Argos ZAT4D-O-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 79.5cm

Depth - 41.5cm

Height - 86cm

Atlas - 4 Drawer Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 11/03/14

Important - Please read these instructions fully before starting assembly

181/6815

171/5129

146/7233

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 31kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

2

1

2

3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

4

5

Top (D2389A)

(793 x 396mm)

Large Drawer Front (D2394A)

(795 x 264mm)

Left Side (D2390A)

(845 x 395mm)

Right Side (D2391A)

(845 x 395mm)

Rail (D2392A)

(761 x 60mm) x 3

7

Small Drawer Front (D2393A)

(795 x 189mm) x 3

6

Small Left Drawer Side (W370-124LH)

(370 x 124mm) x 3

Small Right Drawer Side (W370-124RH)

(370 x 124mm) x 3

8

Large Left Drawer Side (W370-165LH)

(370 x 165mm)

Large Right Drawer Side (W370-165RH)

(370 x 165mm)

Small Wrap Back (W711-124)

(711 x 124mm) x 3

Large Wrap Back (W711-165)

(711 x 165mm)

Back (X836-787)

(836 x 787mm)

Drawer Base (T722-367)

(722 x 367mm) x 4

9

10 11 12

13

14

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 8

B

Metal dowel (F901) x 18

C

D E

Large locking nut (F900) x 10

F

G H I

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Small locking nut (F3) x 8

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

19mm Screw (F461) x 8

13mm Screw (F52) x 24

13mm Screw (F63) x 24 Nail (F51) x 22

Knock-in Peg (F171) x 16

J

R Runner (F160) x 4

b

L Runner (F161) x 4

J

c

L Runner (F159) x 4

J

a

R Runner (F162) x 4

J

d

350mm long

Handle (F227) x 4

K

623mm

M

L

Bracket (F327) x 1

13mm Screw (F79) x 1

N

Wedgefix (F639) x 16

O

Plastic Nail (F91) x 4

5

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

B

5

8

B

D

Step 2

Prepare the small drawer fronts

Screw 2 metal dowels into the holes shown on the back of each small drawer front .

Note: Tighten the metal dowels up fully against the panels.

B

5

Prepare the small drawer sides

Insert a small locking nut into the hole shown on each small left drawer side and small right drawer side . .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

D

7

8

Attach the drawer sides to the drawer fronts

Push the small left drawer sides and small right drawer sides . . onto the back of the small drawer fronts .

Turn the small locking nuts on the small left drawer sides and small right drawer sides . .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

8

7

8

5

D

7

8

Groove

7

D

B

5

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the groove is on the inside, as shown.

D

8

7

x 3

x 3 x 3

x 3

5

Step 4

I

Fit the drawer bases

Slide the drawer base down the grooves in the small drawer sides and and down into the groove in the small drawer fronts .

Step 5

Fit the small drawer backs

Fit the small drawer back . between the small drawer sides and .

Make sure that the drawer base fits into the groove in the small drawer back .

Hold the small drawer back in position and tap the knock-in pegs through the holes in the small drawer sides and .

Step 6

13

7

8

5

9

7 8

13

9

I

7

8

Attach the handles

Attach handles to the small drawer fronts using 2 screws .

K

E

5

8

I

13

7

8

9

7

8

13

E

K

5

x 3

Assembly Instructions

6

Step 7

Fit runners to the small drawers

Turn the small drawer assemblies over.

Fit runner , marked with ‘R’, to the bottom edge of the small right drawer side , as shown, making sure that it is pushed up against the back of the small drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit runner , marked ‘L’, to the bottom edge of the small left drawer side using the same method.

7

J d

8

5

G

J c

J d

Runners must be

pushed up against

the drawer front

R

G

L

J c

L

G

7

8

5

B

Prepare the large drawer front

Screw 2 metal dowels into the holes shown on the back of the large drawer front .

Note: Tighten the metal dowels up fully against the panels.

B

6

B

6

Step 9

Step 8

Fit the wedgefixes

Slide 2 wedgefixes into the small groove located on the back of the drawer front and 2 into the small groove in

the drawer back .

Once in place, tighten up the screws in the wedgefixes .

N

5

9

N

5

N

9

x 3

x 1

Fit the drawer base

Slide the drawer base down the grooves in the large drawer sides and and down into the groove in the large drawer front .

10

11

Assembly Instructions

7

Step 10

Step 12

Prepare the large drawer sides

Insert a small locking nut into the hole shown on the large left drawer side and large right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

D

10

11

D

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

D

6

11

B

D

Step 11

Attach the drawer sides to the drawer front

Push the large left drawer side . and large right drawer side . onto the back of the large drawer front .

Turn the small locking nuts on the large left drawer side and large right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

10

11

6

D

11

10

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the groove is on the inside, as shown.

6

Groove

10

11

13

10

11

6

11

10

13

I

Assembly Instructions

8

Step 13

Fit runners to the large drawer

Turn the large drawer assembly over.

Fit runner , marked with ‘R’, to the bottom edge of the large right drawer side , as shown, making sure that it is pushed up against the back of the large drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit runner , marked ‘L’, to the bottom edge of the large left drawer side using the same method.

10

J d

11

6

G

J c

J d

Runners must be

pushed up against

the drawer front

R

G

L

J c

L

G

10

11

6

11

10

13

12

Fit the large drawer back

Fit the large drawer back . between the large drawer sides and .

Make sure that the drawer base fits into the groove in the large drawer back .

Hold the large drawer back in position and tap the knock-in pegs through the holes in the large drawer sides and .

12

10 11

13

12

I

10

11

I

Step 14

Attach the handle

Attach a handle to the large drawer front using 2 screws .

Step 15

K

E

6

E

K

6

Assembly Instructions

9

Step 16

Step 17

Prepare the top

Screw 4 metal dowels into the top .

B

Plain chipboard

surface

3

B

3

Finished

front edge

6

Fit the wedgefixes

Slide 2 wedgefixes into the small groove located on the back of the drawer front and 2 into the small groove in

the drawer back .

Once in place, tighten up the screws in the wedgefixes .

N

6

12

N

12

Fix a bracket to the top .

The bracket must be flush against the back edge.

Secure the bracket using screw .

M

L

3

L

M