Argos ZCVD3R-BLO-AR, ZCVD3R-WM-AR, ZCVD3R-WO-AR, ZCVD3R-FE-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 103cm

Depth - 49.5cm

Height - 200cm

Cheval - 3 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 08/09/14

Important - Please read these instructions fully before starting assembly

147/9489

147/7807

141/2219

152/5326

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 67kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Tools required

Rule

Scissors

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Step ladder

Electric drill (only use when drilling into walls)

Square

100

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

1 2 3

Door (D2725A)

(1888 x 337mm) x 3

13 14

Large Hanging Rail (FHR646)

(646mm long)

Small Hanging Rail (FHR317)

(317mm long) x 2

Left Side (D2720A)

(1981 x 458mm)

Right Side (D2726A)

(1981 x 458mm)

Large Horizontal (D2722A)

(654 x 456mm)

Plinth (D2729A)

(995 x 86mm)

Top (D2727A)

(1030 x 494mm)

Base (D2733A)

(995 x 456mm)

Upright (D2731A)

(1879 x 455mm)

Small Back (X1890-345)

(1890 x 345mm)

Large Back (X1890-674)

(1890 x 674mm)

Small Horizontal (D2732A)

(325 x 456mm)

Rail (D2724A)

(654 x 86mm) x 2

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Wooden dowel (F22) x 26

Metal dowel (F901) x 18

D E

Large locking nut (F900) x 18

G H I

Nail (F51) x 39

Rail Holder (F891) x 6

19mm Screw (F461) x 6

13mm Screw (F63) x 3013mm Screw (F79) x 1

Bracket (F327) x 1

Handle (F274) x 3

40mm Screw (F910) x 8

Hinge (F518) x 9

Hinge plate (F523) x 9

Plastic Nail (F91) x 4

Nail screw (F277) x 5

Back holder (F276) x 5

* These can also be round

Finished

front edge

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Prepare the upright

a: Tap 4 wooden dowels

. into the upright .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Screw 2 metal dowels into the upright .

Note: Tighten the metal dowels up fully against the panels.

Fit 2 rail holders to the upright using 2 screws in each.

Turn the upright over

b: Screw 4 metal dowels

. into the upright .

Fit 3 hinge plates onto the upright , making sure that the slot is facing towards the finished front edge.

Fit a rail holder to the upright using 2 screws .

To fit the rail holder, screw through its top hole and into the shallow mark hole drilled in the panel. Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

10mm

Turn the upright over

Finished

front edge

+ 11 hidden pages