Argos ZNM32R-PB-AR ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 74.5cm
Depth - 50cm
Height - 181cm
Malibu - 3 Drawer 2 Door Robe
227/8232
258/7679
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 8 - 04/09/14
Important - Please read these instructions fully before starting assembly
238/3574
237/1287
258/2904
279/1496
258/8032
279/1960
257/2512
262/6217
255/7788
247/7662
249/6612
278/0830
278/5189
266/7355
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 49.5kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
10
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
2 5
4
3
11
Left Side (D2871A)
(1808 x 496mm)
Base (D2841A)
(716 x 476mm)
Top (D2870A)
(716 x 494mm)
Right Side (D2872A)
(1808 x 496mm)
12
Plinth (D2873A)
(716 x 92mm) x 2
9
6
Back Rail (D2847A)
(716 x 92mm)
Rail (D2874A)
(716 x 92mm)
Drawer Base (T693-367)
(693 x 367mm) x 3
Left Drawer Side (W370-124LH)
(370 x 124mm) x 3
Right Drawer Side (W370-124RH)
(370 x 124mm) x 3
Door (D2857A)
(1198 x 353mm) x 2
Drawer Back (W682-124BCK)
(682 x 124mm) x 3
14
Drawer Front (D2783A)
(710 x 156mm) x 3
Back (X1710-740)
(1710 x 740mm)
7 8
Hanging Rail (FHR704)
(704mm long)
13
15
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 14
B
Metal dowel (F901) x 6
D F
G
40mm Screw (F910) x 14
J
13mm Screw (F79) x 1
H
25mm Screw (F50) x 8 Handle (F631) x 8
I
L
Nail (F51) x 33
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
K
M ON
P Q
Bracket (F327) x 1
Small locking nut (F3) x 6
Rail holder
(F1014) x 2
E
13mm Screw (F63) x 10
19mm Connecting bolt (F461) x 2
Hinge plate (F523) x 4
Hinge (F522) x 4
25mm Connecting sleeve (F432) x 2
Ruler - Use this ruler to help correctly identify the screws
Tools required
R S
U
Drawer runner (F1004) x 6
Knock-in Peg (F171GY) x 12
C
Plastic Nail (F91) x 5
9mm Screw (F74) x 6
T
9mm Screw (F73) x 12
Wedgefix (F639) 12
Rule Square Scissors Spirit level
Hammer Bradawl Electric drill Step ladder
Cross-head screwdriver Eye protection (when using a hammer or drill)
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 3
x 3
x 3x 3
B
B
B
E
Step 2
Prepare the 3 drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
E
6
7
Attach the drawer sides to the drawer fronts
Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
6 7
5
E
E
6
E
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
E
E
6
7
5
B
B
5
6
7
7
5
Assembly Instructions
5
Step 4
R
R
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
9
6 7
5
8
6 7
9
8
8
R
Attach the handles
Attach a handle to each of the drawer fronts . using screw .
Note: Do not overtighten the screw.
I
H
5
x 3
x 3
x 3
R
R
6 7
x 3
Step 7
U
U
Fit the wedgefixes
Turn the drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
U
9
6
7
5
8
6
7
9
H
H
5
I
I
U
U
U
Finished
front edge
Assembly Instructions
Step 8
6
T
P
T
P
T
P
Finished
front edge
T
P
a:
Finished
front edge
b:
Finished
front edge
c:
T
T
T
F
K
O
O
O
Prepare the left side
a: Place 3 runners on
the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
c: Fit 2 hinge plates
onto the left side making sure that the slot is facing towards the finished front edge.
Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .
1
T
T
1
1
P
P
O
F
K
1
1
1
1
Assembly Instructions
Step 9
7
a:
b:
c:
Prepare the right side
a: Place 3 runners on
the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
c: Fit 2 hinge plates
onto the right side making sure that the slot is facing towards the finished front edge.
Push a rail holder into the right side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .
2
T
T
2
2
P
P
O
F
K
2
Finished
front edge
T
P
T
P
T
P
T
P
T
T
T
O
O
F
K
O
2
2
2
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
G
G
G
G
A
A
Assembly Instructions
Step 10
8
Prepare top and base
a: Tap 2 wooden
dowels into the ends of the top .
b: Tap 2 wooden
dowels into the ends of the base .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
A
A
3
4
a:
b:
Fit the top and base to the right side
Push the top onto the right side and secure with 2 screws .
Push the base onto the right side and secure with 2 screws .
3
4
2
2
G
G
Step 11
A
A
4
plain chipboard surface
3
10mm
A
Finished
front edge
Finished
front edge
plain chipboard surface
4
3
2
Assembly Instructions
Fit the rail
Push the rail onto the right side .
