Argos ZNM02R-PBLU-AR, ZNM02R-PPK-AR, ZNM02R-WHBLK-AR, ZNM02R-WHBLU-AR, ZNM02R-WHPK-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Malibu - 2 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 1 - 21/05/15

Important - Please read these instructions fully before starting assembly

428/3445

414/7756

424/3973

424/7302

412/3402

Width - 75cm

Depth - 49.5cm

Height - 181cm

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 49kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Hanging Rail (FHR704)

(70.4cm long)

Left Side (DF3568)

(180.8 x 49.6cm)

Right Side (DF3569)

(180.8 x 49.6cm)

Top/Base (DF3570)

(71.6 x 49.4cm) x 2

Shelf (DF3579)

(71.6 x 47.6cm)

Back Rail (DF3576)

(71.6 x 9.2cm)

Plinth (DF3575)

(71.6 x 9.2cm)

Door (DF3573)

(167.7 x 35.3cm) x 2

Back (X1711-742)

(171.1 x 74.2cm)

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Rule

Tools required

Rule

ScissorsSquare

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Step ladder

Electric drill (only use when drilling into walls)

A B C

D E

G H

40mm Screw (F910) x 16

I J

25mm Screw (F50) x 2

13mm Screw (F63) x 14

Nail (F51) x 31

Hinge (F522) x 6

Hinge plate (

F523)

x 6

Handle (F631) x 2

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Wooden dowel (F22) x 10

Plastic Nail (F91) x 4

Rail holder

(F1014) x 2

Finished

front edge

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

Step 2

Prepare the left side

Fit 3 hinge plates onto the left side making sure that the slot is facing towards the finished front edge.

Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .

Prepare the right side

Push a rail holder into the right side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .

Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

Finished

front edge

+ 10 hidden pages