Argos ZCVD1CMR-BLO-AR, ZCVD1CMR-MW-AR, ZCVD1CMR-WO-AR, ZCVD1CMR-FE-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 65cm

Depth - 65cm

Height - 200cm

Cheval - Corner Mirror Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 25/07/14

Important - Please read these instructions fully before starting assembly

151/5556

147/3533

152/6882

151/2999

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 51kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

1

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.

• Dispose of all packaging
carefully and responsibly.

Note: If required the next page can be
cut out and used as reference throughout
the assembly. Keep this page with these
instructions for future reference.

IMPORTANT INFORMATION ABOUT THIS PRODUCT

This product complies with the requirements of BS 7449:1991 and has been manufactured by

DECORATIVE PANELS FURNITURE LTD, TEESSIDE INDUSTRIAL ESTATE,

THORNABY-ON-TEES, CLEVELAND, TS17 9LT

.

The product code for this unit and the item code(s) for the glass components are listed in the Assembly

Instructions along with a description of the type of glass used. All clear/tinted glass complies with the
requirements of BS 6206 Class A. All mirrors comply with the requirements of BS 6206 Class C. If the

glass component contained in this unit is chipped or broken consult the furniture manufacturer, retailer,

or agent with regard to obtaining a manufacturing specification and shape for replacement glass

quoting the unit description and batch number or date of manufacture.

Do not place very hot or very cold items against or in close proximity to glass surface(s) unless

adequately thick insulating material is used to prevent such items coming in contact with the glass.

Do not strike the glass with hard or pointed items.

Do not sit or stand upon horizontal glass surfaces.

When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if

necessary - do not use washing powders or any other substance containing abrasives since these

substances scratch glass.

If stated in the instruction leaflet, it is essential that this unit is fixed to a wall.

KEEP THESE INSTRUCTIONS FOR FUTURE USE

Components - Panels

Please check you have all the panels listed below

2

1

2 3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D2739A)

(1981 x 400mm)

Right Side (D2740A)

(1981 x 400mm)

9

4

Plinth (D2742A)

(86 x 344mm)

Base (D2744A)

(634 x 634mm)

Top (D2745A)

(650 x 650mm)

The 2 triangular pieces are not used.
They are for packing purposes only.

Support (D2743A)

(86 x 637mm)

Shelf (D2746A)

(617 x 300mm)

Right Back (D2747A)

(1879.5 x 330mm)

8

10

1211

Left Back (D2748A)

(1879.5 x 330mm)

6 7

5

Back (X1900-350)

(1900 x 350mm) x 2

Hanging Rail (FHR609)

(609mm long)

Mirror Door (D2741MA)

(1888 x 331mm)

(Mirror - SG24
1817 x 260mm
Safety Back SAR)

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

A

Wooden dowel (F22) x 12

B

Metal dowel (F901) x 8

C

D E

Large locking
nut (F900) x 8

F

G H I

L

Nail (F51) x 37

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J

P

M

K

Rail Holder
(F891) x 2

19mm Screw (F461) x 2

13mm Screw (F63) x 1013mm Screw (F79) x 9

Bracket (F327) x 1

Handle (F274) x 1

Tools required

Rule

Scissors

Spirit
level

Hammer Bradawl

Eye protection
(when using a
hammer or drill)

Cross-head
screwdriver

Step
ladder

Electric drill
(only use
when drilling
into walls)

Square

mm

10

20

30

40

50

60

70

80

90

100

mm

10

20

30

40

50

60

70

80

90

100

40mm Screw (F910) x 12

Hinge (F321) x 3

Hinge plate
(F322) x 3

N

Mini block (F25) x 3

O

Shelf stud (F110) x 4

Plastic Nail (F91) x 7

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

4

Prepare the base

Tap 4 wooden dowels
into the base .

Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.

Insert 4 large locking
nuts into the base .

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

Turn the base over

Screw 4 metal dowels
into the base .

Note: Tighten the metal
dowels up fully against
the panels.

CC

C C

A

A

A

A

Prepare the plinth and
the support

Tap 2 wooden dowels
into the plinth .

Tap 2 wooden dowels
into the support .

