MADE IN
BRITAIN
Dimensions
Width - 75cm
Depth - 50cm
Height - 184cm
Zest - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 02/10/14
Important - Please read these instructions fully before starting assembly
228/4587
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 44.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
2
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
3
Left Side (DF222)
(1782 x 495mm)
Right Side (DF223)
(1782 x 495mm)
Top (DF224)
(746 x 496mm)
Small Door (DF226)
(1808 x 280mm)
Base (DF225)
(746 x 496mm)
Back (X1808-740)
(1808 x 740mm)
8 9 10
Hanging Rail (FHR704)
(704mm long)
6
7
Handle (DPF05)
(591mm long) x 2
Back Rail (DF1437)
(712 x 124mm)
5
Large Door (DF227)
(1808 x 440mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B C
D F
G H I
Nail (F51) x 34
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
L
13mm Screw (F63) x 14
Metal dowel (F901) x 12
Large locking
nut (F900) x 12
13mm Screw (F79) x 1
K
Foot
(F233) x 4
Hinge (F520) x 6
Hinge Plate
(F521) x 6
Rail holder
(F1014) x 2
25mm Screw (F50) x 6
Bracket (F327) x 1
E
38mm Screw (F81) x 8
Green
edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Prepare the left side
Screw 2 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 4 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Push a rail holder into
the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates to
the left side making
sure that the slot is
facing towards the
finished front edge.
B
1
1
Step 1
Step 2
J
B
B
B
B
B
B
C
H
J
J
J
1
C
H
J
1
Prepare the right side
Screw 2 metal dowels
into the right side .
Insert 4 large locking
nuts into the right
side .
Push a rail holder into
the right side and
secure it with screw .
Fit 3 hinge plates to
the right side .
B
2
2
C
H
J
2
B
B
B
B
J
J
J
J
C
H
2
Green
edge
A
A
A
A
A
1
A
2
A
Green
edge
Green
edge
Assembly Instructions
5
Step 3
Step 4
Fit the back rail to the
left side
Push the back rail
onto the left side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the back rail .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Finished
top edge
Prepare the back rail
Insert 4 large locking
nuts into the back rail
. .
B
B
B
Finished
top edge
B
B
5
5
Plain chipboard
surface
5
1
5
B
B
5
Step 5
Fit the right side
Push the right side
onto the back rail .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the back rail .
5
2
B
5
2
5
E
B
2
Assembly Instructions
6
Step 6
Step 7
Fit the top
Push the top onto
the sides and .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each side and .
1 2
3
Prepare the top
Screw 4 metal dowels
into the top .
A
3
A
A
A
A
3
Green
edge
3
1
Green
edge
B
1 2
Assembly Instructions
7
Step 8
Prepare the base
a: Fit the feet to the
base using screws .
Turn the base over
b: Screw 4 metal
dowels into the base
. .
B
B
B
B
Turn the base over
4
4
A
4
Green
edge
E
L
4
Green
edge
2
4
Green
edge
Step 9
Fit the base
Push the base onto
the left side and right
side .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left side and right
side .
1
2
2
4
B
1
1
L
E
E
L
E
E
L
E
E
L
E
E
Green
surface
White
surface
Assembly Instructions
8
Step 10
Step 11
yy
xx
yy
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Stand the unit up for
the next step.
10
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
D
10
Warning: The
unit is heavy.
Lift with care.
6
C
Fit the hanging rail
Push the hanging rail
into the rail holders
fitted to the side panels.
6
C
xx
6
Assembly Instructions
9
Step 12
Step 13
Fit the handles to the
doors
Line up the holes in the
handle with the holes
in the small door and
secure with 3 screws .
Line up the holes in the
handle with the holes
in the large door and
secure with 3 screws .
F
7
8
F
7
9
F
F
F
7
9
8
7
90
K
Prepare the doors
Push fit 3 hinges into
the small door and
the large door .
Secure each hinge
with 2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
8
9
K
K
H
K
H
H
K
H
H
K
H
H
K
H
H
K
H
H
K
H
H
8
9
F
F
F
7
Assembly Instructions
8
Step 14
e:
a: b:
c: d:
B
J
K
A
J
K
J
J
K
K
K
J
B
Fit the doors
Note: The easiest way to
attach each door and
. is to fit the top hinge
first, then align and fit the
other hinge.
a: Push the hinge
onto the front part of the
hinge plate .
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
K
K
K
J
J
J
K
J
8
9
9
8
Note: The doors can go on
either side. The diagram shows
the small door on the left.
Assembly Instructions
11
Step 15
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the top (or
base) of the unit is level,
front-to-back and sideto-side in the 3 positions
shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
12
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 16
Top of Unit
WALL
WALL
Back of Unit
Fit the bracket
To prevent possible
overbalancing, we
recommend that this unit
is secured to a suitable
wall by use of the
bracket fitted to the
top of the unit.
Fixings are not supplied,
as they will need to suit
the wall type and the
length of screw will
depend on the distance
from the back of the unit
to the wall.
Fix the bracket
loosely onto the top of
the unit using screw
and mark the wall for the
wall fixing.
Swivel the bracket
away from the wall and
drill a hole in the wall
using a suitable drill bit
and fit your wall fixing.
Swivel the bracket
back and fix the bracket
to the wall, then tighten
screw .
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Warning: The
unit is heavy.
Lift with care.
Assembly is complete
I
I
G
I
I
G
I
G
I
I
ALR3045
Loading...