Argos ZCP24MR2-WO-AR ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 152cm
Depth - 49cm
Height - 181cm
Capella - 2 Drawer 4 Door Robe
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 6 - 23/04/14
Important - Please read these instructions fully before starting assembly
266/0709
266/9683
241/5844
248/4112
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 96kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Tools required
Rule
Scissors
Spirit level
Hammer Bradawl
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Step ladder
Electric drill (only use when drilling into walls)
Square
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (D1013A)
(1808 x 490mm)
2 3
7
Right Side (D1014A)
(1808 x 490mm)
11
8
12
Large Door (D1017A)
(1701 x 369mm) x 2
9
4
6
10
15
13
14
17
Large Back (X830A)
(1711 x 753mm) x 2
Hanging Rail (FHR728)
(728mm long) x 2
16
Mirror Door (D1030A)
(1381 x 369mm) x 2
(Mirror - SG14 1376 x 311mm 4mm Safety Back SAR)
Short Divider
(D1027A)
(323 x 470mm) x 2
Centre Divider (D1028A)
(1369 x 470mm)
Plinth (D1032A)
(1491 x 85mm)
Top (D1026A)
(1491 x 471mm)
5
Drawer Front (D1031A)
(743 x 157mm) x 2
Drawer Back
(W688-124BK)
(688 x 124mm) x 2
Drawer Base (T699-367)
(699 x 367mm) x 2
Fixed Shelf (D1029C)
(720 x 470mm)
Drawer Support
(D1397A)
(302 x 302mm)
18
Left Drawer Side
(W370-124LH)
(370 x 124mm) x 2
Right Drawer Side
(W370-124RH)
(370 x 124mm) x 2
Base (D1111C)
(1491 x 471mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 16
C
D E
Large locking nut (F900) x 12
F
G H I
Nail (F51) x 48
N
Rail holder
(F1014) x 4
25mm Screw (F50) x 12 13mm Screw (F79) x 1
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
J
13mm Screw (F63) x 24
Drawer runner (F1004) x 4
K
9mm Screw (F74) x 4
M
P
Handle (F930) x 6
T
Small locking nut (F3) x 4
Bracket (F327) x 1
O
R
Hinge (F522) x 6
S
Hinge plate (F523) x 6
40mm Screw (F910) x 14
Q
Hinge Plate (F521) x 6
Hinge (F520) x 6
L
9mm Screw (F73) x 8
AHP1546
AHP0826
Knock-in Peg (F171GY) x 8
V
Plastic Nail
(F91) x 5
Wedgefix
(F639) x 8
U
W
X
Nail screw
(F277) x 6
Back holder (F276) x 6
* These can also be round
9
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 2
Prepare the drawer fronts
Screw 2 metal dowels into the holes shown on the back of each drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
9
B
Step 3
B
B
9
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
E
12
13
Step 2
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
E
x 2
E
E
12
13
x 2
x 2
B
E
Attach the drawer sides to the drawer fronts
Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
12 13
9
E
E
12 13
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
13
12
F
F
9
Assembly Instructions
5
Attach the handle
Attach a handle to each drawer front using 2 screws .
M
H
Step 6
9
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front . .
Step 5
Fit the drawer back
Fit the drawer back . between the drawer sides and .
Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
15
12 13
9
14
12 13
15
14
14
F
x 2
x 2
12 13
Fit the wedgefixes
Turn the 2 drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
U
Step 7
Step 4
F
F
U
15
12
13
14
12
13
15
x 2
x 2
H
H
M
U
U
U
U
9
Finished
top edge
Finished
top edge
Finished
top edge
Finished
front edge
Finished
top edge
Assembly Instructions
6
Step 8
Finished
front edge
Finished
front edge
L
P
Prepare a short divider
a: Place 2 runners on
a short divider . Slide back top of runner and use 1st hole from the front to fit 1st screw .
b: Slide runner back the
other way and use 3rd hole from the back to fit 2nd screw .
P
7
L
L
Prepare the other short divider
a: Place 2 runners on
a short divider . Slide back top of runner and use 1st hole from the front to fit 1st screw .
b: Slide runner back the
other way and use 3rd hole from the back to fit 2nd screw .
