Argos ZN05D-WO-AR, ZNO5D-MW-AR, ZNO5D-DLO-AR ASSEMBLY INSTRUCTIONS

Page 1
MADE IN
BRITAIN
Dimensions
Width - 75cm
Depth - 39.6cm
Height - 90.8cm
Normandy - 5 Drawer Chest
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 21/05/15
Important - Please read these instructions fully before starting assembly
428/2611
411/7717
414/2081
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 33kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.
• Dispose of all packaging carefully and responsibly.
Page 3
Components - Panels
Please check you have all the panels listed below
2
1
2 4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
5 6
Rail (D2370A)
(71.7 x 6cm) x 3
Drawer Front (D2366A)
(73.7 x 16.2cm) x 5
3
Top (D2363A)
(75 x 39.6cm)
Left Side (DF3875)
(88.6 x 37.2cm)
Right Side (DF3876)
(88.6 x 37.2cm)
Drawer Back (W684-124)
(68.4 x 12.4cm) x 5
Left Drawer Side (W370-124LH)
(37 x 12.4cm) x 5
Right Drawer Side (W370-124RH)
(37 x 12.4cm) x 5
Drawer Base (T695-367)
(69.5 x 36.7cm) x 5
Back (X869-743)
(86.9 x 74.3cm)
7
8
9 10
Page 4
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 18
C
D E F
G
K
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Large locking nut (F900) x 8
Nail (F51) x 25
Small locking nut (F3) x 10
9mm Screw (F73) x 20
9mm Screw (F74) x 10
H
Drawer runner (F1004) x 10
Cross-head screwdriver
J
Knock-in Peg (F171GY) x 20
L
Wedgefix (F639) x 20
Plastic Nail (F91) x 4
M
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
JI
Handle (FBARHANDLE ) x 5
a
I b
19mm Screw (F461) x 10
b
a
Electric drill (only use when drilling into walls)
Page 5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
B
B
5
Step 2
Prepare the 5 drawer fronts
Screw 2 metal dowels into the holes shown on the back of each drawer front .
B
5
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
D
6
7
Attach the drawer sides to the drawer fronts
Push the left drawer side . and right drawer side . onto the back of the drawer fronts .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
6 7
5
D
6 7
x 5
x 5
5
D
B
B
D
D
D
D
6
7
x 5
x 5
6
7
Page 6
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and then down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and .
Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
9
6 7
5
8
6 7
6 7
9
8
8
J
Attach the handles
Attach a handle to each drawer front using 2 screws .
5
5
6
I a
I b
x 5
x 5
11
J
J
Step 7
Fit the wedgefixes
Turn the drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
L
J
J
L
L
L
8
6
7
9
7
9
6
I
7
I b
I b
I a
6
x 5
5
L
L
x 5
Page 7
A
Finished
front edge
Assembly Instructions
Step 8
a:
b:
Finished
front edge
F
H
Prepare the left side
a: Place 5 runners on
left side . Slide back top of runner and use 2nd hole from the front to fit 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
c: Insert 1 large locking
nut into the left side . .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Tap a wooden dowel into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Screw 3 metal dowels into the left side .
1
H
H
F
F
c:
C
1
A
B
1
1
F
H
F
H
F
H
F
H
F
H
1
Finished
front edge
1
Finished
front edge
1
F
F
F
F
F
C
10mm
A
C
B
B
B
6
1
Page 8
A
Assembly Instructions
7
Step 9
Prepare the right side
a: Place 5 runners on
right side . Slide back top of runner and use 2nd hole from the front to fit 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
c: Insert 1 large locking
nut into the right side .
Tap a wooden dowel into the right side .
Screw 3 metal dowels into the right side .
2
H
F
b:
c:
a:
Finished
front edge
F
H
F
C
2
2
2
A
B
F
H
F
H
F
H
F
H
F
H
Finished
front edge
2
Finished
front edge
2
Finished
front edge
2
H
2
F
F
F
F
F
C
B
B
B
Page 9
Assembly Instructions
Step 10
8
A
A
C
C
Prepare the 3 rails
Insert 2 large locking nuts into each of the rails .
Tap 2 wooden dowels into each of the rails .
4
C
A
4
plain chipboard surface
4
Step 11
Fit the 3 rails
Push the 3 rails onto right side as shown.
Use a screwdriver to tighten the large locking nut fitted to each of the 3 rails .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
C
C
4
2
x 3
plain chipboard surface
plain chipboard surface
plain chipboard surface
Support these rails
until the left side
has been fitted in
the next step.
2
B
C
4
4
4
4
Page 10
Assembly Instructions
9
Step 12
4
4
4
1
4
C
4
Fit the left side
Fit the left side to the 3 rails .
Use a screwdriver to tighten the large locking nut fitted to each of the rails .
Carefully stand the unit up.
Warning: The unit is heavy. Lift with care.
1
Step 13
Prepare the top
Screw 2 metal dowels into the top .
Note: Tighten metal dowels up fully against the panel.
B
3
B
B
Rounded
front edge
3
Page 11
yy
yy
xx
Assembly Instructions
Step 14
10
Step 15
Fit the top
Lower the top onto the side panels and . .
Use a screwdriver to tighten the 2 large locking nuts fitted to the inside of the left side . and right side .
Carefully lay the unit down onto its front again.
3
1
2
C
1 2
b:
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
10
E
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
xx
Warning: The unit is heavy. Lift with care.
E
10
Rounded
front edge
3
1
2
Page 12
Assembly Instructions
11
Step 16
Step 17
Fit the 4 plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . .
Carefully stand the unit up for the next step.
K
1
2
K
K
K
K
1
2
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner .
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
G
H
2nd threaded
hole
G
6 7
H
H
G
7
H
G
G
6
7
Warning: The unit is heavy. Lift with care.
Page 13
Assembly Instructions
12
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 18
Fit the overbalance protector kit
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit . to the unit, or an alternative fixing method of your choice.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Assembly is complete
M
Attach the
strap to the unit
Attach the
strap to the wall
Wall fixing
(not supplied)
Washer
Strap
Strap
M
M
Example
Screw
(not supplied)
Washer
Screw
UNIT
Page 14
Page 15
Page 16
ALR3173
Loading...