Argos ZNOT02R-MW-AR, ZNOT02R-WO-AR, ZNOT02R-DLO-AR ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 50cm
Height - 200cm
Normandy - 2 Door Tall Robe
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 6 - 03/03/15
Important - Please read these instructions fully before starting assembly
274/3750
258/2588
268/9986
357/1505
343/1023
327/8987
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 60kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Back Rail (D2053A)
(965 x 120mm)
Door (D2056A)
(1894 x 494mm) x 2
Top (D2057A)
(999 x 496mm)
Base (D2058A)
(965 x 470mm)
Plinth (D2059A)
(965 x 80mm)
2
3
4
9 10
5
6
7
Hanging Rail (FHR957)
(957mm long) x 2
8
Large Shelf (D2052A)
(965 x 467mm)
Left Side (D2048C)
(1978 x 471mm)
Right Side (D2049C)
(1978 x 471mm)
Back (X956)
(1914 x 988mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 12
C
G H
J K
Hinge (F518) x 8
F
13mm Screw (F63) x 20
I
E
13mm Screw (F79) x 1
D
Nail (F51) x 40
Large locking nut (F900) x 12
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
Rule
ScissorsSquare
Spirit level
Hammer Bradawl
Eye protection (when using a hammer or drill)
Cross-head screwdriver
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Step ladder
Ruler - Use this ruler to help correctly identify the screws
Electric drill (only use when drilling into walls)
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
Shelf stud (F110) x 4
Rail holder
(F1014) x 4
19mm Screw (F461) x 4
Hinge plate (F523) x 8
L
Bracket (F327) x 1
M
Handle (F266) x 2
N
Plastic Nail (F91) x 4
Finished
front edge
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
10mm
A
Prepare the left side
Screw 4 metal dowels into the left side .
Note: Tighten metal dowels up fully against the panel.
Fit 4 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.
Insert 2 large locking nuts into the left side . .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Tap a wooden dowel into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
B
1
J
1
C
A
1
1
B
C
J
B
B
B
C
C
B
J
J
J
J
1
B
These 2 holes are not used
Assembly Instructions
5
Step 2
Prepare the right side
Screw 4 metal dowels into the right side .
Insert 2 large locking nuts into the right side .
Fit 4 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
Tap a wooden dowel into the right side .
B
2
J
2
C
A
2
2
B
C
B
B
B
C
Finished
front edge
J
2
J
J
J
J
A
A
Prepare the base
Insert 4 large locking nuts into the base .
Tap 2 wooden dowels into the base .
C
C
C
C
C
Finished
front edge
plain chipboard surface
4
A
4
A
4
Step 3
These 2 holes are not used
B
Finished
front edge
A
Assembly Instructions
6
Step 4
Step 5
A
C
plain chipboard surface
7
Prepare the plinth
Insert 2 large locking nuts into the plinth .
Tap 2 wooden dowels into the plinth .
C
7
A
7
Finished
front edge
Fit the base to the right side
Push the base onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the base .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
4
plain chipboard surface
B
C
2
4
2
4
C
C
C
Note: The plinth is narrower than the back rail (please refer to the panels page).
Finished
front edge
A
Assembly Instructions
7
Step 6
Fit the plinth
Push the plinth onto the right side .
Use a screwdriver to tighten the large locking nut fitted to the plinth . .
7
2
7
C
Step 7
Prepare the back rail
Insert 2 large locking nuts into the back rail . .
Tap 2 wooden dowels into the back rail .
C
6
A
6
C
C
A
plain chipboard surface
6
plain chipboard surface
7
2
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 8
Fit the back rail to the left side
Push the back rail onto the left side .
Use a screwdriver to tighten the large locking nut fitted to the back rail .
6
1
6
C
plain chipboard surface
6
1
7
2
6
1
Step 9
Fit the left side
Push the left side onto the base and plinth , then push the back rail onto the right side .
Use a screwdriver to tighten the 4 large locking nuts fitted to the back rail , base , and plinth .
1
4
7
6
2
C
6 4
7
4
Assembly Instructions
9
Step 10
Prepare the top
Screw 4 metal dowels into the top .
Step 11
Fit the top and plastic nails
Push the top onto the assembly.
Use a screwdriver to tighten the 4 large locking nuts fitted to the left side and right side .
B
B
B
B
B
3
3
1
2
C
3
Rounded
front edge
2
1
Rounded
front edge
3
Tap 2 plastic nails into the bottom edge of each of the sides and . .
N
1
2
N
N
N
N
Assembly Instructions
10
Step 12
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
10
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
Step 13
Warning: The unit is heavy. Lift with care.
I
Fit the hanging rails
You can fit the 2 hanging rails using any of the 4 positions shown opposite.
Note: The rail at position 4 is used for shoe storage.
Insert 2 rail holders for each of the 2 rails and then secure with them with screws .
Push the hanging rails down into the rail holders . .
F
8
I
8
I
F
8
I
2
3
b:
D
y
x
y
y
x
10
8
8
8
8
Rail Position 2
Rail Position 3
Rail Position 4
Rail Position 1
Assembly Instructions
11
Step 14
90
K
Prepare the 2 doors
Push fit 4 hinges into each of the doors .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
F
K
K
F
F
K
F
F
K
F
F
K
F
F
Step 15
9
x 2
Fit the shelves
Insert 4 shelf studs at position 1or 2 for the shelf .
Lower the shelf down onto the shelf studs .
G
5
5
G
9
G
G
G
G
G
G
G
G
Shelf Position 1
Shelf Position 2
5
Assembly Instructions
12
Step 16
H
Fit doors and handles
Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a handle to
each door using 2 screws .
K
K
J
J
J
K
J
9
9
e:
a: b:
c: d:
J
K
J
J
B
J
K
K
K
A
K
J
B
M
H
K
M
M
H
H
9
9
Assembly Instructions
13
Step 17
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
14
Step 18
H
Top of Unit
WALL
WALL
Back of Unit
Attach bracket to top
To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket fitted to the top of the unit.
Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back of the unit to the wall.
Fix the bracket loosely onto the top of the unit using screw and mark the wall for the wall fixing.
Swivel the bracket away from the wall and drill a hole in the wall using a suitable drill bit and fit your wall fixing.
Swivel the bracket back and fix the bracket to the wall, then tighten Screw .
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Warning: The robe is heavy. Lift with care.
L
L
E
L
L
E
L
E
L
Assembly Instructions
15
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR3004
Step 19
Warning: The unit is heavy. Lift with care.
Assembly is complete
Loading...