Page 1
MADE IN
BRITAIN
Dimensions
Width - 145.5cm
Depth - 50cm
Height - 181cm
Malibu - 3 Drawer 2+2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 6 - 04/09/14
Important - Please read these instructions fully before starting assembly
258/6890
257/7517
268/2811
244/7142
268/4534
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 101kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1
6 7
5
2
Top (D2851A)
(1423 x 494mm)
Base (D2856A)
(1423 x 494mm)
Drawer Front (D2783A)
(710 x 156mm) x 3
Drawer Base
(T693-367)
(693 x 367mm) x 3
Left Drawer
Side (W370-124LH)
(370 x 124mm) x 3
Right Drawer
Side (W370-124RH)
(370 x 124mm) x 3
3
Drawer Back (W682-124BCK)
(682 x 124mm) x 3
4
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Page 3
Components - Panels
Please check you have all the panels listed below
2
8
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
9 10 11
18 19 2120
12
Long Hanging Rail (FHR704)
(704mm long)
13
Short Hanging Rail (FHR330)
(330mm long) x 2
14
16 1715
Left End (D2852A)
(1808 x 496mm)
Right End (D2853A)
(1808 x 496mm)
Left Divider (D2854A)
(1684 x 477mm)
Right Divider (D2855A)
(1684 x 477mm)
Horizontal (D2861A)
(716 x 476mm) x 2
Loose Shelf (D2858A)
(337 x 476mm) x 2
Plinth (D2859A)
(1423 x 92mm) x 2
Large Door (D2845A)
(1678 x 353mm) x 2
Short Door (D2857A)
(1198 x 353mm) x 2
Rail (D2860A)
(338.5 x 125mm)
x 2
Small Back (X1710-358)
(1710 x 358mm) x 2
Large Back (X1710-726)
(1710 x 726mm)
Page 4
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 20
B
Metal dowel (F901) x 6
C
D E
G H I
Small locking
nut (F3) x 6
40mm Screw (F910) x 32
J K
Nail (F51) x 44
25mm Screw (F50) x 10
F
13mm Screw (F79) x 1
13mm Screw (F63) x 26
Rail holder
(F1014) x 6
Bracket (F327 x 1)
M N
Hinge (F522) x 10
L
Q
Hinge plate (F523) x 10
Handle (F631) x 10
O
Shelf stud (F110) x 8
Nail screw (F277) x 12
V
R S T
U
Knock-in Peg (F171GY) x 12
Plastic Nail (F91) x 6
9mm Screw (F74) x 6
9mm Screw (F73) x 12
Wedgefix (F639) x 12
Drawer runner (F1004) x 6
Rule
Square
Scissors
Spirit level
Hammer
Bradawl
Electric drill
Step ladder
Cross-head screwdriver
Eye protection (when
using a hammer or drill)
P
Back holder (F276) x 12
* These can
also be round
Page 5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 3
x 3
x 3x 3
B
B
B
C
Step 2
Prepare the 3 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
1
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
2
3
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
2
3
1
C
C
2
C
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the small groove is on the inside, as shown.
C
C
2
3
B
B
1
2
3
3
1
Page 6
Assembly Instructions
5
Step 4
V
V
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
5
2 3
1
4
2 3
5
4
4
V
Attach the handles
Attach a handle to
each of the drawer fronts
. using screw .
Note: Do not
overtighten the screw.
O
E
1
x 3
x 3
x 3
V
V
2 3
x 3
Step 7
T
T
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
T
5
2
3
1
4
2
3
5
E
E
1
O
O
T
T
T
Page 7
Finished
front edge
Finished
front edge
Finished
front edge
A
Assembly Instructions
6
Step 8
S
N
S
N
S
N
Finished
front edge
S
N
Prepare the left
divider
a: Place 3 runners on
the left divider as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left divider .
c: Fit 2 hinge plates
onto the left divider
making sure that the slot
is facing towards the
finished front edge.
Push a rail holder into
the left divider . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Tap 2 wooden dowels
into the left divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Turn the left divider
over
d: Push a rail holder
into the left divider .