Finished
front edge
Finished
front edge
A
A
Assembly Instructions
9
Step 12
Step 13
Prepare the 2 plinths, the rail and the back rail
a: Tap 2 wooden
dowels into the ends of the 2 plinths .
b: Tap 4 wooden
dowels into the ends of the rail .
c: Tap 2 wooden
dowels into the ends of the back rail .
A
10
A
12
A
11
11
2
A
A
A
A
A
A
x 2
Plain chipboard
surface
Plain chipboard
surface
Finished
front edge
Plain chipboard
surface
10
12
11
11
2
Assembly Instructions
This outer face should be the same colour as
the main unit panels
10
Step 14
G
Fit the 2 plinths
2 people are needed here
a: Push the
plinth at the front of the unit onto the right side and secure with screw .
b: Push the plinth at
the back of the unit onto the right side and secure with screw .
Note: Support the plinth at the back of the unit until the left side has been fitted.
10
2
G
Fit the back rail
Push the back rail onto the right side and secure with screw .
Note: Support the back rail until the left side has been fitted.
G
12
2
Step 15
G
10
2
G
a:
b:
G
Finished
front edge
10
10
12
2
2
Assembly Instructions
11
Step 16
Step 17
Fit the left side and the 4 plastic nails
Push the left side onto the unit and secure with 7 screws .
Tap 2 plastic nails into the bottom edge of each end and and 1 into the plinth as shown.
G
1
G
G
G
G
G
G
G
Warning: The robe is heavy. Lift with care.
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
D
15
yy
yy
x
x
1
C
C
C
C
C
1 2
2
10
10
C
b:
D
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
15
D
15
Assembly Instructions
12
Step 18
Fit the hanging rails and drawers
a: Push the hanging rail
. into the rail holders .
b: Starting with the
bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws. If they catch on the runner you may need to loosen them slightly.
13
F
13
F
b:
a:
2nd threaded
hole
P
S
P
6 7
P
S
S
S
13
Step 19
Prepare the 2 doors
Push fit 2 hinges into each door .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
K
Q
14
Q
K
K
90
Q
Q
K
K
14
x 2
Assembly Instructions
Small piece of
waste wood
14
Small piece of
waste wood
14
13
Step 20
Drill a handle hole in each door
Important: Please follow these instructions carefully.
Lay the 2 doors down onto a smooth surface.
Check that the hinges and holes are in the same place as the diagrams.
Note: We recommend the use of a small piece of waste wood, placed behind the hole while drilling, to reduce the possibility of any breakout.
Using the pilot hole in the rear face of the door, drill through the hole indicated opposite, using a 2.5mm diameter drill.
Turn the door over and open out the 2.5mm hole that you have just drilled by drilling back through it with a 5mm drill.
IMPORTANT
Carefully choose which hole
you need to drill in each door
14
ONLY drill this
hole in 1 door
This will be
the left door
ONLY drill this hole in 1 door
This will be
the right door
x 1
x 1
Assembly Instructions
14
Step 21
Fit doors and handles
Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a handle to
each door using screws .
Q
Q
Q
O
O
O
Q
O
I
H
14
14
a: b:
c: d:
O
Q
O
O
B
O
Q
Q
Q
A
Q
O
B
e:
Note: When fitting the doors, make sure that the handle hole you had to drill is nearest to the bottom of each door.
I
H
I
14
14
Assembly Instructions
15
Step 22
b:
c:
d:
a:
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
A
A
B
C
Assembly Instructions
16
Step 23
Joining units together
Fittings have been supplied so you are able to join units together.
Make sure that your first unit is level.
Push the other unit up against the first unit and ensure both units are level.
Check that the ends are flush and in line, then clamp them together.
Using a 5mm drill bit, drill through the 2 holes (shown circled) in the side panel into the adjoining side panel of the other unit.
Push the connecting sleeves into the holes and then screw the connecting bolts in from the other side.
5mm
N
M
N
M
N
M
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
17
Step 24
Attach bracket to top
To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket fitted to the top of the unit.
Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back of the unit to the wall.
Fix the bracket loosely onto the top of the unit using screw and mark the wall for the wall fixing.
Swivel the bracket away from the wall and drill a hole in the wall using a suitable drill bit and fit your wall fixing.
Swivel the bracket back and fix the bracket to the wall, then tighten screw .
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Assembly is complete
Warning: The unit is heavy. Lift with care.
L
L
J
L
L
J
Top of Unit
WALL
WALL
Back of Unit
L
L
J
L
Loading...
+ 42 hidden pages