Argos ZCVBS-FE-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 38.5cm

Depth - 36cm

Height - 58cm

Cheval - Bedside

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 13/03/14

Important - Please read these instructions fully before starting assembly

147/3100

152/7939

146/1480

152/8794

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 12kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

2

1

2 3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Top (D2734A)

(383 x 360mm)

Right Side (D2735A)

(562 x 318mm)

Rail (D2737A)

(348 x 66mm) x 2

Drawer Front (D2738A)

(364 x 164mm) x 3

Drawer Base (T322-297)

(322 x 297mm) x 3

Back (X515-370)

(515 x 370mm)

Left Drawer Side (W300-124LH)

(300 x 124mm) x 3

Right Drawer Side (W300-124RH)

(300 x 124mm) x 3

Left Side (D2736A)

(562 x 318mm)

4

5

6

7 8 9

10

Drawer Back (W311-124)

(311 x 124mm) x 3

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 4

B

Metal dowel (F901) x 14

D E

Large locking nut (F900) x 8

F

G H I

K

Small locking nut (F3) x 6

C

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J

9mm Screw (F74) x 6 9mm Screw (F73) x 12

L

Knock-in Peg (F171) x 12

Plastic Nail (F91) x 4

Drawer runner (F1004) x 6

Handle (F273) x 3

19mm Screw (F461) x 6

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Nail (F51) x 12

M

Wedgefix (F639) x 6

5

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 3

B

E

Step 2

Prepare the 3 drawer fronts

Screw 2 metal dowels into each of the 3 drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

B

5

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

E

7

8

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

7 8

5

E

7 8

E

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

E

7

8

B

5

7

8

K

5

Assembly Instructions

5

Step 4

K

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 7

9

7 8

5

6

7 8

9

6

K

7 8

K

x 3

9

7

8

7

8

9

6

K

Step 6

Attach the handle

Attach a handle to each drawer front using 2 screws .

L

G

5

x 3

5

G

L

M

Fit the wedgefixes

Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

M

Finished

front edge

Assembly Instructions

6

Step 8

Finished

front edge

I

J

I

J

I

J

I

J

D

I

D

Prepare the left side

a: Place 3 runners on

the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the left side .

c: Screw 2 metal

dowels into the left side .

Insert 2 large locking nuts into the left side . .

Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.

1

I

D

1

J

B

1

a:

b:

c:

B

1

Assembly Instructions

7

Step 9

Finished

front edge

I

J

Finished

front edge

I

J

I

J

I

J

Finished

front edge

Finished

front edge

D

B

Prepare the right side

a: Place 3 runners on

the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the right side .

c: Screw 2 metal

dowels into the right side .

Insert 2 large locking nuts into the right side .

2

I

D

2

J

B

2

a:

b:

c:

2

I