A

A

9

A

A

A

A

9

10

10

Step 2

5

A

C

C

B

10mm

A

5

Note: The base can have
a plain chipboard surface.

Note: The plinth can have
a plain chipboard surface.

Note: The colour of the
support may differ from
the main unit colour or
may be plain chipboard.

Plain

chipboard

surface

B

B

B

B

Turn the

base over

5

B

Assembly Instructions

5

Prepare the right back

Insert 2 large locking
nuts into the right
back .

If required, to fit the rail
holder , screw through
the top hole with screw
and into the mark hole
drilled in the right back
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using the lower hole.

Step 3

Step 5

Step 4

Fit the plinth to the
base

Push the plinth onto
the base and fit it
using 2 screws .

9

5

E

E

E

9

5

E

10

5

Fit the support to the
base

Push the support
onto the base and fit
it using 2 screws .

10

5

E

E

C

7

Finished

front edge

C

C

7

H

H

I

H

H

7

Important: The plain
chipboard surface
must be at the back.

Only fit the rail

holder to the

right back if you

want the hanging

rail to go across

the robe this way

7

I

Finished

front edge

Assembly Instructions

6

Step 6

Fit the right back

Push the right back
onto the 2 metal dowels
fitted to the base .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right back .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

7

5

C

C

7

Prepare the left back

Insert 2 large locking
nuts into the left
back .

Gently tap the 3 mini
blocks into the holes
on the left back ,
orientated as shown.

If required, to fit the rail
holder , screw through
the top hole with screw
and into the mark hole
drilled in the left back .
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.

C

6

Step 7

N

6

N

6

C

C

N

N

N

6

Finished

front edge

7

Only fit the rail
holder to the left
back if you want

the hanging rail

to go across the

robe this way

6

H

H

I

I

H

H

7

Assembly Instructions

7

Step 8

Step 9

Fit the left back

Push the left back
onto the 2 metal dowels
fitted to the base .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left back .

Tighten up the screws in
the 3 mini blocks into
the holes in the right
back .

6

5

C

6

6

7

N

7

Finished

front edge

Only fit the hinges

to the right side if

you want your door

to open this way

A

A

B

B

Prepare the right side

If required, fit 3 hinge
plates onto the right
side making sure that
the longer part is facing
towards the finished
front edge.

Screw 2 metal dowels
into the right side .

Tap 2 wooden dowels
into the right side .

If required, to fit the rail
holder , screw through
the top hole with screw
and into the mark hole
drilled in the right side .
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.

K

2

B

2

A

2

Finished

front edge

2

Only fit the rail

holder to the right

side if you have

fitted a rail holder

to the left back

6

2

H

H

I

I

H

H

2

5

K

K

K

K

Assembly Instructions

8

Step 10

Step 11

Fit the right side

Push the right side
onto the base .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the bottom of the base
. .

2

5

2

5

5

C

Finished

front edge

E

Fit the top

Attach the top
to the right side ,
left back and
right back with
6 screws .

E

E

E

E

E

4

2

6

7

E

4

2

6

7

Finished

front edge

9

Step 12

Step 13

B

B

A

A

Prepare the left side

If required, fit 3 hinge
plates onto the left
side making sure that
the longer part is facing
towards the finished
front edge.

Screw 2 metal dowels
into the left side .

Tap 2 wooden dowels
into the left side .

If required, to fit the rail
holder , screw through
the top hole with screw
and into the mark hole
drilled in the left side .
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.

K

1

B

1

A

1

1

Fit the left side

Push the left
side up into
the top and onto
the base and secure
it to the top with
2 screws .

Use a screwdriver
to tighten the 2
large locking nuts
. fitted to the
bottom of the base .

1

4

5

4

E

5

C

E

E

1

5

4

Only fit the hinges

to the left side if

you want your door

to open this way

Only fit the rail

holder to the left

side if you have

fitted a rail holder

to the right back

7

K

1

I

H

H

1

H

H

I

Finished

front edge

Assembly Instructions

K

K

K

Assembly Instructions

10

Step 14

Step 15

Warning: The
unit is heavy.
Lift with care.

Fit a back

Carefully roll the unit
over, as shown.

Place a back onto
the unit so it is flush with
the back edges of the
top , base and left
side .

