Argos ZCP33R2-WO-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 115cm

Depth - 49cm

Height - 181cm

Capella - 3 Drawer 3 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 5 - 23/04/14

Important - Please read these instructions fully before starting assembly

255/7276

239/2682

257/9838

258/4517

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 77kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Tools required

Rule

Scissors

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Step ladder

Electric drill (only use when drilling into walls)

Square

mm

10

20

30

40

50

60

70

80

90

100

mm

10

20

30

40

50

60

70

80

90

100

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D1013A)

(1808 x 490mm)

2 3

6

Right Side (D1014A)

(1808 x 490mm)

Top/Base (D1018A)

(1119 x 471mm) x 2

Drawer Front (D1022A)

(369 x 157mm) x 3

Plinth (D1024A)

(1119 x 85mm)

Short Divider (D1019A)

(483 x 470mm)

Fixed Shelf (D1020A)

(346 x 469mm)

10

7

11

Outer Door (D1017A)

(1701 x 369mm) x 2

Long Divider (D1084A)

(1685 x 470mm)

8

4

5

Centre Door (D1025A)

(1221 x 369mm)

9

13

15

12

Drawer Base (T325-367)

(325 x 367mm) x 3

14

18

17

Small Back (X831A)

(1711 x 392mm)

Large Back (X830A)

(1711 x 753mm)

Hanging Rail (FHR723)

(723mm long)

16

Loose Shelf (D1023A)

(369.5 x 469mm) x 3

Drawer Back

(W314-124)

(314 x 124mm) x 3

Left Drawer Side

(W370-124LH)

(370 x 124mm) x 3

Right Drawer Side (W370-124RH)

(370 x 124mm) x 3

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 10

B

Metal dowel (F901) x 16

C

D E

Large locking nut (F900) x 10

F

G H I

Nail (F51) x 34

N

Rail holder

(F1014) x 2

25mm Screw (F50) x 12 13mm Screw (F79) x 11

J

13mm Screw (F63) x 18

Q

Drawer runner (F1004) x 6

K

9mm Screw (F74) x 6

L

9mm Screw (F73) x 12

M

Shelf stud (F110) x 12

P

Handle (F930) x 6

Small locking nut (F3) x 6

Bracket (F327) x 1

O

S

40mm Screw (F910) x 10

R

Hinge (F518) x 3

Hinge plate (F523) x 3

Knock-in Peg (F171) x 12

AHP1546

AHP1043

U

Hinge (F522) x 6

T

Hinge plate (F523) x 6

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Ruler - Use this ruler to help correctly identify the screws

W

Plastic Nail

(F91) x 5

Wedgefix

(F639) x 6

V

X

Y

Nail screw

(F277) x 6

Back holder (F276) x 6

* These can also be round

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 3

x 3 x 3

Prepare the drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten the metal dowels up fully against the panels.

B

8

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

B

E

11

12

Step 2

B

8

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

E

B

E

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

E

11

12

11

8

Small groove

Step 3

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the 3 drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

11 12

8

E

11 12

x 3

Assembly Instructions

5

Step 4

Attach the handle

Attach a handle to each drawer front using 2 screws .

P

H

Step 6

8

x 3

H

P

Step 5

8

6

7

8

F

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the small drawer front .

Fit the drawer back

Fit the drawer back . between the drawer sides and .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

15

11 12

8

14

11 12

15

14

F

x 3

F

15

12

11

11 12

14

12

11

15

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

V

x 3

8

H

Assembly Instructions

Step 8

3

R

Finished

front edge

L

Q

J

Back edge

L

Q

Prepare the long divider

a: Place 3 runners on

the long divider . Slide back the top of the runner and use the 1st hole from the front to fit the 1st screw .

b: Slide the runner back

the other way and use the 3rd hole from the back to fit the 2nd screw . .

c: Important: The hinge

plates used in this step are in the bag marked as AHP1043.

Fit 3 hinge plates onto the long divider , making sure that the slot is facing towards the finished front edge.

Push a rail holder into the long divider . Make sure that it is fitted straight, in line with the panel edges.

L

Q

3

L

a:

b:

c:

R

3

N

L

Q

L

Q

L

Q

Finished

front edge

3

LL

L

3

Finished

front edge

Finished

front edge

R

N

3

AHP1043

AHP1546

6

Finished

front edge

Finished

front edge

3

Assembly Instructions

7

Step 9

Step 10

Prepare the top and base

Tap 4 wooden dowels into the top and base . as shown.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Insert 4 large locking nuts into the top and base as shown.

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

D

A

10mm

A

4

D

Finished

front edge

x 2

D

G

Join the long divider and fixed shelf

Attach the fixed shelf to the long divider using 2 screws .

G

7

3

7

Important: If one of the top/base panels has a plain chipboard surface this must be used as the base.

G

Assembly Instructions

8

Step 11

Profiled

front edge

Step 12

Prepare the right side

Important: The hinge plates used in this step are in the bag marked as AHP1546.

Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

Screw 5 metal dowels into the right side .

Note: Tighten the metal dowels up fully against the panels.

T

2

B

2

T

B

2

Finished

front edge

Finished

front edge

Finished

front edge

G

4

Fit top and base to the long divider

Attach the top to the long divider using 2 screws .

Attach the base to the long divider using 2 screws .

G

4

3

4

3

G

4

3

G

Important: If one of the top/base panels has a plain chipboard surface this must be used as the base.

AHP1546

AHP1043

Finished

front edge

Finished

top edge

Finished

top edge

Finished

front edge

Assembly Instructions

9

Step 13

Step 14

Profiled

front edge

of right side

Fit the right side

Push the right side onto the top and base as shown.

Use a screwdriver to tighten the 4 large locking nuts fitted to the top and base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

D

B

4

2

4

4 4

D

Finished

front edge

L

Q

Back edge

L

Q

L

Fit runners to short divider

a: Place 3 runners on

the short divider . Slide back top of runner and use 1st hole from the front to fit 1st screw . .

b: Slide runner back the

other way and use 3rd hole from the back to fit 2nd screw .

Q

6

L

a:

b:

L

Q

L

Q

L

Q

4

Finished

top edge

Finished

front edge

Assembly Instructions

10

Step 15

Step 16

Profiled

front edge

1

T

Prepare the left side

Important: The hinge plates used in this step are in the bag marked as AHP1546.

Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

Screw 5 metal dowels into the left side .

Note: Tighten the metal dowels up fully against the panels.

Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges.

B

N

B

T

1

B

1

N

1

Fit the short divider

Attach the short divider . to the base using 2 screws .

Attach the short divider . to the fixed shelf using 2 screws .

G

6

6 7

4

G

AHP1546

AHP1043

4

7

Assembly Instructions

11

Step 17

Step 18

Fit the plinth

Push the plinth onto the right side .

Use a screwdriver to tighten the large locking nut fitted to the plinth .

Step 19

Finished

front edge

Fit the left side

Push the left side onto the top , base and plinth .

Use a screwdriver to tighten the 5 large locking nuts fitted to the top , base and plinth .

2

4

1

4 4

5

4 4

5

D

Prepare the plinth

Tap 2 wooden dowels into the plinth .

Insert 2 large locking nuts into the plinth . .

D

A

D

5

A

5

D

2

5

2

D

5

Note: Support the plinth until the left side has been fitted in the next step.

Plain chipboard

surface

4