Argos HALLINGFORD, HALLINGFORD PACKAGE, ZHG44D-MWWG-AR, ZHG44D-SGGG-AR ASSEMBLY INSTRUCTIONS

Assembly Instructions - Please keep for future reference

MADE IN

BRITAIN

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number)

Important - Please read these instructions fully before starting assembly

Dimensions

Width - 119.5cm

New Hallingford - 4+4 Drawer Chest

Issue 7 - 05/02/15

Depth - 40cm

Height - 74.5cm

266/5508

268/9577

262/1638

245/7510

258/6625

272 825

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 41.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

Left Side (D2312A)

(721 x 372mm)

Top (D2322A)

(1193 x 396mm)

Right Side (D2313A)

(721 x 372mm)

Upright (D2323A)

(655 x 282mm)

Rail (D2325A)

(1158 x 66mm) x 2

Drawer Back (W518-124)

(518 x 124mm) x 8

Drawer Front (D2324A)

(588 x 162mm) x 8

Drawer Base (T529-367)

(529 x 367mm) x 8

Back (X1184-700)

(1184 x 700mm)

Left Drawer Side (W370-124LH)

(370 x 124mm) x 8

Right Drawer Side (W370-124RH)

(370 x 124mm) x 8

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Tools required

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Ruler - Use this ruler to help correctly identify the screws

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill (do not use for fitting screws)

B C

D E F

Small locking nut (F3) x 16

Nail (F51) x 26

13mm Screw (F63) x 48

Wooden dowel (F22) x 7

19mm Screw (F461) x 16

Metal dowel (F901) x 24

Large locking nut (F900) x 8

Knock-in Peg (F171GY) x 32

R Runner (F160) x 8

L Runner (F161) x 8

L Runner (F159) x 8

R Runner (F162) x 8

350mm long

Plastic Nail (F91) x 5

Wedgefix (F639) x 32

45mm Screw (F65) x 1

Bracket (F945) x 1

13mm Screw (F79) x 1

13mm Screw (F52) x 48

Handle (F278) x 8

Step 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

x 8

Step 2

Prepare the drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten the metal dowels up fully against the panels.

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

8 9

Groove

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the groove is on the inside, as shown.

x 8

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

x 8 x 8

+ 11 hidden pages