P
7
L
L
a:
L
P
L
P
Back edge
L
P
b:
a:
b:
L
P
L
P
Finished
front edge
L
P
Finished
front edge
L
L
Back edge
L
P
Finished
front edge
Step 9
7
7
7
7
L
L
Assembly Instructions
7
Step 10
Step 11
Prepare the fixed shelf
Screw 2 metal dowels into the fixed shelf .
B
B
8
Finished
front edge
B
8
G
G
Finished
front edge
Finished
front edge
Finished
front edge
8
Join the short dividers to the fixed shelf
Attach the 2 short dividers to the fixed shelf using 4 screws . .
7
8
G
7
G
G
7
Assembly Instructions
Step 12
Step 13
8
Finished
front edge
Q
Prepare the centre divider
Important: The hinge plates used in this step are in the bag marked as AHP0826.
Fit 3 hinge plates to the centre divider as shown, making sure that the slot is facing towards the finished front edge.
Push a rail holder into the centre divider . Make sure that it is fitted straight, in line with the panel edges.
Turn the centre divider over
Fit 3 hinge plates to the other surface of the centre divider as shown, making sure that the slot is facing towards the finished front edge.
Push another rail holder . into the centre divider . .
Q
Q
Q
Q
Q
Q
Q
Finished
front edge
Q
Q
3
3
3
3
Q
3
Turn the centre
divider over
AHP1546
AHP0826
N
N
N
3
N
Finished
front edge
8
3
Fit the centre divider
Attach the centre divider . to the fixed shelf using 2 screws .
G
G
3 8
G
A
A
b:
Assembly Instructions
9
Step 14
Step 15
Prepare the drawer support
Insert 2 large locking nuts into the drawer support .
D
D
18
Note: Due to the manufacturing process, the drawer support may either have 1 or 2 plain chipboard surfaces.
D
18
A
A
D
A
A
Finished
front edge
D
D
D
Prepare the top and base
a: Tap 4 wooden dowels
. into the top .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 4 large locking nuts into the top .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
b: Tap 4 wooden
dowels into the base . .
Insert 4 large locking nuts into the base
A
4
4
5
D
4
D
A
A
Finished
front edge
D
D
D
5
plain chipboard surface
a:
A
5
D
.
D
Plain
chipboard
surface
Assembly Instructions
Step 16
10
Step 17
Finished
front edge
7
7
G
G
G
G
5
Fit the base
Attach the base to the short dividers and drawer support using 6 screws .
5
7
G
G
G
18
18
8
18
Fit the drawer support
Push the drawer support . onto the metal dowels fitted to the fixed shelf .
Use a screwdriver to tighten the 2 large locking nuts fitted to the drawer support .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
B
D
18
8
B
D
18
D
Note: Support the shelf support until the base has been fitted in the next step.
plain
chipboard
surface
Assembly Instructions
11
Step 18
Step 19
G
Finished
front edge
G
4
Large locking nuts
on this surface
Fit the top
Attach the top to the centre divider using 2 screws .
4
3
G
3
Profiled
front edge
1
S
S
S
S
Prepare the left side
Important: The hinge plates used in these 2 steps are in the bag marked as AHP1546.
Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.
Screw 5 metal dowels into the left side .
Note: Tighten the metal dowels up fully against the panels.
Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges.
B
B
B
B
B
B
N
B
B
S
S
1
1
B
1
N
1
AHP1546
AHP0826
Assembly Instructions
Step 20
Step 21
12
4
2
Fit the right side
Push the right side onto the top and base as shown.
Use a screwdriver to tighten the 4 large locking nuts fitted to the top and base .
2
4
5
D
4 5
Profiled
front edge
Prepare the right side
Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
Screw 5 metal dowels into the right side .
Note: Tighten the metal dowels up fully against the panels.
Push a rail holder into the right side . Make sure that it is fitted straight, in line with the panel edges.
S
2
B
2
N
2
2
S
S
S
S
B
B
B
B
B
N
2
2
4
4
5
Assembly Instructions
13
Step 22
6
Note: Support the plinth until the left side has been fitted in the next step.
Fit the plinth
Push the plinth onto the right side as shown.
Use a screwdriver to tighten the large locking nut fitted to the plinth . .
6
2
D
6
2
Plain chipboard
surface
A
A
D
D
A
Prepare the plinth
Tap 2 wooden dowels into the plinth .
