MADE IN
BRITAIN
Dimensions
Width - 71cm
Depth - 36cm
Height - 73cm
Cheval - 4 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 13/06/14
Important - Please read these instructions fully before starting assembly
258/7260
274/9981
275/2514
268/9254
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 22kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
2 3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (D2966A)
(720 x 318mm)
4
Right Side (D2967A)
(720 x 318mm)
Top (D2751A)
(710 x 360mm)
5
Large Drawer Front (D2753A)
(692 x 164mm) x 4
9
Left Drawer
Side (W300-124LH)
(300 x 124mm) x 4
Right Drawer
Side (W300-124RH)
(300 x 124mm) x 4
Large Drawer
Back (W639-124)
(639 x 124mm) x 4
Rail (D2755A)
(675 x 66mm) x 2
Large Drawer Base (T650-297)
(650 x 297mm) x 4
6
7
8
10 Back (X700-672)
(700 x 672mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Electric drill
(do not use for
fitting screws)
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 16
D E
Large locking
nut (F900) x 8
F
G H
M
I
K
Small locking
nut (F3) x 8
C
J
9mm Screw (F74) x 8 9mm Screw (F73) x 16
L N
Knock-in Peg (F171) x 16
Plastic Nail (F91) x 4
Drawer runner (F1004) x 8
Handle (F273) x 4
19mm Screw (F461) x 8
Nail (F51) x 16
Wedgefix (F639) x 16
O
13mm Screw (F79) x 1
Bracket (F327) x 1
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
5
x 4
x 4
x 4
x 4
B
E
Step 2
Prepare the 4 large
drawer fronts
Screw 2 metal dowels
into each of the large
drawer fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
5
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
E
7
8
Attach the drawer
sides to the large
drawer fronts
Push the left drawer side
. and right drawer side
. onto the back of the
4 large drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
8
5
E
E
7
8
E
E
E
7
8
7
8
B
B
5
B
Fit the large drawer
bases
Slide the large drawer
base down the
grooves in the drawer
sides and and
down into the groove in
the large drawer front .
Assembly Instructions
5
Step 4
5
N
N
Step 5
Fit the large drawer
back
Fit the large drawer back
. between the drawer
sides and .
Make sure that the large
drawer base fits into
the groove in the large
drawer back .
Hold the large drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
Step 6
9
7 8
5
7
6
8
9
6
6
N
7 8
Attach the handle
Attach a handle to
each large drawer front
. using 2 screws .
Step 7
L
G
5
N
x 4
x 4
x 4
x 4
9
7
8
N
7
6
9
8
M
M
M
M
M
Fit the wedgefixes
Turn the large drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
M
G
G
L
5
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 8
I
J
I
J
I
J
I
J
Finished
front edge
I
J
Prepare the left side
a: Place 4 runners on
the left side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Screw 2 metal
dowels into the left
side .
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
1
I
I
D
1
1
J
J
B
1
I
I
I
I
D
D
B
B
1
1
1
a:
b:
c:
D
Assembly Instructions
7
Step 9
Finished
front edge
I
J
Prepare the right side
a: Place 4 runners on
the right side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Screw 2 metal
dowels into the right
side .
Insert 2 large locking
nuts into the right
side .
2
I
I
D
2
2
J
J
B
2
I
J
I
J
I
J
I
J
I
I
I
I
D
D
B
B
Finished
front edge
Finished
front edge
Finished
front edge
2
2
2
a:
b:
c:
Assembly Instructions
8
Step 10
A
10mm
A
Prepare the 2 rails
Tap 2 wooden dowels
into each rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into each rail .
A
4
D
4
Fit the 2 rails
Push the 2 rails onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to each rail
. .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
D
4
Step 11
D
B
4
2
D
Fit the left side
Push the left side
onto the 2 rails .
Use a screwdriver to
tighten the large locking
nut fitted to each rail
. .
D
4
Step 12
1
4
D
D
A
x 2
plain chipboard surface
4
4
plain chipboard surface
plain chipboard surface
4
2
Note: Support this
rail until the left
side has been fitted
in the next step.
1
4
4
Assembly Instructions
9
Step 13
B
B
B
B
Finished
front edge
Prepare the top
Screw 4 metal dowels
into the top .
Fix the bracket in the
centre of the top and
flush to the back edge,
using screw .
B
3
3
K
O
O
3
K
O
3
1
2
Step 14
Fit the top
Push the top onto
the sides and .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each side and .
3
1 2
D
1 2
Assembly Instructions
10
Step 15
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
10
C
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
Step 16
Fit the plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. as shown.
Carefully stand the
unit up for the next
step.
F
1
2
b:
C
y
y
x
x
10
F
F
F
F
2
1
Warning: The
unit is heavy.
Lift with care.
Assembly Instructions
ALR306511
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 17
O
Secure unit to a wall
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by use of the metal
bracket fitted to the
top .
Fixings are not supplied
as they will need to suit
the wall type, and the
length of screw will
depend on the distance
of the back of the unit to
the wall.
3
Step 18
Fit the drawers
Starting with the bottom
drawer, slide both the
runners forward and
locate the drawer
sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .
Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.
Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.
Assembly is complete
H
J
H
H
2nd threaded
hole
J
H
7 8
O
WALL
WALL
O
Warning: Take
care when
drilling the wall
that you do not drill into
any pipes, wires etc. If in
doubt, consult an expert.
Top of unit
3
H
H
7
8
Loading...