Make sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
10
S
S
10
10
N
N
L
J
G
10
S
S
S
J
G
A
L
L
L
Turn the left
divider over
J
G
Finished
front edge
A
10
J
G
10
a:
b:
c:
d:
10
10
10
10
10mm
A
Page 8
Finished
front edge
7
Turn the right
divider over
Finished
front edge
S
N
S
N
S
N
S
S
S
L
Finished
front edge
L
L
J
G
Finished
front edge
Assembly Instructions
Step 9
Prepare the right
divider
a: Place 3 runners on
the right divider as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right divider .
c: Fit 2 hinge plates
onto the right divider
making sure that the slot
is facing towards the
finished front edge.
Push a rail holder into
the right divider .
Make sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Tap 2 wooden dowels
into the right divider .
Turn the right divider
over
d: Push a rail holder
into the right divider .
Make sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
11
S
S
11
11
N
N
L
J
G
11
A
11
J
G
11
Finished
front edge
S
N
J
G
A
A
11
11
11
11
a:
b:
c:
d:
Page 9
D
D
D
D
A
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 10
Step 11
Fit the right divider
Push the right divider
onto the 2 horizontals
. and secure with 4
screws .
16
11
D
Step 12
D
D
D
D
Fit the horizontals to
the left divider
Push the 2 horizontals
onto the left divider
and secure with 4
screws .
16
10
D
A
Prepare the 2
horizontals
Tap 2 wooden dowels
into each horizontal .
A
16
16
16
10
16
16
11
16
x 2
Page 10
Finished
front edge
D
Finished
front edge
D
D
D
Finished
front edge
A
A
A
Assembly Instructions
9
Step 13
Prepare the top, base
and 2 rails
Tap 2 wooden dowels
into the top .
Tap 2 wooden dowels
into the base .
Tap 2 wooden dowels
into each rail .
A
A
A
6
7
15
Fit the top, base and
rails
Push the top ,base
and the 2 rails onto
the 2 dividers and
and secure with
10 screws .
Step 14
6 7
15
10 11
D
x 2
D
10
A
A
plain chipboard surface
Finished
front edge
Finished
front edge
Plain chipboard
surface
A
6
7
15
D
plain chipboard surface
D
D
D
D
6
7
15
15
Finished
front edge
10
11
Page 11
Finished
front edge
Assembly Instructions
10
Step 15
Prepare the left end
Push a rail holder into
the left end . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates onto
the left end , making
sure that the slot is
facing towards the
finished front edge.
J
8
L
8
Step 16
Prepare the right end
Push a rail holder into
the right end . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates onto
the right end , making
sure that the slot is
facing towards the
finished front edge.
J
9
L
9
G
G
L
L
L
J
G
L
L
L
J
G
9
8
Finished
front edge
Page 12
D
D
D
D
D
Assembly Instructions
11
Step 17
Fit the right end
Push the right end
onto the top , base
and rail and secure
with 5 screws .
Step 18
9
6
15
D
A
A
Prepare the 2 plinths
Tap 2 wooden dowels
into each of the 2
plinths .
A
plain chipboard surface
12
x 2
12
7
6
7
15
9
Page 13
D
D
Assembly Instructions
12
Step 19
Step 20
Fit the 2 plinths
2 people are needed
here
Push the plinths onto
the right end and
secure with 2 screws .
12
9
D
Fit the left end
Push the left end
onto the top , the
base , the plinths
and the rail and
secure with 7 screws .
8
6
7
15
12
D
9
12
12
plain chipboard surface
Note: Support this plinth
until the left side has been
fitted in the next step.
12
12
D
D
D
D
D
D
D
8
6
7
15
Page 14
Assembly Instructions
Step 21
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
Fit the back panels
a: Square up the unit by
making sure that
measurement x:x equals
y:y.
Place the large back
and the 2 small backs
down onto the unit as
shown.
Make sure that
the 3 backs are
pushed up tight
against each
other and that
they meet over
the back edges
of the dividers.
b: Nail around
the outside edges
of the 3 backs.