Insert 2 large locking nuts into the plinth
6
6
6
D
.
Plain chipboard
surface
Step 23
Assembly Instructions
Step 24
14
4
6
5
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 5 large locking nuts fitted to the top , base and plinth .
1
D
4 5
6
1
2
Fit the 5 plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . and 1 into the plinth . .
V
1
2
6
6
1
2
V
V
V
V
V
Step 25
Assembly Instructions
15
Step 26
Fit the back panels
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the 2 backs
coloured surface facing down, onto the unit as shown.
Make sure that the 2 backs are pushed up tight against each other and that they meet in the centre of the centre divider’s back edge.
Nail around the outside edges of the 2 backs .
Note: Do not nail where the 2 backs meet. Nails should be spaced out evenly.
c: Push the 6 nail
screws through the 6 back holders and tap them down between the 2 backs and into the back edge of the centre divider .
Keep tapping the nail screws in until the back holders dig into the small and large back.
C
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
y
x
y
y
x
b:
C
17
17
3
17
Warning: The unit is heavy. Lift with care.
17
17
W
X
17
17
X
XW
+
c:
W
X
17
3
W
X
Stand the unit up for the next step.
Note: These can also be round
Assembly Instructions
Step 27
16
K
K
Fit the hanging rails and drawers
Push the hanging rails into the rail holders fitted to the left side , right side and centre divider .
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides . and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the wrap and out into the 2nd threaded hole in the runner.
Note: Do not over­tighten the screws . If they catch on the runner you may need to loosen them slightly.
K
1
16
2
3
12 13
N
P
P
K
16
N
16
16
2
1
3
2nd threaded
hole
P
K
Assembly Instructions
17
Step 28
Prepare the large doors
Important: The 6 hinges used in this step are in the bag marked as AHP1546.
Push fit 3 hinges into each large door .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
90
T
T
T
J
J
T
J
J
T
J
J
11
11
J
x 2
x 2
Step 29
Prepare the mirror doors
Important: The 3 hinges used in this step are in the bag marked as AHP0826.
Push fit 3 hinges into each mirror door .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
R
90
R
R
J
J
J
10
R
J
J
R
J
J
AHP1546
AHP0826
AHP1546
AHP0826
10
Warning: Glass! Handle with care
Assembly Instructions
Step 30
18
IMPORTANT
Carefully choose the 2 holes you need to drill for each mirror door.
Only drill 1 set of handle holes in each mirror door.
Drill the handle holes in each mirror door
Important: Please follow these instructions carefully.
Lay the 2 mirror doors . down onto a smooth surface.
Check that the hinges and holes are in the same place as the diagrams.
Note: We recommend the use of a small piece of waste wood, placed behind the hole while drilling, to reduce the possibility of any breakout.
Using the pilot hole in the rear face of the door, drill through the hole indicated opposite, using a 2.5mm diameter drill.
Turn the door over and open out the 2.5mm hole that you have just drilled by drilling back through it with a 5mm drill.
DO NOT drill
these holes
ONLY drill these
2 holes in the
mirror door
Small piece of
waste wood
DO NOT drill
these holes
ONLY drill these
2 holes in the
mirror door
Small piece of
waste wood
x 1
x 1
10
10
10
This will be the
LEFT mirror door
This will be the
RIGHT mirror door
Warning: Glass! Handle with care
Warning: Glass! Handle with care
Assembly Instructions
19
Step 31
M
H
H
Fit the mirror doors and handles
Note: The easiest way to attach the mirror doors . is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a handle to
each mirror door using 2 screws .
R
R
R
Q
Q
Q
R
Q
M
H
10
10
e:
a: b:
c: d:
B
Q
R
A
Q
R
Q
Q
R
R
R
Q
B
10
10
Warning: Glass! Handle with care
Assembly Instructions
Step 32
20
Fit the large doors and handles
Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a handle to
each large door using 2 screws .
T
T
T
S
S
S
T
S
M
H
11
11
e:
H
H
M
11
11
a: b:
c: d:
S
T
S
S
B
S
T
T
T
A
T
S
B
Assembly Instructions
21
Step 33
b:
c:
d:
a:
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
A
A
B
C
This shows the hinge and plate that is
fitted to the outer doors.
The ones fitted to the centre doors are
adjusted in the same way.
Loading...
+ 50 hidden pages