Argos ZNHL52D-DA-AR ASSEMBLY INSTRUCTIONS

Assembly Instructions - Please keep for future reference

Issue 6 - 02/05/14

MADE IN

BRITAIN

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number)

Important - Please read these instructions fully before starting assembly

Dimensions

Width - 74cm

Depth - 40cm

Height - 107.5cm

New Hallingford - 5+2 Drawer Chest

245/8629

266/1708

258/7772

267/6401

244/8639

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 37kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

2

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

1

Top (D2311A)

(740 x 396mm)

2 4

3

Rail (D2315A)

(705 x 66mm) x 3

14

Left Side (D2320B)

(1051 x 372mm)

Right Side (D2321B)

(1051 x 372mm)

Back (X1030-731)

(1030 x 731mm)

Divider (D2314A)

(165 x 282mm)

Small Drawer Front (D2309A)

(362 x 162mm) x 2

5

10

8

9

Large Drawer Front (D2316A)

(727 x 162mm) x 5

Large Drawer Base (T668-367)

(668 x 367mm) x 5

Small Drawer Base (T304-367)

(304 x 367mm) x 2

Large Drawer Back (W657-124)

(657 x 124mm) x 5

Small Drawer Back (W291-124)

(291 x 124mm) x 2

11

13

12

6 7

Left Drawer Side (W370-124LH)

(370 x 124mm) x 7

Right Drawer Side (W370-124RH)

(370 x 124mm) x 7

3

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Tools required

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Ruler - Use this ruler to help correctly identify the screws

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill (do not use for fitting screws)

B C

D E F

G H

Small locking nut (F3) x 14

Nail (F51) x 24

13mm Screw (F52) x 42 13mm Screw (F63) x 42

I

A

Wooden dowel (F22) x 9

19mm Screw (F461) x 14

Metal dowel (F901) x 24

Large locking nut (F900) x 10

Knock-in Peg (F171GY) x 28

M

R Runner (F160) x 7

b

L Runner (F161) x 7

M

c

L Runner (F159) x 7

M

a

R Runner (F162) x 7

M

d

350mm long

J

Handle (F278) x 7

K

13mm Screw (F79) x 1

L

Bracket (F327) x 1

O

Plastic Nail (F91) x 4

N

Wedgefix (F639) x 24

4

Step 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

x 2

B

Step 2

B

Prepare the 2 small drawer fronts

Screw 2 metal dowels into the holes shown on the back of each of the small drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

B

8

Prepare the 2 sets of the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

C

6

7

Attach the drawer sides to the small drawer front

Push the left drawer side . and right drawer side . onto the back of the small drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

6 7

8

C

6 7

C

8

B

C

Groove

C

x 2 x 2

x 2

C

6

7

6

7

Assembly Instructions

5

Step 4

Fit the small drawer base

Slide the small drawer base down the grooves in the drawer sides and and down into the groove in the small drawer front .

Step 5

Fit the small drawer back

Fit the small drawer back . between the drawer sides and .

Make sure that the small drawer base fits into the groove in the small drawer back .

Hold the small drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

10

6 7

8

9

6 7

10

9

E

6 7

Attach the handles

Attach a handle to each of the small drawer fronts using 2 screws . .

J

G

8

Step 7

Fit the wedgefixes

Turn the small drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

N

E

J

8

G

x 2

N

8

x 2

7

6

10

7

10

6

9

E

Assembly Instructions

6

Step 8

Fit runners to the small drawers

Turn the 2 small drawer assemblies over.

Fit runner , marked with ‘R’, to the bottom edge of the right drawer side , as shown, making sure that it is pushed up against the back of the small drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit runner , marked ‘L’, to the bottom edge of the left drawer side using the same method.

6

M d

7

8

I

M c

x 5

B

Prepare the 5 large drawer fronts

Screw 2 metal dowels into the holes shown on the back of each large drawer front .

B

11

Step 9

Step 10

Prepare 5 sets of drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

C

6

7

I

Runners must be

pushed up against

the drawer front

M d

R

I

L

M c

L

8

6

7

x 2

C

x 5 x 5

C

6

7

Assembly Instructions

7

Step 11

Attach the drawer sides to the large drawer front

Push the left drawer side . and right drawer side . onto the back of the large drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

6 7

11

C

6 7

C

Fit the large drawer base

Slide the large drawer base down the grooves in the drawer sides and and down into the groove in the large drawer front .

13

6 7

11

Step 12

Step 13

Fit the large drawer back

Fit the drawer back between the drawer sides and .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

12

6 7

13

12

E

6 7

11

B

C

Groove

x 5

6

7

5

x 5

11

6

13

7

E

6

7

5

x 5

11

13

7

6

E

12

Assembly Instructions

8

Step 14

Attach the handles

Attach a handle to each of the large drawer fronts using 2 screws . .

Step 16

J

G

11

Fit runners to the large drawers

Turn the 5 large drawer assemblies over.

Fit runner , marked with ‘R’, to the bottom edge of the right drawer side , as shown, making sure that it is pushed up against the back of the large drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit runner , marked ‘L’, to the bottom edge of the left drawer side using the same method.

6

M d

7

11

I

M c

Step 15

x 5

N

11

N

J

G

I

Runners must be

pushed up against

the drawer front

M d

R

I

L

M c

L

11

6

7

x 5

Fit the wedgefixes

Note: Before adding the wedgefixes, make sure the assembled drawer is square.

Turn the drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

N

Finished

front edge

Finished

front edge

A

Assembly Instructions

9

Step 17

a:

Prepare the left side

a: Fit 6 runners to

the left side .

The 1st screw uses the 2nd hole in from the front of the runner.

The 2nd and 3rd screws . use the holes that line up with the other panel holes.

b: Fit a screw into

the 2nd hole in at the top of the runners .

Screw 3 metal dowels into the left side .

Insert a large locking nut into the left side . .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Tap a wooden dowel into the left side .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

b:

B

D

1

M a

1

H

M a

H

Finished front edge

H

1st screw

2nd screw

H

3rd screw

M a

Finished front edge

I

M a

A

1

10mm

A

D

H

M a

H

M a

H

M a

H

M a

H

M a

H

M a

H

1

I

D

B