Note: Do not nail where
the backs meet. Nails
should be spaced about
150mm apart.
Step 22
Secure the backs
Tap the nail screws
through the back holders
. and down between
the backs and
into the back edge
of the divider.
Keep tapping the
nail screws in
until the back
holders dig
into the small
and large back.
20
21
H
Q
P
20 21
Q
P
y
x
x
y
yy
Note: Do not
nail where the
backs meet.
b:
H
20
21
21
20
21
21
QP
+
x 6
QP
+
x 6
13
Q
P
P
Note: These can
also be round
Page 15
Assembly Instructions
Step 23
14
Warning: The
robe is heavy.
Lift with care.
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each end and as
shown.
Tap 1 plastic nail into
each plinth as shown.
Stand the unit up for
the next step.
U
8 9
U
U
U
U
8
9
U
12
12
12
U
U
Page 16
Assembly Instructions
15
Step 24
Step 25
Fit the hanging rails
and drawers
a: Push the long hanging
rail and 2 short
hanging rails into the
rail holders .
b: Starting with the
bottom drawer, slide
both the runners
forward and locate the
drawer sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .
Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.
Note: Do not overtighten
the screws.
If they catch on the
runner you may need to
loosen them slightly.
13
14
J
13
14
J
Fit the shelf studs
For each of the 2
loose shelves , insert
4 shelf studs .
I
17
b:
a:
2nd threaded
hole
N
R
R
R
14
14
13
N
2 3
N
R
I
x 4
I
x 4
Page 17
Assembly Instructions
16
Step 26
Step 27
Prepare the 4 doors
Push fit 3 hinges into
each large door and
2 hinges into each
short door .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
G
M
M
18
19
M
G
G
90
M
M
G
G
M
G
G
M
G
G
M
G
G
Fit the loose shelves
Lower the 2 loose
shelves down onto
the shelf studs .
I
17
18
19
x 2
x 2
17
17
Page 18
Small piece of
waste wood
Assembly Instructions
17
Step 28
Small piece of
waste wood
Drill a handle hole in
each short door
Important: Please follow
these instructions
carefully.
Lay the 2 short doors
down onto a smooth
surface.
Check that the hinges
and holes are in the
same place as the
diagrams.
Note: We recommend
the use of a small piece
of waste wood, placed
behind the hole while
drilling, to reduce the
possibility of any
breakout.
Using the pilot hole in
the rear face of the door,
drill through the hole
indicated opposite, using
a 2.5mm diameter drill.
Turn the door over and
open out the 2.5mm hole
that you have just drilled
by drilling back through it
with a 5mm drill.
IMPORTANT
Carefully choose which hole you
need to drill in each short door
19
ONLY drill this hole
in 1 short door
This will be the
left short door
ONLY drill this hole
in 1 short door
This will be the
right short door
19
19
Page 19
Assembly Instructions
18
Step 29
Fit doors and handles
Note: The easiest way to
attach each door and
. is to fit the top hinge
first, then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door and
using screws .
M
M
M
L
L
L
M
L
O
E
18
19
18 19
a: b:
c: d:
L
M
L
L
B
L
M
M
M
A
M
L
B
e:
Note: When fitting the short doors,
make sure that the handle hole you
had to drill is nearest to the bottom
of the door.
O
E
18
18
19
19
O
O
O
Page 20
Assembly Instructions
19
Step 30
b:
c:
d:
a:
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C
Page 21
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
20
Step 31
Attach bracket to top
To prevent possible
overbalancing, we
recommend that this unit
is secured to a suitable
wall by use of the
bracket fitted to the
top of the unit.
Fixings are not supplied,
as they will need to suit
the wall type and the
length of screw will
depend on the distance
from the back of the unit
to the wall.
Fix the bracket
loosely onto the top of
the unit using screw
and mark the wall for the
wall fixing.
Swivel the bracket
away from the wall and
drill a hole in the wall
using a suitable drill bit
and fit your wall fixing.
Swivel the bracket
back and fix the bracket
to the wall, then tighten
screw .
