Argos ZDV22R2-WO-AR, Denver - 2 Drawer 2 Door Robe ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 3 - 16/01/15
Important - Please read these instructions fully before starting assembly
Denver - 2 Drawer 2 Door Robe
Dimensions
Width - 75cm
Depth - 50cm
Height - 181cm
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 52kgs. Please lift with care.
• Check you have all the components and tools listed on pages 1, 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Tools required
Rule
Scissors
Spirit level
Hammer Bradawl
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Step ladder
Electric drill (only use when drilling into walls)
Square
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
1 2
4
3
Hanging Rail (FHR710)
(710mm long)
5
10
9
6
12
11
87
13
Top/Base (D1574A)
(718 x 494mm) x 3
Left Side (DF2091A)
(1808 x 496mm)
Rail (D1570A)
(718 x 60mm) x 2
Right Side (DF2093A)
(1808 x 496mm)
Door (DF2094A)
(1338 x 355mm) x 2
Vertical Rail (DF2095A)
(1306.5 x 88mm)
Drawer Back (W686-124)
(686 x 124mm) x 2
Drawer Base (T697-367)
(697 x 367mm) x 2
Left Drawer Side (W370-124LH)
(370 x 124mm) x 2
Drawer Front (DF2092A)
(742 x 192mm) x 2
Right Drawer Side (W370-124RH)
(370 x 124mm) x 2
Back (X1779-744)
(1779 x 744mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 20
C
D E F
G
P
H
Small locking nut (F3) x 4
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Drawer runner (F1004) x 4
Large locking nut (F900) x 16
M
I
KJ
9mm Screw (F74) x 4 9mm Screw (F73) x 8
Nail (F51) x 26
L
N
Rail holder
(F1014) x 2
40mm Screw (F910) x 4
13mm Screw (F63) x 14
Hinge (F518) x 6
Hinge plate (F523) x 6
O
Knock-in Peg (F171GY) x 8
Wedgefix (F639) x 8
Plastic Nail (F91) x 4
Q
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 2
x 2
x 2
x 2
6
B
B
B
C
C
C
C
7
8
Step 2
Prepare the 2 drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
6
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
7
8
Attach the drawer sides to the drawer front
Push the left drawer sides . and right drawer sides . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
7 8
6
C
C
7 8
7
8
B
B
6
Loading...
+ 11 hidden pages