Argos ZMA22R-DLO-AR, ZMA22R-LO-AR, ZMA22R-WH-AR ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Marlow - 2 Drawer 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 05/06/15
427/7712
424/5256
426/6455
Width - 91.1cm
Depth - 49.5cm
Height - 191.8cm
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 61kgs. Please lift with care.
• Check you have all the components and tools listed on pages 1, 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.
• Dispose of all packaging carefully and responsibly.
Rule
Tools required
Rule
ScissorsSquare
Spirit level
Hammer Bradawl
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Step ladder
Electric drill (only use when drilling into walls)
Components - Panels
Please check you have all the panels listed below
2
1
2
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Left Side (DF3934)
(180.3 x 41.3cm)
Right Side (DF3935)
(180.3 x 41.3cm)
Horizontal (DF3930)
(79.7 x 45.9cm)
3
Top (DF3625)
(91.1 x 49.5cm)
6
Large Rail (DF3742)
(79.7 x 11.9cm) x 2
5
Base Rail (DF3628)
(79.7 x 7.8cm)
Leg (DF3631)
(190.3 x 5cm) x 4
Left Door (DF3936)
(141 x 39.4cm)
Right Door (DF3937)
(141 x 39.4cm)
Drawer Back
(W765-124)
(76.5 x 12.4cm) x 2
Drawer Base (T776-367)
(77.6 x 36.7cm) x 2
Left Drawer Side (W370-124LH)
(37 x 12.4cm) x 2
Drawer Front (DF3630)
(79.1 x 19.2cm) x 2
Right Drawer Side (W370-124RH)
(37 x 12.4cm) x 2
Back (X1798-823)
(179.8 x 82.3cm)
8
Hanging Rail (FHR791)
(79.1cm long)
7
9
10 11 12
13
14 15
16
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
O
QP
40mm Screw (F910) x 4
Rail Holder (F891) x 2
13mm Screw (F63) x 16
Hinge plate (F523) x 6
Hinge (F522) x 6
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A B
D E F
G H I
L
Small locking nut (F3) x 4
C
R
Nail (F51) x 36
M
J
9mm Screw (F74) x 4
K
9mm Screw (F73) x 8
Drawer runner (F1004) x 4
38mm Screw (F81) x 36
Knock-in Peg (F171GY) x 8
Large locking nut (F900) x 10
Metal dowel (F901) x 14
Wooden dowel (F22) x 14
Handle (F449) x 6
19mm Screw (F461) x 12
N
Wedgefix (F639) x 8
S
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
9
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 2
x 2
x 2
x 2
A
A
C
C
C
C
10
11
11
10
A
A
Step 2
Prepare the 2 drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
A
9
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
10
11
Attach the drawer sides to the drawer fronts
Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
10 11
9
C
C
10 11
9
9
Assembly Instructions
5
Step 4
E
E
x 2
x 2
x 2
x 2
E
E
11
10
13
N
M
M
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
13
10 11
9
12
10 11
13
12
12
E
Attach the handles
Attach 2 handles to each of the drawer fronts . using screws .
L
H
9
10 11
Step 7
Fit the wedgefixes
Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
N
12
10
11
13
H
L
L
H
H
H
N
N
N
N
9
Assembly Instructions
6
Step 8
Fit 2 legs to the left side
Screw 2 legs to the left side using 18 screws .
Note: The top of the legs must be flush with the top of the left side.
G
8
1
Step 9
Fit 2 legs to the right side
Screw 2 legs to the right side using 18 screws .
Note: The top of the legs must be flush with the top of the right side.
G
8
2
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
1
8
8
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
2
8
8
D
D
Assembly Instructions
7
Step 10
1
10mm
D
K
O
K
O
P
Finished
front edge
I
M
Prepare the left side
a: Place 2 runners on
the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
c: Screw 5 metal
dowels into the left side .
Tap 2 wooden dowels into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the left side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.
Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.
1
I
I
1
M
M
A
1
a:
b:
c:
I
M
I
M
1
1
I
I
P
P
P
A
A
A
A
A
K
K
O
D
1
O
K
K
1
P
1
D
D
Assembly Instructions
8
Step 11
2
2
2
Finished
front edge
I
M
a:
b:
c:
Prepare the right side
a: Place 2 runners on
the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
c: Screw 5 metal
dowels into the right side .
Tap 2 wooden dowels into the right side .
To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the right side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.
Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
2
I
I
2
M
M
A
2
D
2
O
K
K
2
P
2
I
M
I
M
I
I
P
P
P
P
A
A
A
A
A
K
K
O
D
Assembly Instructions
9
Step 12
D
Prepare the horizontal
Insert 4 large locking nuts into the horizontal .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Tap 4 wooden dowels into the horizontal .
B
B
B
B
B
D
D
D
B
4
D
4
4
Finished
front edge
A
B
Fit the horizontal to the right side
Push the horizontal onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
2
4
B
B
4
Step 13
Step 14
Prepare the base rail
Insert 2 large locking nuts into the base rail . .
Tap 2 wooden dowels into the base rail .
B
5
5
D
Finished
front edge
4
D
B
B
5
Finished
front edge
2
Finished
front edge
Assembly Instructions
10
Step 15
Fit the base rail
Push the base rail onto the right side .
Use a screwdriver to tighten the large locking nut fitted to the base rail .
2
5
B
5
5
2
Step 16
B
B
D
D
Finished
front edge
Prepare the large rails
Insert 2 large locking nuts into each of the 2 large rails .
Tap 2 wooden dowels into each of the 2 large rails .
Step 17
B
6
6
D
6
Finished
front edge
Finished
front edge
Fit the 2 large rails
Push the 2 large rails onto the right side .
Use a screwdriver to tighten the large locking nut fitted each of the 2 large rails .
Note: Support both large rails until the left side has been fitted in the next step.
2
6
B
6
6
6
2
x 2
Finished
front edge
F
F
F
F
3
Assembly Instructions
11
Step 18
Step 19
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 5 large locking nuts fitted to the horizontal , the base rail and the 2 large rails .
B
4
1
5
6
4
1
5
6
6
Fit the top
Attach the top to the sides and using the 4 screws .
F
3
1 2
1
2
Assembly Instructions
12
Step 20
yy
yy
xx
b:
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Carefully stand the unit up for the next step.
16
R
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
16
xx
R
Warning: The unit is heavy. Lift with care.
16
7
O
Fit the hanging rail
Push the hanging rail into the rail holders fitted to the side panels.
7
O
7
Step 21
Assembly Instructions
13
Step 22
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
J
M
M
J
2nd threaded
hole
M
J
10 11
J
J
10
11
Step 23
Prepare the 2 doors
Push fit 3 hinges into the left door and the right door .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the
K
Q
14
15
90
Q
Q
K
K
Q
K
K
Q
K
K
Q
K
K
Q
K
K
Q
K
K
14
15
L
H
H
L
14
15
Assembly Instructions
14
Step 24
Fit doors and handles
Note: The easiest way to attach the left door and right door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a handle to
each door and using screws .
Q
Q
Q
P
P
P
Q
P
L
H
14
15
14 15
a: b:
c: d:
P
Q
P
P
B
P
Q
Q
Q
A
Q
P
B
e:
Assembly Instructions
15
Step 25
b:
c:
d:
a:
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
A
A
B
C
Assembly Instructions
16
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 26
Fit the overbalance protector
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit . to the unit, or an alternative fixing method of your choice.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Assembly is complete
S
S
WALL
Wall fixing
(not supplied)
Screw
(not supplied)
Washer
Strap
S
Strap
Washer
Screw
TOP OF UNIT
S
ALR3185
Loading...