Using half the total
quantity of nails , nail
the top onto the back
edges of the top, base
and left side.

Note: Nails should be
evenly spaced apart.

Secure the back to
the left back using 4
screws .

Note: DO NOT nail
into the left back .

G

G

G

G

12

4

1

5

12

4

1

5

D

D

12

6

G

6

Roll the unit over

Warning: The

unit is heavy.
Lift with care.

Roll the unit over

12

6

Fit the other back

Carefully roll the unit
over again, as shown.

Place a back onto
the unit so it is flush with
the back edges of the
top , base and
right side .

Using the rest of the
nails , nail into the
back edges of the top,
base and right side.

Note: Nails should be
evenly spaced apart.

Secure the back to
the right back using
4 screws .

D

G

G

G

G

12

4

2

5

D

12

7

G

12

4

2

5

7

Note: DO NOT nail
into the right back .

7

Assembly Instructions

11

Step 16

Step 17

Fit the plastic nails

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. , 2 into the plinth
and 1 at the back of the
support , as shown.

Stand the unit up for
the next step.

P

P

1

2

10

9

P

P

P

P

P

P

Warning: The
unit is heavy.
Lift with care.

11

I

Fit the hanging rail

Push the hanging rail
into the rail holders .

The diagram shows the
rail being fitted to the left
hand side of the unit.
You may have chosen to
fit it to the right hand
side.

11

I

11

1

2

10

9

Assembly Instructions

Step 18

Fit the shelf

You can fit the shelf
on the left or the right of
the unit.

If you have chosen the
left, insert 2 shelf studs
into the left side and
2 into the right back
at the required height.
Insert the shelf and lower
it onto the shelf studs.

If you have chosen the
right, insert 2 shelf studs
. into the right side
and 2 into the left back
at the required height.
Insert the shelf and lower
it onto the shelf studs.

O

x 4

O

x 4

8 8

8

O

1

7

O

2

6

1

7

2

6

Shelf on the left

OR

Shelf on the right

H

H

L

H

H

L

H

H

L

90

L

Prepare the door

Push fit the 3 hinges
into the door .

Secure each hinge with
2 screws .

Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.

H

L

3

3

Step 19

12

Warning:
Glass! Handle
with care

Assembly Instructions

13

Step 20

Fit the door and
handle

Note: The easiest way to
attach the door is to
fit the top hinge first,
then align and fit the
other hinges.

a: Push the slotted part

of the hinge over the
centre screw on the
hinge plate .
Keep the hinge flat
against the hinge plate
as you slide it across as
far as it will go.

b: When the hinge

has been pushed fully
onto the hinge plate ,
tighten screw A.

c: Attach the handle

to the door using 2
screws .

Note: This shows the door
being fitted to the right side.
You may have chosen to fit
it to the left side.

L

L

K

3

A

a: b:

L

K

F

M

3

L

K

L

K

Warning:
Glass! Handle
with care

F

F

M

c:

3

Assembly Instructions

Step 21

14

Adjust the door if
needed

a: Before adjusting the

door, use a spirit level to
check the top (or base)
of the unit is level, front­to-back and side-to-side
in the 2 positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.

b: Height adjustment.

Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.

c: Forward and Back

adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.

d: Sideways

adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.

a:

A

A

b:

c:

d:

B

C

Assembly Instructions

15

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

ALR2967

Step 22

Top of Unit

WALL

WALL

Back of Unit

Fit the bracket

To prevent possible
overbalancing, we
recommend that this unit
is secured to a suitable
wall by use of the
bracket fitted to the
top of the unit.

Fixings are not supplied,
as they will need to suit
the wall type and the
length of screw will
depend on the distance
from the back of the unit
to the wall.

Fix the bracket
loosely onto the top of
the unit using screw
and mark the wall for the
wall fixing.

Swivel the bracket
away from the wall and
drill a hole in the wall
using a suitable drill bit
and fit your wall fixing.

Swivel the bracket
back and fix the bracket
to the wall, then tighten
screw .

Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.

Warning: The
unit is heavy.
Lift with care.

Assembly is complete

J

J

G

J

J

G

J

G

J

J

Note: The bracket can
be fitted on either side.
This shows it being fitted
to the left hand side.