Argos CHEVAL, ZCV52D-BLO-AR, ZCV52D-MW-AR, ZCV52D-WO-AR, ZCV52D-FE-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 71cm

Depth - 36cm

Height - 107cm

Cheval - 5+2 Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 13/03/14

Important - Please read these instructions fully before starting assembly

146/3093

151/4186

145/2561

147/2558

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 31kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

2 4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D2749A)

(1054 x 318mm)

Right Side (D2750A)

(1054 x 318mm)

Upright (D2752A)

(167 x 318mm)

3

Top (D2751A)

(710 x 360mm)

Large Drawer Front (D2753A)

(692 x 164mm) x 5

Left Drawer Side (W300-124LH)

(300 x 124mm) x 7

Right Drawer Side (W300-124RH)

(300 x 124mm) x 7

Small Drawer Back (W293-124)

(293 x 124mm) x 2

Large Drawer Back (W639-124)

(639 x 124mm) x 5

Small Left DrawerFront (D2754A)

(344 x 164mm)

Small Right Drawer Front (D2770A)

(344 x 164mm)

Rail (D2755A)

(675 x 66mm) x 2

Small Drawer Base (T304-297)

(304 x 297mm) x 2

Large Drawer Base (T650-297)

(650 x 297mm) x 5

Back (X1007-700)

(1007 x 700mm)

5

8

6 7

9 10

11 12

13 14

15

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Electric drill (do not use for fitting screws)

A

Wooden dowel (F22) x 4

B

Metal dowel (F901) x 24

D E

Large locking nut (F900) x 10

F

G H

M

I

K

Small locking nut (F3) x 14

C

J

9mm Screw (F74) x 14 9mm Screw (F73) x 28

L N

Knock-in Peg (F171) x 28

Plastic Nail (F91) x 4

Drawer runner (F1004) x 14

Handle (F273) x 7

19mm Screw (F461) x 14

Nail (F51) x 23

Wedgefix (F639) x 24

O

13mm Screw (F79) x 1

Bracket (F327) x 1

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 2

B

E

Step 2

Prepare the small left and right drawer fronts

Screw 2 metal dowels into the small left drawer front and the small right drawer front .

Note: Tighten the metal dowels up fully against the panels.

B

9

10

Prepare 2 pairs of drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

E

6

7

Attach the drawer sides to the small drawer fronts

Push the left drawer side . and right drawer side . onto the back of the 2 small drawer fronts and .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

6 7

9

10

E

6 7

E

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

E

6

7

B

9 10

6

7

Note: The small right drawer front has a shallow identification mark.

Assembly Instructions

5

Step 4

N

Fit the small drawer base

Slide the small drawer base down the grooves in the drawer sides and and down into the groove in the small drawer fronts . and .

Step 5

Fit the small drawer back

Fit the small drawer back . between the drawer sides and .

Make sure that the small drawer base fits into the groove in the small drawer back .

Hold the small drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

13

6 7

9 10

6

12

7

13

12

N

6 7

Attach the handle

Attach a handle to each small drawer front . and using 2 screws .

L

G

9 10

N

x 2

13

6

7

N

9 10

6

12

13

7

G

L

9 10

Step 7

x 2

M

Fit the wedgefixes

Turn the 2 small drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

M

8

Assembly Instructions

6

Step 8

x 5

B

E

Step 9

Prepare the 5 large drawer fronts

Screw 2 metal dowels into each of the large drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

B

8

Prepare 5 pairs of drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 10

E

6

7

Attach the drawer sides to the large drawer fronts

Push the left drawer side . and right drawer side . onto the back of the 5 large drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

6 7

8

E

6 7

E

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

E

6

7

6

7

B

8

Assembly Instructions

7

Step 11

N

Fit the large drawer base

Slide the large drawer base down the grooves in the drawer sides and and down into the groove in the large drawer front .

Step 12

Fit the large drawer back

Fit the large drawer back . between the drawer sides and .

Make sure that the large drawer base fits into the groove in the large drawer back .

Hold the large drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 13

14

6 7

8

6

11

7

14

11

N

6 7

Attach the handle

Attach a handle to each large drawer front . using 2 screws .

