Argos ZNMSBS-FE-ARHD, ZNMSBS-FE-ARSI, ZNMSBS-HM-ARHD, ZNMSBS-HM-ARSI, ZNMSBS-NW-ARHD ASSEMBLY INSTRUCTIONS

...
Page 1
MADE IN
BRITAIN
Dimensions
Width - 39cm
Depth - 40cm
Height - 45cm
Malibu - Single Bedside
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 9 - 07/10/14
Important - Please read these instructions fully before starting assembly
257/3717
268/8303
257/2749
267/6793
259/5726
346/0142
345/8075
362/4713
343/9829
346/6005
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 10kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Page 3
Components - Panels
Please check you have all the panels listed below
2
1 2 3
8
10
11
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
9
13
4 5
6
7
Drawer Back (W317-124BCK)
(317 x 124mm)
Left Side (D2848A)
(431 x 394mm)
Left Drawer Side (W370-124LH)
(370 x 124mm)
Right Drawer Side (W370-124RH)
(370 x 124mm)
Drawer Base (T328-367)
(328 x 367mm)
Right Side (D2849A)
(431 x 394mm)
Drawer Front (D2824A)
(345 x 156mm)
Shelf (D2862A)
(349 x 392mm)
Back (X373-351)
(373 x 351mm)
Plinth (D2825A)
(349 x 92mm)
Rail (D2826A)
(349 x 72mm)
Back Rail (D2836A)
(349 x 60mm)
Top (D2823A)
(388 x 396mm)
12
Page 4
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Rule Scissors Hammer Eye protection
(when using a hammer or drill)
Cross-head screwdriver
Ruler - Use this ruler to help correctly identify the screws
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 4
D
Large locking nut (F900) x 2
E
Small locking nut (F3) x 2
F
G
40mm Screw (F910) x 8
H
25mm Screw (F50) x 1
I
Nail (F51) x 10
Handle (F631) x 1
K
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Knock-in Peg (F171WH) x 4
J
L
C
Drawer runner (F1004) x 2
Plastic Nail (F91) x 4
N
Wedgefix (F639) x 2
M
9mm Screw (F74) x 2
9mm Screw (F73) x 4
Page 5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
7
B
B
B
F
F
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
F
F
4
5
B
B
Step 2
Prepare the drawer front
Screw 2 metal dowels into the drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
7
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
F
4
5
Attach the drawer sides to the drawer front
Push the left drawer sides . and right drawer sides . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
4 5
7
F
F
4 5
7
4
5
Page 6
Assembly Instructions
5
Step 4
I
I
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
8
4 5
7
6
4 5
8
6
6
I
Attach the handle
Attach the handle to the drawer front using screw .
Note: Do not overtighten the screw.
K
H
7
4 5
Step 7
Fit the wedgefixes
Turn the drawer assembly over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
N
I
I
N
N
N
8
4
5
7
6
4
5
8
K
H
7
Page 7
A
Finished
front edge
6
Finished
front edge
L
J
Prepare the left side
a: Place a runner on
the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
Insert a large locking nut into the left side . .
Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.
Tap a wooden dowel into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
1
L
L
1
J
J
E
a:
b:
10mm
A
E
1
A
1
L
J
Finished
front edge
L
E
1
1
Assembly Instructions
Step 8
Page 8
A
Assembly Instructions
7
Step 9
Prepare the right side
a: Place a runner on
the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
Insert a large locking nut into the right side . .
Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.
Tap a wooden dowel into the right side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
2
L
L
2
J
J
E
2
A
2
Finished
front edge
L
J
Step 10
a:
b:
L
J
Finished
front edge
Finished
front edge
E
L
2
2
A
A
A
A
A
A
A
A
Prepare the plinth, rail and back rail
a: Tap 2 wooden
dowels into the plinth . .
b: Tap 4 wooden
dowels into the rail .
a: Tap 2 wooden
dowels into the back rail .
A
A
10
A
12
11
Finished
front edge
plain chipboard surface
plain chipboard surface
plain chipboard surface
10
12
11
a:
b:
c:
Page 9
G
G
Finished
front edge
Assembly Instructions
8
Step 11
Step 12
Fit the plinth and back rail to the right side
Push the plinth onto the right side and secure it with screw .
Push the back rail onto the right side and secure it with screw . .
Note: Support the back rail until the left side has been fitted in the next step.
G
10
2
G
12
2
Fit the shelf and the rail to the right side
Position the shelf against the right side as shown and secure with 2 screws .
Push the rail onto the right side .
Finished
front edge
G
G
plain chipboard surface
9
2
G
9
2
Finished
front edge
plain chipboard surface
11
11
2
plain chipboard surface
10
plain chipboard surface
12
2
Page 10
Assembly Instructions
9
Step 13
Fit the left side
Push the left side onto the unit and secure it with 4 screws .
G
1
G
G
G
G
1
B
Prepare the top
Screw 2 metal dowels into holes shown on the underside of the top .
3
Step 14
B
B
plain chipboard surface
Finished
front edge
3
Page 11
Assembly Instructions
10
Step 15
Step 16
1
2
3
Attach the top
Push the top onto the side panels and . .
Use a screwdriver to tighten the large locking nut fitted to each side.
Note: Turn the large locking nut as far as it will go - more than 1/2 a turn.
3
E
E
B
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
b:
y
y
x
x
13
D
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
13
D
13
1
2
Page 12
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
11
Step 17
ALR3029
Fit the 4 plastic nails
Tap 2 plastic nails into the bottom edge of each side and as shown.
Stand the unit up for the next step.
C
1 2
Fit the drawers
Slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws. If they catch on the runner you may need to loosen them slightly.
Assembly is complete
M
J
J
2nd threaded
hole
J
M
4 5
Step 18
C
C
C
C
1
2
M
M
4
5
Loading...