Argos ZNMDE-O-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 120cm

Depth - 49cm

Height - 72cm

Malibu - Desk

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 12 - 22/07/14

Important - Please read these instructions fully before starting assembly

275/6297

278/6009

274/6616

278/5220

247/3848

278/6652

268/6965

238/3615

275/3922

246/4950

246/5818

280/0332

247/7167

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 24kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

2

1

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

2

3

5

8

13

7

6

Drawer Back (W317-124)

(317 x 124mm) x 3

Drawer Base (T328-317)

(328 x 317mm) x 3

Back (X646-375)

(646 x 375mm)

Left Side (D2785A)

(706 x 353mm)

Right Side (D2786A)

(706 x 353mm)

Bookcase End (D2787A)

(706 x 186mm) x 2

Shelf (D2788A)

(394 x 182mm) x 3

Rail (D2790A)

(349 x 80mm)

12

11

Plinth (D2789A)

(349 x 92mm)

Drawer Front (D2791A)

(345 x 196mm) x 3

9

10

Top (D2784A)

(1200 x 490mm)

Left Drawer Side (W320-124LH)

(320 x 124mm) x 3

Right Drawer Side (W320-124RH)

(320 x 124mm) x 3

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 8

B

Metal dowel (F901) x 14

C

D

Large locking nut (F900) x 8

E

Small locking nut (F3) x 6

F

IG

40mm Screw (F910) x 16

H

NL M

25mm Screw (F50) x 3

J

Rule Scissors Hammer Eye protection

(when using a hammer or drill)

Cross-head screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Handle (F631) x 3

Nail (F51) x 11

Knock-in Peg (F171GY) x 12

Wedgefix (F639) x 6

Drawer runner (F1004) x 6

K

9mm Screw (F73) x 12

9mm Screw (F74) x 6

Plastic Nail (F91) x 8

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

8

x 3

B

F

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

F

9

10

Step 2

Prepare the 3 drawer fronts

Screw 2 metal dowels into each of the drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

B

8

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

F

9

10

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

9

10

8

F

9

10

9

10

B

8

N

Assembly Instructions

5

Step 4

N

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

12

9 10

8

11

9 10

12

11

N

Attach the handles

Attach a handle to each of the drawer fronts . using screw .

Note: Do not overtighten the screw.

D

H

8

9 10

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

M

x 3

N

x 3

M

12

9

10

11

9

10

12

D

H

8

Finished

front edge

Finished

front edge

A

Assembly Instructions

6

Step 8

E

Finished

front edge

K

J

Prepare the left side

a: Place 3 runners on

the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the left side .

Insert 2 large locking nuts into the left side . .

Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.

Tap a wooden dowel into the left side .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

1

K

1

J

E

a:

b:

10mm

A

E

1

A

1

K

J

K

J

K

J

K

1

Main unit

colour

Finished

top edge

A

Assembly Instructions

7

L

Step 9

Step 10

Prepare the plinth and the rail

Tap 2 wooden dowels into the plinth .

Tap 2 wooden dowels into the rail .

A

6

7

Prepare the right side

a: Place 3 runners on

the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the right side .

Insert 2 large locking nuts into the right side .

Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.

Tap a wooden dowel into the right side .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

2

K

2

J

E

2

A

2

Finished

front edge

K

J

Finished

front edge

a:

b:

K

J

K

J

K

J

K

E

Finished

front edge

2

A

Note: The rail may be plain chipboard or its colour may differ from the main unit colour.

Note: The plinth will be finished with the main unit colour on one surface.

Plain chipboard

surface

(349 x 80mm)

(349 x 92mm)

6

7

G

Main unit

colour

Assembly Instructions

8

Step 11

Step 12

Finished

top edge

6

7

Fit the plinth and the rail to the right side

Push the plinth onto the right side and secure it with screw .

Push the rail onto the right side and secure it with screw .

2

6

G

2

7

G

2

Fit the left side

Push the left side onto the unit and secure it with 2 screws .

Step 13

G

1

G

1

Fit 4 plastic nails

Tap 2 plastic nails into the bottom edge of each side and as shown.

I

1 2

I

Note: Support the rail until the left side has been fitted in the next step.

I

1

2

Prepare the 2 bookcase ends

Insert 2 large locking nuts into each bookcase end .

Tap a wooden dowel into each bookcase end . .

A

Assembly Instructions

9

L

Step 14

Step 15

3

E

A

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back

down onto the unit, making sure that it is flush with the bottom of the rail .

Nail down the sides and along the bottom edge of the back .

Note: Nails should be spaced about 150mm apart.

13

7

13

C

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

b:

y

x

13

7

inside

surface

E

x 2

3

x

C