Argos Zest - Bedside ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 40cm
Depth - 40cm
Height - 43.5cm
Zest - Bedside
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 02/10/14
Important - Please read these instructions fully before starting assembly
280/6769
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 11kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
2 3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D2946A)
(396 x 396mm)
Horizontal (D2950A)
(362 x 394mm)
Back (X402-390)
(402 x 390mm)
Drawer Front (D2951A)
(374 x 192mm)
Left Side (D2947A)
(376 x 395mm)
Base (D2949A)
(396 x 396mm)
Right Side (D2948A)
(376 x 395mm)
Left Drawer Side (W370-124LH)
(370 x 124mm)
Right Drawer Side (W370-124RH)
(370 x 124mm)
4
5 6
7 8 9
10 11
Drawer Base (T321-367)
(321 x 367mm)
Drawer Back (W329-124)
(310 x 124mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A B C
D E F
G H I
Nail (F51) x 11
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
L
Knock-in Peg (F171GY) x 4
N
L
Wedgefix (F639) x 2
13mm Screw (F63) x 613mm Screw (F52) x 6
M
R Runner (F160) x 1
b
L Runner (F161) x 1
M
c
L Runner (F159) x 1
M
a
R Runner (F162) x 1
M
d
350mm long
40mm Screw (F910) x 4
Metal dowel (F901) x 10
Large locking nut (F900) x 8
Small locking nut (F3) x 2
K
Handle (F894GRN) x 1
Foot (F233) x 4
32mm Screw (F72) x 1
38mm Screw (F81) x 8
6
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
A
B
A
C
C
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
C
C
7
8
A
A
Step 2
Prepare the drawer front
Screw 2 metal dowels into the drawer front .
Note: Tighten the metal dowels up fully against the panels.
A
6
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
7
8
Attach the drawer sides to the drawer fronts
Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
7 8
6
C
C
7 8
6
7
8
6
Assembly Instructions
5
Step 4
J
J
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
10
7 8
6
9
7 8
10
9
9
J
Attach the handle
Attach the handle to the drawer front using screw .
Note: Do not overtighten the screw.
K
I
6
7 8
Step 7
Fit the wedgefixes
Turn the drawer assemby over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
L
J
J
L
L
L
10
7
8
9
7
8
10
I
K
6
Assembly Instructions
6
Step 8
Fit runners to the drawer
Fit the runner to the bottom edge of the left drawer side , as shown, making sure that it is pushed up against the back of the drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit the runner to the bottom edge of the right drawer side using the same method.
8
M c
7
6
H
M d
Runners must be
pushed up against
the drawer front
M c
H
H
H
H
M d
8
7
6
Step 9
Prepare the horizontal
Insert 4 large locking nuts into the horizontal .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Green
edge
B
B
B
B
B
B
5
5
Green edge
Assembly Instructions
7
Step 10
Step 11
A
Prepare the left side
Screw 2 metal dowels into the left side .
Insert 2 large locking nuts into the left side . .
Fit the runner to the left side .
The 1st screw uses the 2nd hole in from the front of the runner.
The 2nd and 3rd screws . use the holes that line up with the other panel holes.
Fit a screw into the 2nd hole in at the top of the runner .
A
B
B
M a
G
Finished front edge
G
1st screw
2nd screw
G
3rd screw
M a
Finished front edge
H
G
M a
G
G
H
A
1
B
1
M a
1
G
G
H
M a
1
B
B
A
A
M b
G
Finished front edge
G
1st screw
2nd screw
G
3rd screw
M b
Finished front edge
H
G
G
M b
G
H
Prepare the right side
Screw 2 metal dowels into the right side .
Insert 2 large locking nuts into the right side . .
Fit the runner to the right side .
The 1st screw uses the 2nd hole in from the front of the runner.
The 2nd and 3rd screws . use the holes that line up with the other panel holes.
Fit a screw into the 2nd hole in at the top of the runner .
A
2
B
2
M b
2
G
G
H
M b
2
Green edge
Green
edge
Green
edge
Green
edge
Assembly Instructions
8
Step 12
Step 13
A
B
Fit the horizontal to the right side
Push the horizontal onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
2
5
B
B
5
Fit the left side
Push the left side onto the horizontal .
Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .
Step 14
Prepare the top
Screw 4 metal dowels into the top .
5
1
B
5
A
A
A
A
A
3
Green
edge
2
5
5
1
3
Green
edge
Assembly Instructions
9
Step 15
Step 16
Fit the top
Push the top onto the assembly.
Use a screwdriver to tighten the 4 large locking nuts fitted to the left side and right side .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
B
3
2
1
A
B
B
3
1
2
Fit the base
Fit the base onto the assembly using 4 screws . .
4
E
E
E
E
E
Green
edge
4
Assembly Instructions
10
Step 17
Step 18
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
11
D
11
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
y
y
x
x
b:
D
11
Fit the feet
Fit the feet to the base using screws .
F
N
4
F
F
N
F
F
N
F
F
N
F
F
N
4
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR3041
Step 19
Fit the drawer
Slide the wheels of the runners fitted to the drawer, over the wheels of the runners fitted to the side panels and push the drawer into position.
Assembly is complete
Side
panel
Drawer
Loading...