Argos ZNHLDTSM-DA-AR, ZNHLDTSM-ME-AR, ZNHLDTSM-NW-AR, ZNHLDTSM-W-AR, ZNHLDTSM-WO-AR ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
New Hallingford - Dresser, Stool & Mirror
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 16/12/14
Important - Please read these instructions fully before starting assembly
346/9727
357/1268
356/3537
357/0290
330/6086
Dresser
Dimensions
Width - 99.5cm
Depth - 40cm
Height - 78.5cm
Stool
Dimensions
Width - 51.5cm
Depth - 35.5cm
Height - 45cm
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 34kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the overbalance kit supplied.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
2
7
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (DF1861)
(762 x 372mm)
Right Side (DF1862)
(762 x 372mm)
Divider (DF1865)
(162 x 355mm)
Top (DF1863)
(995 x 396mm)
Modesty (DF1864)
(960 x 163.5mm) x 2
Left Mirror Support (DF1868)
(147 x 250mm)
Mirror Back (DF1869)
(496 x 327mm)
Drawer Base (T434-347)
(434 x 347mm) x 2
3
Right Drawer Front (DF1967)
(489 x 162mm)
Left Drawer Front (DF1866)
(489 x 162mm)
Right Mirror Support (DF1968)
(147 x 250mm)
Drawer Back (W423-124)
(423 x 124mm) x 2
Left Drawer Side (W350-124LH)
(350 x 124mm) x 2
Right Drawer Side (W350-124RH)
(350 x 124mm) x 2
6
4 5
8
9 10
11 12
1413
15
Stool Top (D2332A)
(513 x 353mm)
Stool Base (D2336A)
(478 x 308mm)
Stool Drawer Front (D2338A)
(472 x 126mm)
Stool Left Side (D2333A)
(395 x 350mm)
19
16
Stool Right Side (D2334A)
(395 x 350mm)
17
Stool Rail (D2335A)
(478 x 124mm) x 2
20
Stool Drawer Back (W445-95)
(445 x 95mm)
Stool Drawer Base (T456-297)
(456 x 297mm)
Stool Left Drawer Side
(W300-95LH)
(300 x 95mm)
Stool Right Drawer Side
(W300-95RH)
(300 x 95mm)
Stool Seat Pad (FHALPAD)
(458 x 300mm)
18
21 22 23
24
25
Stool
Dresser
(Mirror - SG25 460 x 300mm Safety Back SAR)
3
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
B C
D E F
G
P
H
Small locking nut (F3) x 6
L
13mm Screw (F63) x 12
I
A
Wooden dowel (F22) x 11 Metal dowel (F901) x 36
Large locking nut (F900) x 30
Knock-in Peg (F171GY) x 12
M
R Runner (F160) x 2
b
L Runner (F161) x 2
M
c
L Runner (F159) x 2
M
a
R Runner (F162) x 2
M
d
350mm long
K
9mm Screw (F73) x 16
J
9mm Screw (F74) x 2
N
O
Q
Handle (F278) x 2
25mm Screw (F50) x 4
Plastic Nail (F91) x 8
Wedgefix (F639) x 6
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Mini block (F25) x 4
19mm Screw (F461) x 4
280mm long
Drawer runner (F1004) x 2
9 10
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 2
x 2
x 2
B
B
B
C
C
C
C
11
12
Step 2
Prepare the 2 drawer fronts
Screw 2 metal dowels into the left drawer front . and the right drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
9
10
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
11
12
Attach the drawer sides to the drawer fronts
Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts and .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
11 12
9 10
C
C
11 12
B
B
11
12
B
B
Note: The small right drawer fronts have an identification mark hole.
9
10
9 10
Assembly Instructions
5
Step 4
E
E
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front and .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
14
11 12
9 10
13
11 12
14
13
13
E
Attach the handles
Attach a handle to each of the drawer fronts . and using screw .
H
9 10
11 12
Step 7
Fit the wedgefixes
Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
F
x 2
x 2
x 2
E
E
x 2
F
F
F
14
11
13
11
12
14
12
O
O
H
H
9 10
Assembly Instructions
6
Step 8
Fit runners to the drawers
Fit runner , marked with ‘R’, to the bottom edge of the right drawer side , as shown, making sure that it is pushed up against the back of the drawer fronts . and . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit runner , marked ‘L’, to the bottom edge of the left drawer side using the same method.
11
M d
12
9 10
I
M c
M d
R
R
I
I
I
I
L
M c
L
Runners must be
pushed up against
the drawer front
11
12
9
10
D
Prepare the 2 modesty panels
Insert 4 large locking nuts into each modesty .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 9
D
6
D
D
D
D
x 2
x 2
Finished
front edge
6
Finished
front edge
A
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 10
Prepare the left side
a: Fit a runner to
the left side .
The 1st screw uses the 1st hole in from the front of the runner.
The 2nd and 3rd screws . use the holes that line up with the other panel holes.
b: Fit a screw into
the 2nd hole in at the top of the runners .
Tap a wooden dowel into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 2 large locking nuts into the left side . .
c: Screw 4 metal
dowels into the left side .
D
1
M a
1
K
K
I
M a
B
1
M a
K K
1st screw
2nd screw
K
3rd screw
Finished
front edge
M a
I
Finished
front edge
a:
b:
c:
K
M a
K
K
I
B
B
B
B
D
D
1
1
1
10mm
A
A
1
Loading...
+ 16 hidden pages