Argos ZNM3D-FE-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 38cm

Depth - 40cm

Height - 61cm

Malibu - 3 Drawer Bedside Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 7 - 24/06/14

Important - Please read these instructions fully before starting assembly

267/7905

262/9049

257/8633

262/1449

268/4943

266/8275

274/8762

249/7264

278/4056

267/8076

275/5549

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 14kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

2

1 2

3

7

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Drawer Back (W317-124)

(317 x 124mm) x 3

Drawer Front (D2824A)

(345 x 156mm) x 3

Drawer Base (T328-367)

(328 x 367mm) x 3

Left Side (D2821A)

(591 x 394mm)

Plinth (D2825A)

(349 x 92mm)

Rail (D2826A)

(349 x 72mm)

Back Rail (D2836A)

(349 x 60mm)

Back (X511-373)

(511 x 373mm)

Left Drawer Side (W370-124LH)

(370 x 124mm) x 3

Right Drawer Side (W370-124RH)

(370 x 124mm) x 3

Right Side (D2822A)

(591 x 394mm)

10

5

Top (D2823A)

(388 x 396mm)

6

8 9

11 12

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 10

B

Metal dowel (F901) x 8

C

Nail holder (F149) x 1

D

Large locking nut (F900) x 2

E

Small locking nut (F3) x 6

F

G

40mm Screw (F910) x 4

H

25mm Screw (F50) x 3 Handle (F631) x 3

I

J

Rule Scissors Hammer Eye protection

(when using a hammer or drill)

Cross-head screwdriver

Nail (F51) x 12

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

K

O

Drawer runner (F1004) x 6

Plastic Nail (F91) x 4

N

Wedgefix (F639) x 6

M

9mm Screw (F74) x 6

Knock-in Peg (F171GY) x 12

L

9mm Screw (F73) x 12

7

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 3

B

F

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

F

8

9

B

Step 2

Prepare the 3 drawer fronts

Screw 2 metal dowels into each of the drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

B

7

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

F

8

9

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

8 9

7

F

8 9

7

8

9

L

Assembly Instructions

5

Step 4

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

11

8 9

7

10

8 9

11

10

L

Attach the handles

Attach a handle to each of the drawer fronts . using screw .

Note: Do not overtighten the screw.

I

H

7

8 9

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

N

x 3

L

x 3

N

11

8

9

7

10

8

9

11

I

H

7

Finished

front edge

A

Finished

front edge

Assembly Instructions

6

Step 8

Finished

front edge

K

J

K

J

Prepare the left side

a: Place 3 runners on

the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the left side .

Insert a large locking nut into the left side . .

Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.

Tap a wooden dowel into the left side .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

1

K

1

J

K

J

K

J

K

E

a:

b:

10mm

A

E

1

A

1

A

Assembly Instructions

7

Step 9

Prepare the right side

a: Place 3 runners on

the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the right side .

Insert a large locking nut into the right side . .

Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.

Tap a wooden dowel into the right side .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

2

K

2

J

E

2

A

2

Finished

front edge

K

J

Finished

front edge

Finished

front edge

K

J

K

J

K

J

E

2

A

Step 10

Prepare the plinth, rail and back rail

a: Tap 2 wooden

dowels into the plinth . .

b: Tap 4 wooden

dowels into the rail .

a: Tap 2 wooden

dowels into the back rail .

A

4

A

6

5

Finished

front edge

plain chipboard surface

4

6

5

a:

b:

c:

b: