Argos ZNO4D-MW-AR, ZNO4D-WO-AR, ZNO4D-DLO-AR ASSEMBLY INSTRUCTIONS
MADE IN
BRITAIN
Dimensions
4 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Important - Please read these instructions fully before starting assembly
227/6478
266/2185
244/2941
Width - 75cm
Depth - 40cm
Height - 74.5cm
Issue 4 - 09/09/14
349/8042
356/9304
343/2709
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 26kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
2
1
4
6
Drawer Front (D0218A)
(737 x 162mm) x 4
2
3
5
10
9
Drawer Base (T695-367)
(695 x 367mm) x 4
Drawer Back (W684-124)
(684 x 124mm) x 4
Rail (D2201A)
(717 x 60mm) x 2
Top (D2200A)
(750 x 396mm)
Left Side (D2198A)
(721 x 372mm)
Right Side (D2199A)
(721 x 372mm)
Back (X741-700)
(741 x 700mm)
7
8
Left Drawer Side
(W370-124LH)
(370 x 124mm) x 4
Right Drawer Side
(W370-124RH)
(370 x 124mm) x 4
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 6
B
Metal dowel (F901) x 14
C
D E F
G
K
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Large locking
nut (F900) x 6
Nail (F51) x 19
Small locking
nut (F3) x 8
9mm Screw (F73) x 16
9mm Screw (F74) x 8
H
Drawer runner (F1004) x 8
Cross-head
screwdriver
I
Handle (F847a ) x 4
a
I
Handle screw (F847b) x 8
b J
Knock-in Peg (F171GY) x 16
L
Wedgefix (F639) x 16
Plastic Nail (F91) x 4
Loading...