Argos ZCP22SR-KP-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 120cm

Depth - 59.5cm

Height - 181cm

Capella - 2+2 Sliding Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 18/12/13

Important - Please read these instructions fully before starting assembly

170/9568

145/1782

161/9304

146/9482

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 79kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Top Drawer Front (D2716A)

(1165 x 185mm)

7

Bottom Drawer Front (D2718A)

(1165 x 244mm)

Top Drawer Back (W526-115)

(526 x 115mm) x 2

Bottom Left Drawer Side (W547LH)

(350 x 150mm) x 2

Bottom Drawer Back (W526-150)

(526 x 150mm) x 2

2

3

4 5

Bottom Right Drawer Side (W547RH)

(350 x 150mm) x 2

6

8 9

Drawer Base (T537-347)

(537 x 347mm) x 4

Top Left Drawer Side (W350-115LH)

(350 x 115mm) x 2

Top Right Drawer Side (W350-115RH)

(350 x 115mm) x 2

Components - Panels

Please check you have all the panels listed below

2

10

11 12

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D2710A)

(1808 x 592mm)

13

Right Side (D2711A)

(1808 x 592mm)

Top/Base (D2709A)

(1169 x 587mm) x 2

Large Divider (D2712A)

(1246 x 496mm)

Rail (D2714A)

(1169 x 85mm) x 2

Back Rail (D2715A)

(577 x 120mm) x 2

Door (D2717A)

(1237 x 592mm) x 2

15

14

Small Divider (D2713A)

(437.5 x 560mm)

16

17 19

Hanging Rail (FHR569)

(566mm long) x 2

18

Back (X1722-597)

(1722 x 597mm) x 2

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 16

C

D E F

G

40mm Screw (F910) x 4

13mm Screw (F63) x 38

Rail holder

(F1014) x 4

J

H

K

I

Top glide

(F956) x 4

Bottom glide

(F952) x 4

M N

Q

L

P

Bracket (F327) x 1

1167mm Track (F221) x 4

O

B

Metal dowel (F901) x 22

Large locking

nut (F900) x 22

Nail (F51) x 40

13mm Screw (F79) x 1

25mm Screw (F50) x 12

Buffer bracket

(F261) x 1

R

W X Y

Small locking nut (F3) x 8

Knock-in Peg (F171) x 16

Mushroom Head Pin (F260) x 4

S

T

R Runner (F160) x 4

b

L Runner (F161) x 4

T

c

L Runner (F159) x 4

T

a

R Runner (F162) x 4

T

d

350mm long

9mm Screw (F73) x 24

U

Double metal dowel (F566) x 2

Back holder (F276) x 5

V

Nail screw (F277) x 5

Wedgefix (F639) x 16

45mm Screw (F65) x 1

Handle (F930) x 6

4

3

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Step 2

Fit the top drawer sides to the top drawer backs

Make sure that the grooves on the inside of the drawer assembly line up.

a: With the top drawer

back in an upright position tap 2 knock-in pegs through the holes in the top left drawer side .

Turn the assemblies over

b: Hold the top drawer

back in position and tap 2 knock-in pegs through the holes in the top right drawer side .

Step 3

Fit the drawer bases

Slide the drawer base down the grooves in the top drawer sides and . and down into the groove in the top drawer back .

b:

a:

Turn the

assembly over

Prepare the 4 top drawer sides

Insert a small locking nut into the hole shown on each of the 2 top left drawer sides and 2 top right drawer sides .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

D

3

4

D

x 2

7

P

3

7

P

4

9

3

4

7

D

P

3

4

7

9

7

3

4

Assembly Instructions

5

Step 4

Fit the drawer front

Lower the 2 top drawer assemblies down onto the back of the top drawer front .

Use a screwdriver to tighten the 4 small locking nuts fitted to the drawer sides.

Note: Turn the small locking nuts as far as they will go - more than 1/2 a turn.

Step 5

B

Prepare the top drawer front

Screw 4 metal dowels into the top drawer front . .