Step 14

L

G

8

N

x 5

14

6

7

N

6

11

14

7

M

Fit the wedgefixes

Turn the large drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

M

G

L

8

Assembly Instructions

8

Step 15

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

I

J

D

Prepare the left side

a: Place 6 runners on

the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the left side .

c: Screw 2 metal

dowels into the left side .

Insert 2 large locking nuts into the left side . .

Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.

1

I

D

1

J

B

1

b:

a:

c:

I

J

I

J

I

J

I

J

I

J

I

J

1

I

B

D

Assembly Instructions

9

Step 16

Finished

front edge

I

J

Prepare the right side

a: Place 6 runners on

the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the right side .

c: Screw 2 metal

dowels into the right side .

Insert 2 large locking nuts into the right side .

2

I

D

2

J

B

2

a:

b:

c:

Finished

front edge

Finished

front edge

Finished

front edge

I

J

I

J

I

J

I

J

I

J

I

J

I

B

D

2

A

Assembly Instructions

10

Step 17

10mm

A

Prepare the 2 rails

Tap 2 wooden dowels into each rail .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Insert 2 large locking nuts into each rail .

A

5

D

5

Fit the 2 rails

Push the 2 rails onto the right side .

Use a screwdriver to tighten the large locking nut fitted to each rail . .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

D

5

Step 18

D

B

5

2

D

Fit the left side

Push the left side onto the 2 rails .

Use a screwdriver to tighten the large locking nut fitted to each rail . .

D

5

Step 19

1

5

D

A

x 2

Note: Support this rail until the left side has been fitted in the next step.

5

2

5

1

plain chipboard surface

5

plain chipboard surface

Finished

front edge

Assembly Instructions

11

Step 20

Prepare the upright

Note: The colour of the upright may differ from the main unit colour or may be plain chipboard.

a: Place a runner on

the upright as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

Insert 2 large locking nuts into the upright . .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the upright .

Turn the upright over

c: Place a runner on

the upright as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

d: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the upright .

4

I

D

4

J

4

I

J

I

4

J

Finished

front edge

I

J

Turn the upright over

a:

b:

c:

d:

Note: Due to the manufacturing process, the 2 holes for the large locking nuts can be on either surface of the upright.

Finished

front edge

I

J

I

J

D

4

Finished

front edge

4

Finished

front edge

I

Finished

front edge

I

J

I

4

Assembly Instructions

12

Step 21

Step 22

B

Finished

front edge

Prepare the top

Screw 6 metal dowels into the top .

B

3

Fit the upright and bracket to the top

Push the upright down onto the top .

Use a screwdriver to tighten the 2 large locking nuts fitted to the upright .

Fix the bracket to the top , 175mm in from the side and flush to the back edge, using screw . .

Step 23

D

O

3

4

Remember: The 2 holes for the large locking nuts can be on either surface of the upright.

Finished

front edge

3

4

1

K

O

175mm

O

3

K

Fit the top

Push the top onto the sides and .

Use a screwdriver to tighten the 2 large locking nuts fitted to each side and .

3

1 2

D

1 2

3

2

Assembly Instructions

13

Step 24

y

x

b:

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the outside edges of the back .

Note: Nails should be spaced about 150mm apart.

Stand the unit up for the next step.

15

C

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

15

C

15

Step 25

Fit the plastic nails

Tap 2 plastic nails into the bottom edge of each of the sides and . as shown.

Carefully stand the unit up for the next step.

F

1

2

F

1

2

Assembly Instructions

14

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Step 26

O

Secure unit to a wall

To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the metal bracket fitted to the top .

Fixings are not supplied as they will need to suit the wall type, and the length of screw will depend on the distance of the back of the unit to the wall.

3

WALL

O

3

O

Step 27

Fit the drawers

Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .

Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.

Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.

Assembly is complete

H

J

H

2nd threaded

hole

J

H

7 8

Warning: Take care when

drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

Top of unit

H

ALR2969

Argos CHEVAL, ZCV52D-BLO-AR, ZCV52D-MW-AR, ZCV52D-WO-AR, ZCV52D-FE-AR ASSEMBLY INSTRUCTIONS

Specifications and Main Features

Frequently Asked Questions

User Manual