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Assembly is complete
Warning: The
unit is heavy.
Lift with care.
K
K
F
K
K
F
Top of Unit
WALL
WALL
Back of Unit
K
F
F
K
Page 22
Page 23
Page 24
ALR3034
Page 25
MADE IN
BRITAIN
Dimensions
Width - 145.5cm
Depth - 50cm
Height - 181cm
Malibu - 3 Drawer 2+2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 7 - 19/01/15
Important - Please read these instructions fully before starting assembly
258/6890
257/7517
268/2811
244/7142
268/4534
Page 26
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 101kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1
6 7
5
2
Top (D2851A)
(1423 x 494mm)
Base (D2856A)
(1423 x 494mm)
Drawer Front (D2783A)
(710 x 156mm) x 3
Drawer Base
(T693-367)
(693 x 367mm) x 3
Left Drawer
Side (W370-124LH)
(370 x 124mm) x 3
Right Drawer
Side (W370-124RH)
(370 x 124mm) x 3
3
Drawer Back (W682-124BCK)
(682 x 124mm) x 3
4
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Page 27
Components - Panels
Please check you have all the panels listed below
2
8
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
9 10 11
18 19 2120
12
Long Hanging Rail (FHR704)
(704mm long)
13
Short Hanging Rail (FHR330)
(330mm long) x 2
14
16 1715
Left End (D2852A)
(1808 x 496mm)
Right End (D2853A)
(1808 x 496mm)
Left Divider (D2854A)
(1684 x 477mm)
Right Divider (D2855A)
(1684 x 477mm)
Horizontal (D2861A)
(716 x 476mm) x 2
Loose Shelf (D2858A)
(337 x 476mm) x 2
Plinth (D2859A)
(1423 x 92mm) x 2
Large Door (D2845A)
(1678 x 353mm) x 2
Short Door (D2857A)
(1198 x 353mm) x 2
Rail (D2860A)
(338.5 x 125mm)
x 2
Small Back (X1710-358)
(1710 x 358mm) x 2
Large Back (X1710-726)
(1710 x 726mm)
Page 28
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 20
B
Metal dowel (F901) x 6
C
D E
G H I
Small locking
nut (F3) x 6
40mm Screw (F910) x 32
J K
Nail (F51) x 44
25mm Screw (F50) x 10
F
13mm Screw (F63) x 26
Rail holder
(F1014) x 6
M N
Hinge (F522) x 10
L
Q
Hinge plate (F523) x 10
Handle (F631) x 10
O
Shelf stud (F110) x 8
Nail screw (F277) x 12
R S T
U
Knock-in Peg (F171GY) x 12
Plastic Nail (F91) x 6
9mm Screw (F74) x 6
9mm Screw (F73) x 12
Wedgefix (F639) x 12
Drawer runner (F1004) x 6
Rule
Square
Scissors
Spirit level
Hammer
Bradawl
Electric drill
Step ladder
Cross-head screwdriver
Eye protection (when
using a hammer or drill)
P
Back holder (F276) x 12
* These can
also be round
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Page 29
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 3
x 3
x 3x 3
B
B
B
C
Step 2
Prepare the 3 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
1
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
2
3
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
2
3
1
C
C
2
C
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the small groove is on the inside, as shown.
C
C
2
3
B
B
1
2
3
3
1
Page 30
Assembly Instructions
5
Step 4
K
K
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
5
2 3
1
4
2 3
5
4
4
K
Attach the handles
Attach a handle to
each of the drawer fronts
. using screw .
Note: Do not
overtighten the screw.
O
E
1
x 3
x 3
x 3
K
K
2 3
x 3
Step 7
T
T
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
T
5
2
3
1
4
2
3
5
E
E
1
O
O
T
T
T
Page 31
Finished
front edge
Finished
front edge
Finished
front edge
A
Assembly Instructions
6
Step 8
S
N
S
N
S
N
Finished
front edge
S
N
Prepare the left
divider
a: Place 3 runners on
the left divider as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left divider .
c: Fit 2 hinge plates
onto the left divider
making sure that the slot
is facing towards the
finished front edge.