Note: Tighten the metal dowels up fully against the panels.

B

1

D

B

1

D

B

1

Attach the handles

Attach 2 handles to the top drawer front using screws .

U

H

Step 6

1

U

1

H

Assembly Instructions

6

Step 7

Fit the runners and the wedgefixes

Turn the top drawer assembly over.

a: Fit a runner to

the bottom edge of the top left drawer side , as shown, making sure that it is pushed up against the back of the top drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit a runner to the bottom edge of the top right drawer side using the same method.

b: Repeat the

instructions above to fit the runners to the other top drawer sides.

c: Slide 2 wedgefixes

along each drawer base . and into the small groove on the back of the top drawer front . Slide 2 more wedgefixes . along each drawer base and into the small groove on the back of the top drawer back . .

Once in place, tighten up the screws.

4

T c

3

1

J

T d

a:

b:

c:

Runners must be

pushed up against

the drawer front

J

L

T c

L

T d

R

J

T c

T d

4

3

1

4

3

1

X

9

1

7

9

1

7

Assembly Instructions

7

Step 8

Step 9

Fit the bottom drawer sides to the bottom drawer backs

Make sure that the small grooves on the inside of the drawer assembly line up.

a: With the bottom

drawer back in an upright position tap 2 knock-in pegs through the holes in the bottom left drawer side . .

Turn the assemblies over

b: Hold the bottom

drawer back in position and tap 2 knock-in pegs through the holes in the bottom right drawer side . .

Step 10

Fit the drawer bases

Slide the drawer base down the grooves in the bottom drawer sides and . and down into the groove in the bottom drawer back .

b:

a:

Turn the

assembly over

Prepare the 4 bottom drawer sides

Insert a small locking nut into the hole shown on each of the 2 botom left drawer sides . and 2 bottom right drawer sides .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

D

5

6

D

x 2

x 2 x 2

8

P

5

8

P

6

9

5

6

8

D

5

6

P

5

6

8

9

5

6

8

Assembly Instructions

8

Step 11

Fit the drawer front

Lower the 2 bottom drawer assemblies down onto the back of the bottom drawer front .

Use a screwdriver to tighten the 4 small locking nuts fitted to the drawer sides.

Note: Turn the small locking nuts as far as they will go - more than 1/2 a turn.

Step 12

B

Prepare the bottom drawer front

Screw 4 metal dowels into the bottom drawer front .

B

2

D

B

2

D

B

Attach the handles

Attach 2 handles to the bottom drawer front . using screws .

U

H

Step 13

2

U

H

Assembly Instructions

9

Step 14

Fit the runners and the wedgefixes

Turn the bottom drawer assembly over.

a: Fit a runner to

the bottom edge of the bottom left drawer side , as shown, making sure that it is pushed up against the back of the bottom drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit a runner to the bottom edge of the bottom right drawer side . using the same method.

b: Repeat the

instructions above to fit the runners to the other bottom drawer sides.

c: Slide 2 wedgefixes

along each drawer base . and into the small groove on the back of the bottom drawer front . . Slide 2 more wedgefixes . along each drawer base and into the small groove on the back of the bottom drawer back .

Once in place, tighten up the screws.

6

T c

5

2

J

T d

a:

b:

Runners must be

pushed up against

the drawer front

J

L

T c

L

T d

R

J

T d

6

5

2

6

5

2

c:

X

9

X

9

2

8

X

8

2

Assembly Instructions

10

Step 15

A

O

Prepare the top and base

Place 2 plastic tracks down onto each of the top and base panels, making sure that they are flush with the edges of the panel.

Gently tap along the length of the plastic tracks until they are fitted flat to the surface of the panel.

Turn the top and the base panels over

Tap 4 wooden dowels into each of the top and base panels.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Insert 4 large locking nuts into each of the top and base panels.

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

10mm

A

13 13

O

13

O

4

Turn the top and

the base over

C

13 13

x 2

C

O

C

A

13

Finished

front edge

Finished

front edge

Assembly Instructions

11

Step 16

Finish preparing the base

Take 1 of the top/base panels you have just prepared and screw in 2 metal dowels .

