Argos ZCP44D2-BD-AR, ZCP44D2-W-AR, ZCP44D2-WO-AR, ZCP44D2-KP-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width -123.5cm

Depth - 39cm

Height - 74.4cm

Capella - 4 + 4 Drawer Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 6 - 28/03/14

Important - Please read these instructions fully before starting assembly

249/6674

247/6058

268/2433

246/7081

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 41kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D1039A)

(744 x 390mm)

Left Hand Drawer Front (D1044A)

(599 x 157mm) x 4

Back (X832A)

(1229 x 646mm)

Rail (D1043A)

(1205 x 103mm) x 2

Right Side (D1040A)

(744 x 390mm)

Right Hand Drawer Front (D1045A)

(599 x 157mm) x 4

Upright (D1041A)

(621 x 368mm)

Support (D1046A)

(300 x 85mm)

Top (D1042A)

(1205 x 369mm)

Drawer Back (W564 - 124)

(564 x 124mm) x 8

Drawer Base (T575 - 367)

(575 x 367mm) x 8

Left Drawer Side (W370-124LH)

(370 x 124mm) x 8

Right Drawer Side (W370-124RH)

(370 x 124mm) x 8

Please check you have all the fittings listed below

Tools required

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 8

Metal dowel (F901) x 26

D E

Large locking nut (F900) x 10

G H I

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Small locking nut (F3) x 16

Nail (F51) x 22

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Drawer runner (F1004) x 16

Handle (F930) x 8

25mm Screw (F50) x 16 9mm Screw (F74) x 16 9mm Screw (F73) x 32

45mm Screw (F65) x 3

Knock-in Peg (F171GY) x 32

Plastic Nail (F91) x 5

Wedgefix (F639) x 32

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 4

Prepare the 4 left hand drawer fronts and 4 right hand drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front and .

Note: Tighten the metal dowels up fully against the panels.

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 2

x 8 x 8

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Step 3

x 8

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts and .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

6 7

Note: The right drawer front has a shallow identification mark.

+ 11 hidden pages