Push a rail holder into
the left divider . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Tap 2 wooden dowels
into the left divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Turn the left divider
over
d: Push a rail holder
into the left divider .
Make sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
10
S
S
10
10
N
N
L
J
G
10
S
S
S
J
G
A
L
L
L
Turn the left
divider over
J
G
Finished
front edge
A
10
J
G
10
a:
b:
c:
d:
10
10
10
10
10mm
A
Page 32
Finished
front edge
7
Turn the right
divider over
Finished
front edge
S
N
S
N
S
N
S
S
S
L
Finished
front edge
L
L
J
G
Finished
front edge
Assembly Instructions
Step 9
Prepare the right
divider
a: Place 3 runners on
the right divider as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right divider .
c: Fit 2 hinge plates
onto the right divider
making sure that the slot
is facing towards the
finished front edge.
Push a rail holder into
the right divider .
Make sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Tap 2 wooden dowels
into the right divider .
Turn the right divider
over
d: Push a rail holder
into the right divider .
Make sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
11
S
S
11
11
N
N
L
J
G
11
A
11
J
G
11
Finished
front edge
S
N
J
G
A
A
11
11
11
11
a:
b:
c:
d:
Page 33
D
D
D
D
A
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 10
Step 11
Fit the right divider
Push the right divider
onto the 2 horizontals
. and secure with 4
screws .
16
11
D
Step 12
D
D
D
D
Fit the horizontals to
the left divider
Push the 2 horizontals
onto the left divider
and secure with 4
screws .
16
10
D
A
Prepare the 2
horizontals
Tap 2 wooden dowels
into each horizontal .
A
16
16
16
10
16
16
11
16
x 2
Page 34
Finished
front edge
D
Finished
front edge
D
D
D
Finished
front edge
A
A
A
Assembly Instructions
9
Step 13
Prepare the top, base
and 2 rails
Tap 2 wooden dowels
into the top .
Tap 2 wooden dowels
into the base .
Tap 2 wooden dowels
into each rail .
A
A
A
6
7
15
Fit the top, base and
rails
Push the top ,base
and the 2 rails onto
the 2 dividers and
and secure with
10 screws .
Step 14
6 7
15
10 11
D
x 2
D
10
A
A
plain chipboard surface
Finished
front edge
Finished
front edge
Plain chipboard
surface
A
6
7
15
D
plain chipboard surface
D
D
D
D
6
7
15
15
Finished
front edge
10
11
Page 35
Finished
front edge
Assembly Instructions
10
Step 15
Prepare the left end
Push a rail holder into
the left end . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates onto
the left end , making
sure that the slot is
facing towards the
finished front edge.
J
8
L
8
Step 16
Prepare the right end
Push a rail holder into
the right end . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates onto
the right end , making
sure that the slot is
facing towards the
finished front edge.
J
9
L
9
G
G
L
L
L
J
G
L
L
L
J
G
9
8
Finished
front edge
Page 36
D
D
D
D
D
Assembly Instructions
11
Step 17
Fit the right end
Push the right end
onto the top , base
and rail and secure
with 5 screws .
Step 18
9
6
15
D
A
A
Prepare the 2 plinths
Tap 2 wooden dowels
into each of the 2
plinths .
A
plain chipboard surface
12
x 2
12
7
6
7
15
9
Page 37
D
D
Assembly Instructions
12
Step 19
Step 20
Fit the 2 plinths
2 people are needed
here
Push the plinths onto
the right end and
secure with 2 screws .
12
9
D
Fit the left end
Push the left end
onto the top , the
base , the plinths
and the rail and
secure with 7 screws .
8
6
7
15
12
D
9
12
12
plain chipboard surface
Note: Support this plinth
until the left side has been
fitted in the next step.
12
12
D
D
D
D
D
D
D
8
6
7
15
Page 38
Assembly Instructions
Step 21
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
Fit the back panels
a: Square up the unit by
making sure that
measurement x:x equals
y:y.
Place the large back
and the 2 small backs
down onto the unit as
shown.
Make sure that
the 3 backs are
pushed up tight
against each
other and that
they meet over
the back edges
of the dividers.
b: Nail around
the outside edges
of the 3 backs.
Note: Do not nail where
the backs meet. Nails
should be spaced about
150mm apart.
Step 22
Secure the backs
Tap the nail screws
through the back holders
. and down between
the backs and
into the back edge
of the divider.
Keep tapping the
nail screws in
until the back
holders dig
into the small
and large back.
20
21
H
Q
P
20 21
Q
P
y
x
x
y
yy
Note: Do not
nail where the
backs meet.
b:
H
20
21
21
20
21
21
QP
+
x 6
QP
+
x 6
13
Q
P
P
Note: These can
also be round
Page 39
Assembly Instructions
Step 23
14
Warning: The
robe is heavy.
Lift with care.
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each end and as
shown.
Tap 1 plastic nail into
each plinth as
shown.
Stand the unit up for
the next step.
F
8 9
F
F
F
F
8
9
F
12
12
12
F
F
Page 40
Assembly Instructions
15
Step 24
Step 25
Fit the hanging rails
and drawers
a: Push the long hanging
rail and 2 short
hanging rails into the
rail holders .
b: Starting with the
bottom drawer, slide
both the runners
forward and locate the
drawer sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .
Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.
Note: Do not overtighten
the screws.
If they catch on the
runner you may need to
loosen them slightly.
13
14
J
13
14
J
Fit the shelf studs
For each of the 2
loose shelves , insert
4 shelf studs .
I
17
b:
a:
2nd threaded
hole
N
R
R
R
14
14
13
N
2 3
N
R
I
x 4
I
x 4
Page 41
Assembly Instructions
16
Step 26
Step 27
Prepare the 4 doors
Push fit 3 hinges into
each large door and
2 hinges into each
short door .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
G
M
M
18
19
M
G
G
90
M
M
G
G
M
G
G
M
G
G
M
G
G
Fit the loose shelves
Lower the 2 loose
shelves down onto
the shelf studs .
I
17
18
19
x 2
x 2
17
17
Page 42
Small piece of
waste wood
Assembly Instructions
17
Step 28
Small piece of
waste wood
Drill a handle hole in
each short door
Important: Please follow
these instructions
carefully.
Lay the 2 short doors
down onto a smooth
surface.
Check that the hinges
and holes are in the
same place as the
diagrams.
Note: We recommend
the use of a small piece
of waste wood, placed
behind the hole while
drilling, to reduce the
possibility of any
breakout.
Using the pilot hole in
the rear face of the door,
drill through the hole
indicated opposite, using
a 2.5mm diameter drill.
Turn the door over and
open out the 2.5mm hole
that you have just drilled
by drilling back through it
with a 5mm drill.
IMPORTANT
Carefully choose which hole you
need to drill in each short door
19
ONLY drill this hole
in 1 short door
This will be the
left short door
ONLY drill this hole
in 1 short door
This will be the
right short door
19
19
Page 43
Assembly Instructions
18
Step 29
Fit doors and handles
Note: The easiest way to
attach each door and
. is to fit the top hinge
first, then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door and
using screws .
M
M
M
L
L
L
M
L
O
E
18
19
18 19
a: b:
c: d:
L
M
L
L
B
L
M
M
M
A
M
L
B
e:
Note: When fitting the short doors,
make sure that the handle hole you
had to drill is nearest to the bottom
of the door.
O
E
18
18
19
19
O
O
O
Page 44
Assembly Instructions
19
Step 30
b:
c:
d:
a:
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C
Page 45
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
20
Step 31
Fit the overbalance
protector kit
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of the
overbalance protector kit
. to the unit, or an
alternative fixing method
of your choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Assembly is complete
U
U
WALL
Wall fixing
(not supplied)
Screw
(not supplied)
Washer
Strap
U
Strap
Washer
Screw
TOP OF UNIT
U
Page 46
Page 47
Page 48
ALR3034
Loading...