Argos ZAT2BS-O-AR, ZAT2BS-T-AR, ZAT2BS-W-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 47.5cm

Depth - 40cm

Height - 48cm

Atlas - Bedside

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 11/03/14

Important - Please read these instructions fully before starting assembly

145/3900

159/7206

166/2533

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 13.5kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).

• Dispose of all packaging
carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels

Please check you have all the panels listed below

2

1

2 3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

4 5

Top (D2379A)

(473 x 396mm)

Large Drawer Front (D2383A)

(475 x 264mm)

Left Side (D2380A)

(461 x 395mm)

Right Side (D2381A)

(461 x 395mm)

Rail (D2382A)

(441 x 60mm) x 2

7

Small Drawer Front (D2388A)

(475 x 189mm)

6

Small Left Drawer
Side (W370-124LH)

(370 x 124mm)

Small Right Drawer
Side (W370-124RH)

(370 x 124mm)

8

Large Left Drawer
Side (W370-165LH)

(370 x 165mm)

Large Right Drawer
Side (W370-165RH)

(370 x 165mm)

Small Wrap Back (W391-124)

(391 x 124mm)

Large Wrap Back (W391-165)

(391 x 165mm)

Back (X453-467)

(453 x 467mm)

Drawer Base (T402-367)

(402 x 367mm) x 2

9

10 11 12

13 14

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

A

Wooden dowel (F22) x 6

B

Metal dowel (F901) x 12

C

D E

Large locking
nut (F900) x 8

F

G H I

Rule Scissors Hammer

Eye protection
(when using a
hammer or drill)

Cross-head
screwdriver

Small locking
nut (F3) x 4

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

19mm Screw (F461) x 4

13mm Screw (F52) x 12

13mm Screw (F63) x 12 Nail (F51) x 13

Knock-in Peg (F171) x 8

J

R Runner (F160) x 2

b

L Runner (F161) x 2

J

c

L Runner (F159) x 2

J

a

R Runner (F162) x 2

J

d

350mm long

Handle (F266) x 2

K

304mm

L

Wedgefix (F639) x 8

M

Plastic Nail (F91) x 4

5

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

B

B

B

D

Step 2

Prepare the small
drawer front

Screw 2 metal dowels
into the holes shown on
the back of the small
drawer front .

Note: Tighten the metal
dowels up fully against
the panels.

B

5

Prepare the small
drawer sides

Insert a small locking
nut into the hole
shown on the small left
drawer side and
small right drawer side
. .

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

Step 3

D

7

8

Attach the drawer
sides to the drawer
front

Push the small left
drawer side and
small right drawer side .
. onto the back of the
small drawer front .

Turn the small locking
nuts on the small left
drawer side and
small right drawer side
. .

Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.

8

7

8

5

D

D

7

8

Groove

7

D

D

B

B

5

Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the groove is on the inside, as shown.

D

8

7