MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 39.5cm
Height - 73.5cm
Lawson - Desk
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 2 - 17/04/15
Important - Please read these instructions fully before starting assembly
402/4439
412/3392
412/6416
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 20kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Left End (DF2766)
(716 x 392mm)
Modesty (DF2772)
(620 x 157mm)
Door (DF2771)
(326 x 321mm)
Back (X707-353)
(707 x 353mm)
Shelf (DF2770)
(327 x 373mm)
Upright (DF2767)
(716 x 392mm)
Right End (DF2768)
(716 x 392mm)
2 3
4 5 6
7
8
9
Base (DF2769)
(327 x 390mm) x 2
Top (DF2765)
(996 x 396mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
Nail (F51) x 14
J
Large locking
nut (F900) x 18
Metal dowel (F901) x 18
Rule
Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Square
Bradawl
Spirit
level
Shelf stud (F110) x 5
C
Hinge plate
(F523) x 2
Hinge (F522) x 2
13mm Screw (F63) x 425mm Screw (F50) x 2
Handle (F236) x 1
Plastic Nail (F91) x 6
Finished
front edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Step 2
A
A
A
A
A
B
Prepare the upright
Screw 4 metal dowels
into the upright .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the upright
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Turn the divider over
Screw 2 metal dowels
into the upright .
B
A
2
B
2
B
A
A
Finished
front edge
Turn the divider over
A
2
2
2
B
B
B
B
Finished
front edge
Prepare the 2 base
panels
Insert 4 large locking
nuts into each of the
2 base panels .
B
5
5
B
B
B
B
Finished
front edge
5
Finished
front edge
Finished
front edge
Assembly Instructions
5
Step 3
Step 4
A
B
Fit a base to the
upright
Push a base onto the
upright .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the upright .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
5
B
2
2
5
Fit the other base to
the upright
Push the base onto
the upright .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the upright .
Step 5
Prepare the left end
Screw 4 metal dowels
into the left end .
Insert 2 large locking
nuts into the left end
. .
Fit 2 hinge plates onto
the left end , making
sure that the slot is
facing towards the
finished front edge.
2
5
B
B
2
Finished
front edge
Finished
front edge
2
5
H
A
A
B
B
KH
H
A
A
A
1
B
1
H
1
1
Finished
top edge
Finished
front edge
Assembly Instructions
6
Step 6
5
5
1
Fit the left end
Push the left end
onto the 2 base panels
. .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each of the 2 base
panels .
5
5
1
B
B
B
B
B
Prepare the modesty
Insert 4 large locking
nuts into the modesty
. .
B
7
Step 7
Step 8
7
A
A
Finished
front edge
B
Prepare the right end
Screw 2 metal dowels
into the right end .
Insert 2 large locking
nuts into the right end
. .
B
A
3
B
3
3
Finished
front edge
Finished
top edge
Assembly Instructions
7
Step 9
Fit the modesty
Push the modesty
onto the upright .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the modesty .
Note: Support the
modesty until the right
end has been fitted in
the next step.
Step 10
2
7
7
B
Fit the right end
Push the right end
onto the modesty .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the modesty .
7
7
3
B
2
3
7
7
Step 11
A
Prepare the top
Screw 6 metal dowels
into the top .
A
4
A
A
A
A
A
Finished
front edge
4
yy
yy
Assembly Instructions
8
Step 12
Fit the ltop
Push the top onto
the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
left end , upright
and right end .
Step 13
3
1 2
3
B
4
1
2
4
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
9
F
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
9
xx
xx
F
9
Assembly Instructions
9
Step 14
Step 15
Fit the 6 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the left end ,
upright and right end
. .
Carefully stand the
unit up for the next
step.
G
1
2
3
G
G
G
C
x 4
G
G
G
Warning: The
unit is heavy.
Lift with care.
1
2
3
Fit 4 shelf studs
Insert 4 shelf studs
into the holes shown.
Step 16
Fit the shelf
Lower the shelf down
onto the shelf studs .
C
C
6
6
Finished
front edge
Assembly Instructions
10
Step 17
C
Fit the door stop
Push the remaining shelf
stud up into the hole
in the corner of the upper
base to act as a door
stop.
C
5
5
Step 18
Prepare the door
Push fit 2 hinges into
the door .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
E
I
8
I
E
E
90
I
I
E
E
8
J
D
D
8
Assembly Instructions
11
Step 19
Fit door and handle
Note: The easiest way to
attach the door is to
fit the top hinge first,
then align and fit the
other hinge.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
the door using 2
screws .
I
I
I
H
H
H
I
H
J
D
8
8
e:
a: b:
c: d:
H
I
H
H
B
H
I
I
I
A
I
H
B
Assembly Instructions
12
Step 20
b:
c:
d:
a:
Adjust the door if
needed
a: Before adjusting the
door, use a spirit level to
check the top (or base)
of the unit is level, frontto-back and side-to-side
in the 3 positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C
Assembly Instructions
13
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 21
Assembly is complete
ALR3189
Loading...