Argos ZCP440-KP-AR ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width -123.5cm
Depth - 39cm
Height - 74.4cm
Capella - 4 + 4 Drawer Chest
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 5 - 16/05/12
Important - Please read these instructions fully before starting assembly
615/8602
615/8585
615/8592
615/5571
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 38kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
5
2
98
6
10
12
Left Side (D1039A)
(744 x 390mm)
Left Hand Drawer Front (D1044A)
(599 x 157mm) x 4
Back (X832A)
(1229 x 646mm)
Rail (D1043A)
(1205 x 103mm) x 2
Right Side (D1040A)
(744 x 390mm)
Drawer Base (T440)
(317 x 575mm) x 8
Right Hand Drawer Front (D1045A)
(599 x 157mm) x 4
Upright (D1041A)
(621 x 368mm)
Support (D1046A)
(300 x 85mm)
7
13
4
11
Left Drawer Side (W516BLH)
(320 x 95mm) x 8
Right Drawer Side (W516BRH)
(320 x 95mm) x 8
Drawer Back (W440BBK)
(564 x 95mm) x 8
3
Top (D1042A)
(1205 x 369mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 26
D E
Large locking nut (F900) x 10
F
G H I
K
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Small locking nut (F3) x 16
C
Nail (F51) x 22
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Drawer runner (F1004) x 16
Handle (F930) x 8
25mm Screw (F50) x 16 9mm Screw (F74) x 16 9mm Screw (F73) x 32
45mm Screw (F65) x 3
L
Knock-in Peg (F171) x 32
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 8
x 4
x 4
x 8
Prepare the 4 left hand drawer fronts and 4 right hand drawer fronts
Screw 2 metal dowels into the holes shown on the back of each drawer front and .
Note: Tighten the metal dowels up fully against the panels.
B
6
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
B
E
9
10
E
Step 2
Step 3
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
7
x 8
8
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
E
10
E
9
Assemble the drawer sides and back
Fit the left drawer side and right drawer side to the drawer back by tapping in 4 knock-in pegs .
9
10
8
9
L
L
L
L
L
10
Small groove
B
B
6
7
B
B
Left hand
drawer front has
holes nearest
this edge
Right hand
drawer front has
holes nearest
this edge
Assembly Instructions
5
Step 4
Attach the handle
Attach a handle to each drawer front and using 2 screws . .
K
G
Step 6
6
x 8
G
G
K
Step 5
x 8
Fit the drawer base
Slide the drawer base along the grooves of the drawer sides and into the groove of the drawer back .
11
9 10
8
Attach the drawer front
Turn the drawer assembly over and push onto the back of the drawer front and .
Note: Turn locking nuts clockwise to secure panels - more than 1/2 a turn.
6
E
B
B
E
x 8
Note: The locking nuts can be on either surface of the drawer sides.
11
7
7
9
10
8
9
10
6 7
and
6 7
and
Profiled
front edge
Profiled
front edge
Profiled
front edge
Assembly Instructions
6
Step 7
Profiled
front edge
I
J
I
J
Back edge
I
J
Prepare the left side
a: Place 4 runners on
the left side . Slide back the top of the runner and use the 1st hole from the front to fit the 1st screw .
b: Slide the runner back
the other way and use the 3rd hole from the back to fit the 2nd screw .
c: Screw 4 metal
dowels into the left side .
a:
b:
c:
1
I
B
1
I
J
I
J
I
J
I
J
1
1
1
I
I
I
I
B
B
B
B
Assembly Instructions
7
Step 8
Prepare the right side
a: Place 4 runners on
the right side . Slide back the top of the runner and use the 1st hole from the front to fit the 1st screw .
b: Slide the runner back
the other way and use the 3rd hole from the back to fit the 2nd screw . .
c: Screw 4 metal
dowels into the right side .
Profiled
front edge
I
J
Back edge
I
J
I
J
2
I
B
2
a:
b:
c:
2
2
2
I
J
I
J
I
J
I
J
I
I
I
I
B
B
B
B
Profiled
front edge
Profiled
front edge
Profiled
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 9
Prepare the upright
a: Place 4 runners on
the upright . Slide back the top of the runner and use the 1st hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the upright .
Insert 2 large locking nuts as shown.
Note: Arrow on locking nut must point towards hole in edge of panel.
Turn the upright over.
c: Repeat the
instructions above to fit 4 runners onto the other side of the upright using screws .
I
J
4
I
D
I
J
13
Turn the upright over
4
a:
b:
c:
I
J
I
J
I
J
I
J
Finished
front edge
I
I
I
I
Finished
front edge
D
4
4
Profiled
front edge
I
J
I
J
I
I
J
I
J
I
J
4
4
D
D
J
I
I
I
I
A
A
Assembly Instructions
9
Prepare the top
Tap 4 wooden dowels into the top as shown.
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 4 large locking nuts into the top .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Screw 2 metal dowels into the top .
10mm
A
A
3
3
D
D
B
Join the upright and top
Push the top onto the upright as shown.
Use a screwdriver to tighten the 2 large locking nuts fitted to the upright .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Step 11
3
4
D
D
4
B
3
D
D
D
D
A
A
Finished
front edge
3
B
B
plain chipboard surface
3
Finished
front edge
Finished
front edge
4
Step 10
Loading...
+ 21 hidden pages