x equals
y:y.
Place the small back and large back , coloured surface facing down, onto the unit as shown.
Make sure that the 2 backs are pushed up tight against each other and that they meet in the centre of the divider’s back edge.
b: Nail around the
outside edges of the 2 backs.
Note: Do not nail where the 2 backs meet.
c: Push the nail screws
. through the back holders and tap them down between the small back and large back . and into the back edge of the divider .
Keep tapping the nail screws in until the back holders dig into the small and large back.
Stand the unit up for the next step.
21
22
K
E
F
21
22
10
E
F
Warning: The unit is heavy. Lift with care.
Note: If ever you need to take the backs off to dismantle the unit, the nail screws can be taken out using a screwdriver.
E
F
y
y
x
y
b:
K
Note: These can also be round
FE
+
21
10
22
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
x
c:
E
F
21
22
F
Assembly Instructions
14
Step 25
M
a: Fit the hanging
rails
You can fit the 2 long hanging rails and 2 short hanging rails using any of the posi­tions shown opposite.
Note: The short rail at position 4 is used for shoe storage.
Insert 2 rail holders for each of the 4 rails and then secure them with screws .
Push the hanging rails and down into the rail holders .
b: Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
G
19
20
M
19
20
M
G
x 8
x 4
19
20
M
Short Rail Position 2
Short Rail Position 3
Short Rail Position 1
Short Rail Position 4
Long Rail Position 3
Long Rail Position 1
Long Rail Position 2
I
W
W
I
2nd threaded
hole
W
I
2 3
I
I
a:
b:
Assembly Instructions
15
Step 26
Fit the shelves
Insert 4 shelf studs at position 1 or 2 for the large shelf and the small shelf .
Lower the large shelf and the small shelf down onto the shelf studs .
N
11
13
11
13
N
N
x 4
N
x 4
N
x 4
N
x 4
Small shelf Position 1
Small shelf Position 2
Large shelf Position 1
Large shelf Position 2
11
13
Step 27
Prepare the mirror door and the 2 plain doors
Push fit 3 hinges into the mirror door .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
Push fit 4 hinges into each of the plain doors . .
Secure each hinge with 2 screws .
G
U
17
90
U
U
G
G
U
G
G
U
G
G
U
G
G
18
x 2
U
G
G
U
G
G
U
G
G
Warning: Glass! Handle with care
17
G
U
18
Assembly Instructions
16
Step 28
H
Fit doors and handles
Note: The easiest way to attach each door and . is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a large handle
. to each door and . using 2 screws .
U
U
R
R
R
U
R
17
18
17
18
e:
a: b:
c: d:
R
U
R
R
B
R
U
U
U
A
U
R
B
V
T
U
18
T
T
V
V
V
17
18
Warning: Glass! Handle with care
Assembly Instructions
17
Step 29
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
18
Step 30
Fit the overbalance protector
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the overbalance protector kit . fitted to the unit or, an alternative fixing method of your choice.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Q
Strap
Washer
N
Q
Wall fixing
(not supplied)
Washer
Screw
(not supplied)
Q
Screw
Assembly Instructions
ALR308519
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 31
IMPORTANT INFORMATION ABOUT THIS PRODUCT
This product complies with the requirements of BS 7449:1991 and has been manufactured by
DECORATIVE PANELS FURNITURE LTD, TEESSIDE INDUSTRIAL ESTATE,
THORNABY-ON-TEES, CLEVELAND, TS17 9LT
.
The product code for this unit and the item code(s) for the glass components are listed in the Assembly
Instructions along with a description of the type of glass used. All clear/tinted glass complies with the requirements of BS 6206 Class A. All mirrors comply with the requirements of BS 6206 Class C. If the
glass component contained in this unit is chipped or broken consult the furniture manufacturer, retailer,
or agent with regard to obtaining a manufacturing specification and shape for replacement glass
quoting the unit description and batch number or date of manufacture.
Do not place very hot or very cold items against or in close proximity to glass surface(s) unless
adequately thick insulating material is used to prevent such items coming in contact with the glass.
Do not strike the glass with hard or pointed items.
Do not sit or stand upon horizontal glass surfaces.
When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if
necessary - do not use washing powders or any other substance containing abrasives since these
substances scratch glass.
If stated in the instruction leaflet, it is essential that this unit is fixed to a wall.
KEEP THESE INSTRUCTIONS FOR FUTURE USE
Assembly is complete
Warning: The unit is heavy. Lift with care.
Loading...