Argos ZCP2BS2-BO-ARS ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020

Important - Please read these instructions fully before starting assembly

Dimensions

Width - 38cm

Depth - 39cm

Height - 58.5cm

Capella - 3 Drawer Bedside

Assembly Instructions - Please keep for future reference

Issue 2 - 18/09/15

395/8056

408/6192

448/1780

424/5263

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 13kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).

• Dispose of all packaging
carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020

Please check you have all the panels listed below

When applicable, remove any
protective film before use

2

1

4

2 3

8

5

9

10

6 7

Left Drawer Side (W370-124LH)

(370 x 124mm) x 3

Right Drawer Side (W370-124RH)

(370 x 124mm) x 3

Top (D1001A)

(349 x 370mm)

Drawer Front (D1003A)

(345 x 157mm) x 3

Back (X490-375)

(490 x 375mm)

Rail (D1002A)

(349 x 103mm) x 2

Drawer Base (T328-367)

(328 x 367mm) x 3

Drawer Back (W317-124)

(317 x 124mm) x 3

Left Side (D1006A)

(584 x 390mm)

Right Side (D1007A)

(584 x 390mm)

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

Components - Fittings

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020

Tools required

3

A

Wooden dowel (F22) x 8

B

Metal dowel (F901) x 14

D E

Large locking
nut (F900) x 8

G H I

K

Rule Scissors Hammer

Eye protection
(when using a
hammer or drill)

Cross-head
screwdriver

Small locking
nut (F3) x 6

C

Nail (F51) x 12

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J

Drawer runner (F1004) x 6 Handle (F930) x 3

25mm Screw (F50) x 6 9mm Screw (F74) x 6 9mm Screw (F73) x 12

F

Knock-in Peg (F171) x 12

M

Plastic Nail (F91) x 4

L

Wedgefix (F639) x 6

5

Assembly Instructions

4

Step 1

x 3

x 3

x 3

x 3

B

B

E

E

E

E

6

7

Step 2

Prepare the 3 drawer
fronts

Screw 2 metal dowels
into each of the drawer
fronts .

Note: Tighten the metal
dowels up fully against
the panels.

B

5

Prepare the drawer
sides

Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

Step 3

E

6

7

Attach the drawer
sides to the drawer
fronts

Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .

Turn the small locking
nuts on the left
drawer side and right
drawer side .

Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.

6
7

5

E

E

6
7

6

7

B

B

5

5

Assembly Instructions

5

Step 4

F

F

Fit the drawer base

Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .

Step 5

Fit the drawer back

Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .

Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .

Step 6

9

6 7

5

8

6 7

9

8

8

F

Attach the handles

Attach a handle to
each of the drawer fronts
. using screw .

Note: Do not
overtighten the screw.

K

G

5

6 7

Step 7

Fit the wedgefixes

Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.

L

x 3

x 3

x 3

F

F

x 3

L

L

L

9

6

8

6

7

9

7

K

G

G

5

Profiled

front edge

Profiled

front edge

Profiled

front edge

Assembly Instructions

6

Step 8

Profiled

front edge

I

J

I

J

Prepare the left side

a: Place 3 runners on

the left side . Slide
back the top of the
runner and use the 1st
hole from the front to fit
the 1st screw .

b: Slide the runner back

the other way and fit the
2nd screw into the
corresponding hole in
the left side .

c: Screw 4 metal

dowels into the left
side .

a:

b:

c:

1

I

B

1

1

1

1

1

B

B

B

B

I

J

I

I

I

I

J

I

J

Assembly Instructions

7

Step 9

Prepare the right side

a: Place 3 runners on

the right side . Slide
back the top of the
runner and use the 1st
hole from the front to fit
the 1st screw .

b: Slide the runner back

the other way and fit the
2nd screw into the
corresponding hole in
the right side .

c: Screw 4 metal

dowels into the right
side .

Profiled

front edge

I

J

I

J

2

I

B

2

2

a:

b:

c:

I

J

I

I

I

I

J

I

J

Profiled

front edge

Profiled

front edge

Profiled

front edge

B

B

B

B

2

2

2

A

Finished

front edge

Finished

front edge

A

A

Assembly Instructions

8

Step 10

Prepare the top

Tap 4 wooden dowels
into the top as
shown.

Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.

Insert 4 large locking
nuts into the top
as shown.

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

D

10mm

A

A

3

3

D

Fit the top to the right
side

Push the top onto
the right side as
shown.

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

Step 11

3

2

D

D

D

D

D

D

A

A

Finished

front edge

3

B

D

3

2

Prepare the 2 rails

Tap 2 wooden dowels
into each of the rails .

Insert 2 large locking
nuts into each of the
rails .

A

4

4

x 2

Step 12

D

D

A

D

4

Assembly Instructions

9

Step 13

Fit the 2 rails

Push the rails onto
the right side as
shown.

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the rails .

4

2

D

4

Support this rail until
the left side has been
fitted in the next step.

Fit the left side

Push the left side
onto the assembly.

Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the top and the rails
.

D

1

3

4

Step 14

4

2

4

4

4

1

3

Fit the 4 plastic nails

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .

M

1

2

M

M

M

M

Step 15

1

2

Assembly Instructions

10

Step 16

Step 17

b:

C

Fit the back

a: Square up the unit by

making sure that
measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the
outside edges of the
back .

Note: Nails should be
spaced about 150mm
apart.

Stand the unit up for
the next step.

10

C

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

10

yy

yy

xx

10

xx

Fit the drawers

Starting with the bottom
drawer, slide both the
runners forward and
locate the drawer
sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .

Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.

Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.

H

J

J

H

2nd threaded

hole

J

H

6 7

H

H

6

7

Assembly Instructions

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020

11

ALR3161

Step 18

Assembly is complete