Argos ZDV4D2-DLO-AR, Denver - 4 Drawer Chest ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 75cm
Depth - 40cm
Height - 93cm
Denver - 4 Drawer Chest
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 20/10/14
Important - Please read these instructions fully before starting assembly
355/8463
332/4790
333/7062
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 29kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the overbalance kit supplied.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
3
5 6 7
8
9 10
Top (D1567A)
(718 x 395mm)
Left Side (DF2098A)
(930 x 396mm)
4
Drawer Base (T697-367)
(697 x 367mm) x 4
Left Drawer Side (W370-124LH)
(370 x 124mm) x 4
Drawer Front (DF2092A)
(742 x 192mm) x 4
Rail (D1570A)
(718 x 60mm) x 4
Right Drawer Side (W370-124RH)
(370 x 124mm) x 4
Right Side (DF2099A)
(930 x 396mm)
Drawer Back (W686-124)
(686 x 124mm) x 4
Back (X848-744)
(848 x 744mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 20
C
D E F
G
J
H
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Small locking nut (F3) x 8
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
9mm Screw (F74) x 8 9mm Screw (F73) x 16
Drawer runner (F1004) x 8
Large locking nut (F900) x 12
Nail (F51) x 20
K
Electric drill (do not use for fitting screws)
I
Wedgefix (F639) x 16
Plastic Nail (F91) x 4
L
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Knock-in Peg (F171GY) x 16
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 4
x 4
x 4
x 4
5
B
B
B
C
C
C
C
6
7
Step 2
Prepare the 4 drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
5
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
6
7
Attach the drawer sides to the drawer front
Push the left drawer sides . and right drawer sides . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
6 7
5
C
C
6 7
6
7
B
B
5
Assembly Instructions
5
Step 4
H
H
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
9
6 7
5
8
6 7
9
8
8
H
6 7
Step 6
Fit the wedgefixes
Turn the drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
K
H
H
K
K
K
K
K
9
6
8
6
7
9
7
5
x 4
x 4
x 4
Finished
front edge
Assembly Instructions
6
Step 7
Finished
front edge
F
J
Prepare the left side
a: Place 4 runners on
the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
Screw 6 metal dowels into the left side .
1
F
F
1
J
J
B
1
a:
b:
F
J
F
F
F
F
B
Finished
front edge
F
J
F
J
F
J
B
B
B
B
B
1
1
Finished
front edge
F
J
Step 8
Prepare the right side
a: Place 4 runners on
the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
Screw 6 metal dowels into the right side .
2
F
F
2
J
J
B
2
F
J
F
J
B
F
J
F
J
F
F
F
F
B
B
B
B
B
Finished
front edge
Finished
front edge
2
2
A
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 9
Step 11
Prepare the top
Insert 4 large locking nuts into the top .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
D
D
3
D
D
D
D
Finished
front edge
Step 10
Fit the top to the right side
Push the top onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the top .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
3
3
2
D
D
B
D
3
3
2
D
D
x 4
Prepare the 4 rails
Insert 2 large locking nuts into each of the 4 rails .
Tap 2 wooden dowels into each of the 4 rails .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
D
4
4
A
10mm
A
A
4
Assembly Instructions
8
Step 12
Step 13
2
4
4
4
2
Fit 3 of the rails
Push 3 rails onto the right side .
Use a screwdriver to tighten the 3 large locking nuts fitted to the 3 rails .
4
2
D
4
Fit the last rail
Push the last rail onto the right side .
Use a screwdriver to tighten the large locking nut fitted to the last rail .
4
2
D
4
Note: Support this rail until the left side has been fitted in the next step.
4
Step 14
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 6 large locking nuts fitted to the top and rails .
1
D
3 4
4
4
4
4
3
1
yy
Assembly Instructions
9
Step 15
Step 16
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be evenly spaced out.
10
G
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
xx
yy
xx
b:
G
10
Fit the 4 plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . .
Stand the unit up for the next step.
I
1
2
I
I
I
I
2
1
Assembly Instructions
10
Step 17
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides . and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
E
J
J
E
76
2nd threaded
hole
J
E
E
E
6
7
Assembly Instructions
11 ALR3094
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 14
Fit the overbalance protector
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the overbalance protector kit . fitted to the unit or, an alternative fixing method of your choice.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Assembly is complete
L
Attach the
strap to the unit
Attach the
strap to the wall
Wall fixing
(not supplied)
Washer
Strap
Strap
L
L
Example
Screw
(not supplied)
Washer
Screw
UNIT
Loading...