Argos ZCP2BS2-BD-ARDO, ZCP2BS2-KP-ARDO, ZCP2BS2-W-ARDO, ZCP2BS2-WO-ARDO, Capella - 2 Drawer Bedside ASSEMBLY INSTRUCTIONS
MADE IN
BRITAIN
Dimensions
Width - 38cm
Depth - 39cm
Height - 42.4cm
Capella - 2 Drawer Bedside
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 6 - 26/03/14
Important - Please read these instructions fully before starting assembly
244/7173
259/7456
259/1720
247/9419
258/3721
258/2997
237/8998
238/4023
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 10kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (D0999A)
(424 x 390mm)
Top (D1001A)
(349 x 369mm)
Drawer Front (D1003A)
(345 x 157mm) x 2
Back (X826A)
(375 x 325mm)
Rail (D1002A)
(349 x 103mm) x 2
Right Side (D1000A)
(424 x 390mm)
Drawer Base (T328-367)
(328 x 367mm) x 2
1 2 3
4
5
9 10
86 7
Drawer Back (W317-124)
(317 x 124mm) x 2
Left Drawer Side (W370-124LH)
(370 x 124mm) x 2
Right Drawer Side (W370-124RH)
(370 x 124mm) x 2
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 12
D E
Large locking
nut (F900) x 8
G H I
K
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Small locking
nut (F3) x 4
C
Nail (F51) x 10
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Drawer runner (F1004) x 4 Handle (F930) x 2
25mm Screw (F50) x 4 9mm Screw (F74) x 4 9mm Screw (F73) x 8
F
Knock-in Peg (F171) x 8
M
Plastic Nail (F91) x 4
L
Wedgefix (F639) x 4
Loading...