This will now be used as the base.

Step 17

A

Finished

front edge

Prepare the large divider

Push a rail holder into the large divider . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .

Tap 4 wooden dowels into the large divider .

Turn the large divider over

Push a rail holder into the other surface of the large divider . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .

E

12

E

12

Turn the large divider over

J

E

J

E

J

Finished

front edge

A

12

13

Finished

front edge

B

13

x 1

Fit top and base to the divider

Attach the top and base to the large divider using 4 screws .

Finished

top edge

G

Assembly Instructions

12

Step 18

13

12

G

Step 19

Prepare the back rails

Insert 4 large locking nuts into each of the 2 back rails .

15

C

G

Note: The plastic

tracks must be on

the inside surfaces

of the top and base

Note: The base is

the one that has

the 2 metal dowels.

13

Top

13

12

Base

C

Plain chipboard

surface

x 2

15

Assembly Instructions

13

Step 20

E

J

T b

Finished front edge

J

Prepare the right side

a: Fit 2 runners to

the right side .

The 1st screw uses the 1st hole in from the front of the runner.

The 2nd and 3rd screws . use the holes that line up with the other panel holes.

Push a rail holder into the right side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .

b: Fit a screw into

the 2nd hole in at the top of the runner .

Screw 6 metal dowels into the right side .

K

T b

K

T b

11

K

J

T b

Finished front edge

1st screw

2nd screw

3rd screw

K K K

K

T b

K

B

J

B

11

E

11

J

a:

b:

11

Finished

front edge

Finished

front edge

15

Assembly Instructions

14

Step 21

12

Fit a back rail

a: Push a back rail

onto the large divider .

Tap 2 double metal dowels through the large divider and into the back rail until they ‘’bottom out’’.

b: Use a screwdriver to

tighten the 2 large locking nuts fitted to the back rail .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

15

12

S

Note: Support the back rail until the right side has been fitted in the next step.

a:

12

15

C

15

Step 22

Fit the right side

Push the right side onto the assembly.

Use a screwdriver to tighten the 4 large locking nuts fitted to the back rail , top and base .

11

C

15 13

13

S

C

S

C

S

b:

Finished

top edge

15

13

11

A

b:

Assembly Instructions

15

Step 23

a:

a:Qa:

Q

a:

13

11

Fit the mushroom head pins

a: Tap 2 mushroom

head pins into the holes on the outside of the right side and into the top and base .

b: Use a screwdriver to

tighten the 2 large locking nuts fitted to the top and base .

Q

11

13

C

13 13

Prepare the 2 rails

Tap 2 wooden dowels into each of the 2 rails . .

Insert 2 large locking nuts into each of the 2 rails .

A

14

C

Step 24

C

A

Plain chipboard

surface

14

x 2

14

Finished

front edge

Finished

front edge

Assembly Instructions

16

Step 25

T a

Finished front edge

J

T a

Finished front edge

1st screw

2nd screw

3rd screw

K K K

K

T a

K

T a

K

C

T b

Finished front edge

J

K

T b

K

T b

Finished front edge

1st screw

2nd screw

3rd screw

K K K

K

T b

K

J

Finished

front edge

Finished

front edge

Turn the small

divider over

Prepare the small divider

a: Fit 2 runners to

the small divider .

The 1st screw uses the 1st hole in from the front of the runner.

The 2nd and 3rd screws . use the holes that line up with the other panel holes.

b: Fit a screw into

the 2nd hole in at the top of the runner .

Insert 2 large locking nuts into the small divider .

Turn the small divider over

c: Fit 2 runners to

the small divider .

The 1st screw uses the 1st hole in from the front of the runner.

The 2nd and 3rd screws . use the holes that line up with the other panel holes.

d: Fit a screw into

the 2nd hole in at the top of the runner .

T a

16

K

J

T a

T b

16

K

J

T b

C

16

a:

b:

c:

d:

16