Argos ZCP5D2-W-ARDO ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 63cm

Depth - 39cm

Height - 90.4cm

Capella - 5 Drawer Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 7 - 21/05/14

Important - Please read these instructions fully before starting assembly

262/0804

267/5660

266/7788

254/9703

227/4061

247/7284

266/5735

274/3877

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 27kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D1011A)

(904 x 390mm)

Top (D1008A)

(596 x 369mm)

Drawer Front (D1010A)

(592 x 157mm) x 5

Back (X828A)

(622 x 807mm)

2

Right Side (D1012A)

(904 x 390mm)

3

8

76

5

9

10

4

Rail (D1009A)

(596 x 103mm) x 3

Drawer Back (W564 - 124)

(564 x 124mm) x 5

Drawer Base (T575 - 367)

(575 x 367mm) x 5

Left Drawer Side (W370-124LH)

(370 x 124mm) x 5

Right Drawer Side (W370-124RH)

(370 x 124mm) x 5

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 10

B

Metal dowel (F901) x 20

D E

Large locking nut (F900) x 10

F

G H I

K

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Small locking nut (F3) x 10

C

Nail (F51) x 16

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J

Drawer runner (F1004) x 10 Handle (F930) x 5

25mm Screw (F50) x 10 9mm Screw (F74) x 10 9mm Screw (F73) x 20

L M

13mm Screw (F79) x 1

Bracket (F327) x 1

Knock-in Peg (F171) x 20

O

Plastic Nail (F91) x 4

N

Wedgefix (F639) x 20

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 5

Prepare the drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten the metal dowels up fully against the panels.

B

5

B

5

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

E

6

7

Step 2

x 5 x 5

E

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

E

6

7

Step 3

x 5

B

E

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

6 7

5

E

6 7

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

7

6

5

Assembly Instructions

5

Step 4

Attach the handle

Attach a handle to each drawer front using 2 screws .

K

G

Step 6

5

x 5

G

K

5

F

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front . .

Step 5

Fit the drawer back

Fit the drawer back . between the drawer sides and .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

9

6 7

5

8

6 7

9

8

F

x 5

F

6

9

7

6

6 7

8

N

Fit the wedgefixes

Turn the large drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

N

Step 7

7

Profiled

front edge

Profiled

front edge

Assembly Instructions

6

Step 8

Profiled

front edge

I

J

I

J

I

J

I

J

I

J

Profiled

front edge

I

Prepare the left side

a: Place 5 runners on

the left side . Slide back the top of the runner and use the 1st hole from the front to fit the 1st screw .

b: Slide the runner back

the other way and fit the 2nd screw into the corresponding hole in the left side .

Tap 2 plastic nails into the bottom edge of the side . .

c: Screw 5 metal

dowels into the left side .

a:

b:

c:

1

I

B

1

I

J

I

J

I

J

I

II

I

1

B

O

1

O

1

Assembly Instructions

7

Step 9

I

J

I

J

I

J

Profiled

front edge

I

J

I

Profiled

front edge

Profiled

front edge

I

J

I

J

I

J

I

J

I

Profiled

front edge

B

O

2

Prepare the right side

a: Place 5 runners on

the right side . Slide back the top of the runner and use the 1st hole from the front to fit the 1st screw .

b: Slide the runner back

the other way and fit the 2nd screw into the corresponding hole in the right side .

Tap 2 plastic nails into the bottom edge of the side . .

c: Screw 5 metal

dowels into the right side .

I

J

2

I

B

2

O

2

a:

b:

c: